Leather Scroll Case

DIY Crafts & Art
164 followers
What up, fam?
Today I'm going to show you how to make this draconic scroll case of messaging.
Stay tuned.
For starters, I'm going to be using two spray paint cans of the same size to act as my forms.
We're going to be using these to wet form the top and the bottom rounds.
I'm also going to be needing a strip of the same six ounce leather that I'll be using
for the rest of the project.
By wrapping it around one of the spray paint cans, I'll be able to account for the extra
size needed for the cat part to be able to seat over the tube.
Using the diameter of the spray can as my guide, I adjust my compass so it's a couple
inches wider.
Then I draw out those circles onto my leather.
Now you don't have to be too careful with how you cut these out, as most of it's going
to be trimmed away in the end.
With my circles all cut out, I prep them for wet forming by putting them into some hot
water.
Once completely saturated, I take the rounds out and wet form them around the bottom of
the can.
Then hold them in place with a zip tie.
I then lightly tap around the bottom of the can with my mallet to make sure that any folds
and wrinkles are pressed out.
With the butt side of my tube all set, I then do the exact same steps on what will become
my cap side.
Next, I prop a pencil up to give it a little bit of height and use it to draw a circle
all around the edge of my leather.
I then use that ring as a guide to evenly space all of my stitch holes.
With both caps done, I leave them alone to dry, after which they perfectly maintain that
shape.
Now my bottom piece has this little gash here that makes it easy to tell them apart, but
you may want to make a little mark in an inconspicuous place so you can tell the difference, as they're
both pretty close in size.
Now I use that same pencil trick to mark the caps where I want them to be cut.
Then I put them back on the can for stabilization and carefully cut them out with a razor blade,
leaving me with these two perfect little bottle caps of leather.
Now I use my bottom cap to measure how wide I need my tube body to be.
Here I show a measurement of 8 7 8ths inches, but you need to remember to add on the thickness
of your leather or else you're going to come up short, making my measurement an even 9
inches.
So I lay out a line at 9 inches for the width of my leather, and I'm using 10 inches for
a height.
I also cut out an inch and a half wide strip that I'm going to use for this cap rim.
I just make the same measurements I did for the butt of the tube and cut my strip to length.
Finally I cut out a half inch strip that I'll be using for my belt, my keepers, and my buckle
assembly.
With all my parts cut out, I bevel all of their edges, and then use my slicker to make
sure they're all smooth and professional looking.
Next, I set my stitch groover to be the same depth as the holes on my caps, then use it
to mark all the edges where I need holes to be.
Now I just follow those lines to punch all of my lace holes.
Because I used the same fork to mark all the holes around my cap, the spacing should work
out perfectly.
Speaking of those caps, I also use this opportunity to punch out all my lace holes using a rotary
tool.
For a little added design, I decided to bust out my Dungeon Master's guide and found this
table that shows the Draconic script.
I then use that script to spell out Skilltree.
With that all planned out, I wet my leather and then position my design right in the middle.
Using my stylus, I was able to trace the design onto the leather, and then cut it in with
a Dremel tool.
Finally, I punch all the holes where I'll need my straps and keepers to be.
With all that setup done, I move on to adding some color to this project, using an oxblood
for the body of the tube, and black for all the trim and straps.
I also decided to use an antique just to make sure all of my script pops.
With everything colored just how I want it, I attach my straps to the main body of the
tube using rapid rivets.
I make sure to leave this extra little loop so you can hang it on your belt when it's
done.
I also add all the little keeper pieces to where they'll go on the cap.
With that all set, I start assembling everything together by using a baseball stitch to form
the rim of the cap.
Then I push the cap round in place and secure it there using a saddle stitch, leaving a
nice clean line.
I then also use a saddle stitch to secure my butt round to the bottom of the tube.
You want to do this before you close the sides of the tube so you can still get your hand
in there to stitch everything together.
Finally, I finish everything up by running my baseball stitch all along the seam of the
tube, making sure the edges butt together cleanly.
Now with everything all stitched up and looking pretty, I secure the cap to the body by running
the strap through all the keepers.
Now I'm able to safely lock all my documents away.
The strap keeps the tube from opening up accidentally and provides me with a nice little loop to
hang it on my belt.
And there you have it!
One epic Draconic Scrollcase of messaging.
Don't forget to like and subscribe, and as always, keep leveling up, you.
