電視開機屏幕一直閃?其實故障很簡單,2塊錢成本輕鬆修好【我愛電器維修】
我爱电器维修
89粉絲
#電器維修#電視機#電視維修#生活技巧
哈嘍,大家好
分享通俗易懂的維修視頻
讓維修從此變得很簡單
專業(手機,電腦,監控,家電)維修
喜歡我就訂閱我哦
https://www.youtube.com/channel/UCma9sHXyCIBoYmC0PzDmLNw?sub_confirmation=1
電視開機屏幕一直閃?其實故障很簡單,2塊錢成本輕鬆修好【我愛電器維修】
Fix an LCD TV and the problem with it is
And when you turn it on, look at the blinking screen
And then this standby indicator up here red
It's also flashing
Let's take a look at this picture
I see the flash is gone
Wait?
And then it goes on and on and on and on
It's like this
It's not the backlight bar on the TV
Let's take a look at this TV set
When it's on
Shine a flashlight on this screen
And then you don't see it on this screen
There are any words
We can tell from this
It's not the backlight strip
Now his problem is that the TV is in
Back and forth
In the boot process
He never got it going
It's like this
Generally it is the motherboard or power board problems
I think he might be the problem with the power strip
Now let's take it apart and examine it
When we open the shell let's take a look
This is the main board of the television
And this is the power strip for the TV
Now his problem is television
Over and over again always boot up
In this case, I suspect this is the power strip
Caused by low output voltage
He couldn't carry the load
Now let's measure it with a watch
See if his output voltage is normal
Two groups of output voltage on the power board
One is to co-charge this motherboard
What about the other group
It's connected to this backlight right here
The main thing we do is check
This is the part that commutes the motherboard
Because this TV doesn't turn on
The first thing is to check
Let's see if the voltage up here is normal
He has two voltages powering the motherboard one is 5.3 volts
The other one is 13 volts
Measure 5.3 volts first
Let's see what the voltage is
Now we see the voltage is 3.43
The voltage is obviously on the low side
And then when the TV is on
This voltage is gone in an instant
Voltage is obviously low
And then we measure 13 volts to see how much
13 volts here we see is now 8.8
This voltage is also significantly low
Take a look at the moment the television is turned on
Is the same
It went straight down to a little over a volt
Say so?
The problem is on the power strip
The next step is to check the power supply board
Mainly from the appearance of the first look at ah
Actually, this power strip
No matter what
There is a common problem with the power board above the electrical appliance
As long as the output voltage is low and unstable
The main thing we need to check
These filter capacitors up here
Let's look at that a lot of filter capacitors
And then the main thing is to look at its appearance
If there's a bulge or a leak or something
So let's take a look at the capacitance
There's a slight bulge on it
There's another small capacitor
The capacitor is bulging and leaking
And then you have these two capacitors here
It's also a slight bulge
In the process of maintenance, as long as the capacitance of the drum is found
Well, you don't have to measure it
Just swap them out
And then we run a power test
Let's see if there are any questions
If there are any more questions
I just need to check something else
The two capacitors are 35 volts 1000 microvolts
I didn't find the right one
But I found a 35 volt, 2,200 microtransmitter
Use this capacitor right here
To replace these two capacitors up here
OK, here it is. I have installed it
But on this side
One model of two capacitors is not the same
His original one
It's at 10 volts, 2,200 microvolts
I replaced him with a 16 volt, 2,200 microbeam
This is the same thing as before
He used to have a 35 volt 1,000
Now the four capacitors are the same model
After installing the motherboard, power on and turn it on
OK, that's all right
It shows that everything is normal
