Tutorial for making a traditional qipao/双襟旗袍教程
102 Video Views·Mar 12, 2024
This qipao tutorial shows how to take measurements, pattern making and steps for handcraft.
Hello everyone
Welcome back to my channel
It's been a long time
I've been making this cheongsam recently
It's a traditional full-lining two-piece cheongsam
This piece is completely openable
I made it a small vest to match
The content of today's video is to introduce this cheongsam
From the pattern making to cutting and
finally the production let's take a look
together at all the data required for this
cheongsam The data provided here is my size
The ease of this cheongsam can be calculated based
on your own measurements and adjusted according to
the desired tightness or
looseness of the cheongsam
When measuring be sure to note one important point
Take off all your clothes and get measured
Don't wear any clothes
because we need to get your exact measurements
Now I will introduce them one by one
The first measurement is your garment length
This involves an important point here
The neckline is the point where the
clothes reach up to the neck and shoulders
Then above that is your collar So
this neckline is always your clothes
The highest possible point is measured
directly to the length you want for
your shirt through the shoulder and
bust point which is our shirt length type
The second one is the front waist and back waist measurements
The front waist length is measured from the shoulder
neck point down to the waist The back waist length is
measured from the shoulder neck point to the back waist
The back waist length is longer than the front waist length because the front waist length goes over the
chest which has a curve and
a slope so our front waist
length is generally longer than the back waist length
When making a well-fitting cheongsam even
if your front and back waist measurements are
equal such as both being 42 you still need to reduce the back waist by two centimeters
The waistline must have at least a 2
cm difference between
front and back for the cheongsam to look good with no excess fabric gathered at the back
The front waist measurement is usually a bit longer than the back waist measurement For example the
difference between my front and back waist measurements
is two centimeters This is a direct measurement data
Measure your front and back waist lengths with a ruler
get your front and back waist measurements
The fourth measurement is the shoulder slope
it is a term used in Chinese clothing
Shoulder height equals armhole depth
This measurement is taken directly
Place the ruler on the shoulder neck point
and measure down to the desired armhole depth
The fifth measurement is the sleeve opening
It is a term for traditional Chinese clothing It refers to half the
shoulder width plus the length of the sleeve Traditional
Chinese clothing all have connected sleeves
So we need to join the shoulder and the sleeve for the base measurement
The sixth measurement to take is the knee height
Place the end of the ruler at the neck-shoulder point
Measure from the bust point all the way down to the center of the knee
The seventh size is the bust
The tape measure goes around the fullest part of the chest
Do not insert your fingers it is a net size
Add the ease allowance
There is one point to note here If there
is a back waist add an extra two centimeters to
the waist measurement When calculating the
chest size the eighth
is the waist measurement
The bust measurement is taken down to the waistline
just take in 3.5 centimeters
the ninth measurement is the hip
measure around the fullest part of the hips with a tape measure
plus the ease allowance
You can adjust the ease according to your comfort level
The tenth size is the neck circumference
The tape measure goes around the base of the neck
The ease should be adjusted according to individual preference
This cheongsam has a 2 cm ease in
the neckline which is the smallest
ease I can accept The eleventh measurement is the height of the slit
I want the slit on the qipao to be five centimeters above the knee
so the measuring tape starts from the neck-shoulder point
and measures down to five centimeters above the knee
which is the slit height
The last measurement is the sleeve length
Measure the desired size on your arm with a ruler
Then distribute it to the front and back pieces
These two body sections are now complete
Next it's time to create the pattern
Understand the drawing order before starting
First length then width then contour
Dimensions marked in red
Are the lines used for drawing the length direction during drawing
We are still missing a hip height line
here Just add 20 centimeters directly
below the waistline This range usually
won't be a problem Marked as the blue size
These are lines drawn in the direction of the board's width
when making the pattern The dimensions we both obtained
are the full circumference dimensions However when making the pattern we only need a quarter of the dimensions
So the bust and hip measurements we just got are both increased by the
ease allowance and then divided by 4
to get the size we need for the pattern
The waist was not calculated when the pattern
was made but instead directly taken as a quarter
of the bust measurement and taken in 3.5 centimeters
This is to make the overall line look better
Even if the waist is slim you don't need to take in
too much But you should check the size of the front
and back waist on the pattern It should not be less than the net waist size plus the ease allowance
Next subtract three centimeters from one quarter of the hip measurement
this is the hem size
mark this as the black size
They are lines used to draw details inside the front and back outline
when drafting This area around the neck is also a circular measurement
We also need to calculate the neck size on the front
and back pieces at the quarter points So now we have
the measured dimensions and all the data obtained after
calculation Follow me as I carefully draw each step
You can make the pattern for this cheongsam
Before the video on starting to draft the pattern
Let's first talk about how to choose our fabric
In winter you can choose materials like wool
When the fabric has a heavy feel the winter fabric
Then let me talk about the lining
The material should match the main fabric
Like when I was learning
The teacher recommended we use this type of silk cotton fabric
It is a blend of silk and cotton
Its price is not expensive
It is about 35 yuan per meter
For traditional clothing
You must definitely buy real silk sa
Never buy fabric with
a painting pattern
The difference is that when you apply
glue silk fabric won't get dark but
painting pattern fabric might get wet
The weight you buy is 16 to 19 millimeters
The current silk price is 75 yuan per
meter You can buy these fabrics online
Or each city has its own fabric market
Let's take a look at the video
of the pattern making I hope
you can study carefully The first step is to draw the main
outline The upper horizontal line passes through the apex
point Draw the highest position of the garment on the body
Next draw the horizontal line
parallel to the top edge Then
draw the vertical lines at each height The shoulder line is
also the sleeve cap line The
front and back waist height The
hip height line The knee height
line The garment length line
Draw the front and back center lines
Step two draw the front and back bust measurements on the shoulder line
Step three draw the front and back waist measurements on the waistline
Draw the hip circumference of the front and back pieces on the hip line
Draw the hem size of the front and back pieces on the length line
Draw the distance of the arm's reach outward from the center
If you like me have sloping shoulders
A particularly prominent left hip
Like the kind that can keep a goldfish and a coin
Slope the shoulder down 4 centimeters at the front piece's shoulder end
The front piece's sleeve also drops down 4 centimeters
And draw your own shoulder line on the front piece's small shoulder line
This can alleviate some pressure from the clothes
on the collarbone It makes the front fit more closely
to the shoulders It takes some of
the weight of the fabric at the collarbone area I made a mistake here
It was after trying it on that
I raised the shoulder line by 2.7 centimeters from 23.5
to 20.8 When I put on the cheongsam I felt my
shoulders were all tucked inside the garment
It really pinches the collarbone
maybe because there was not enough space under my armpit
to compensate I added a 1.5-centimeter protrusion at the shoulder area
I was lucky I left 2 centimeters for seam allowance to have room for adjustments
Step seven at the midpoint of the sleeve is where your sleeve length is
Draw a vertical line upward to mark your sleeve width
Also the size of the cuff
Step 8 Connect all the measurements
Draw the outline of the front and back pieces
Step 9 Based on the calculated data
and smoothly draw the shape of the neckline
Everyone's neck has a
different shape Even if two
people have the same neck size one
person might have a slim build and the other a stocky build
resulting in completely different neck shapes
When making the pattern adjust the neckline
according to your neck shape My neck is
flat My back is flat
My chest and collarbones
are prominent So I widened the front V-neck
The back neck opening remains unchanged On the contrary the person in the back needs to increase the back neck
opening Step ten draw the shape of the shoulder You can
refer to some pictures here You
can also refer to these data
Draw the broad shoulder shape you want
You can see it on many old photos These
shoulders are quite wide This allows for
enough space to fit many rows of buttons
I initially wanted to put a row of buttons
on this but there wasn't enough space
so next time when I make a double shoulder
running jacket I'll draw it a bit wider
Draw the slit height on the front and back pieces
Step twelve add the back waist darts
My version of the cheongsam has two back waist darts
It's because I wanted the cheongsam to fit
better at the waist but
still not affect the side
curves so I took in the back waist with two darts
When drawing the back waist darts be careful
Because Asians have longer backs the
most concave part of our back is not
on the waist line but at a position
2.5 centimeters below the waist line
The most intense part of the back waist is about 2.5 centimeters below
the waistline Also the back waist
should be drawn in a jube paste shape
This will better fit the curve of our back
Step thirteen: draw the collar
First measure the curve of the front and back necklines
Then draw your collar shape according to the size of the front and back necklines
The standard cheongsam collar stands
up about 1.7 centimeters at the
front neck opening and smoothly connects to the shoulder neck point
It's also where the back of your neck ends
If the measurements above and below your neck are about the same
then 1.7 would be completely fine for you
but if you're like me with a narrow top and a broader bottom
My stand-up collar will be very large as large
as 3 centimeters the more
the lower collar stands
up the smaller the upper collar will be so this
stand-up amount can also be adjusted flexibly
Don't just memorize it as 1.7 try it
according to the shape of your own neck Last
step step on the main tendon of the front piece and the small tendons on both sides
The left side seam is sewn together with the back seam The right side
seam is completely open There are
nine buttons attached to the side seams
So add a 7-centimeter wide base reinforcement
under the right small seam to prevent
skin from showing when worn The left small seam is shaped under the large seam
Add 5 centimeters of overlap
Next add seam allowances to each pattern piece
Front center dart
Front left small dart
Front right small dart
Front right bottom dart
Back piece
Add 2 centimeters of seam to the front and back seams and side seams
4 centimeters of seam at the bottom
Add seam to the front middle part of the left and right small seams
The other parts are all 1 centimeter seam
allowance The pattern for the neckline is cut
as a flat piece Do not add any seam allowance
Finally mark four lines on these pieces
Write the name of each part on your cardboard
Don't forget to draw the alignment points on the key areas
That's before you start making the video
I want to give you some advice
How do I usually learn about traditional clothing
First I read books
The first one to introduce is this set of books
The first book is about basic techniques
The second book is about making a cheongsam
The last one is about making Tang-style clothing
The second one to introduce to everyone is this English book
This book explains clothing from the details
It is accompanied by detailed computer graphics
The benefit of this book I think is that not only can
you see traditional Chinese clothing but you can also see
the traditional costumes of various ethnic groups The third
book I would like to recommend to everyone is this one
This book showcases detailed information about
each cheongsam and its owner who were all famous
socialites from the Republic of China era and you can
also find a lot of inspiration from these pictures
Learn what real old Chinese cheongsams
look like In addition to reading books I often search for tutorial videos online
Watching others' videos is also very good
Because everyone's thinking process is different you will definitely learn
something from others' videos That's
the last way I learned by taking classes
Before everyone saw me making these clothes
I had already taken many classes so these
courses might be a bit more expensive but
you can really learn each step systematically
Compared to making pattern making is actually
quite simple You can't learn them all just by
watching a video That's impossible So you must
accumulate knowledge
over a long period of time
The teacher told us a saying during class: "
Practice makes perfect "
You can watch a
hundred times but it's better to do it once Not right
You can watch a thousand
times Really do it once
Your feelings are completely different So we
especially encourage everyone
to get hands-on Gather the
courage to get started You will definitely do better
each time Now let's talk about the craftsmanship
The first step is to make a paste The paste
is made with flour One cup of flour with
three and a half cups of water Pour the
flour and water into a bowl and mix them well
Heat over medium flame and add in four portions The
first time beating the sauce it should take about
30 to 40 seconds The sauce will still be
in liquid form Beat for one and a half minutes the second time
It becomes slightly solid at this point
Also scored 1.5 points the third time It'
s already like a solid What about the
last time The dough
should be almost cooked
After cooking it becomes elastic
The sauce is now ready
You can eat it now
The second step is to soak the fabric and
lining If it's a casual style both the
fabric and lining need
to be soaked If it's
a formal dress style just steam the fabric
The third step is about the embroidery the
key is to check the
accuracy of the embroidery
First draw the front and back center lines
and all the height lines on the fabric
Stitch the fabric with a large stitch pattern
Step four cut the fabric and lining
Turn the fabric to the wrong side
Align the center line of the pattern with the previous large stitch marks
The front and back center lines are roughly stitched
Then align all the height lines in order
Draw the outline and details of the cardboard
Cut along the lines
Next cut the lining material
The main piece is laid flat on the lining
Cut the lining along the outline of the main piece
Be especially careful here
The hem of the lining should be cut into a curved shape
This step is to ensure that the bottom of the
cheongsam does not reveal the lining The fifth step is
to sew the waist of the fabric and lining First use
safety pins to fix a few points on the waist area
The seam is 0 5mm outside the line
After sewing the straight line where the collar is folded must be curved
so there is enough space to press it through
Step six handles all the details of the fabric and lining
This step is not difficult but very tedious
First we will prepare the fabric
First press the back and underarm areas
These two areas lie exactly along the body's natural
curves so we need to transform the flat piece into a three
-dimensional shape first by shaping it into a straight
line with the excess fabric all gathered on the thigh
We use oil spun tape to fix the shape of each part
so that it does not deform
during production and wearing
fix them separately on the side seams
hem
The main seams the secondary seams the cuffs these five positions the four edges of
the front and back
pieces on the left and right sides must all be equal the third is
on the position where the
seam is finished with a binding
Use paste to assist in pressing and steaming
The side seam of the back piece only processes the distance below the slit opening
The inspection opening is at the slit opening neck line
Apply 0.6 cm of paste then fold and
press while doing so The front piece
has a hem all around but the left
seam needs to be sewn to the back piece
Keep this section as a seam allowance
Hem is directly folded and pressed
And sewn with large stitch to fix
Now let's handle the lining
This step is much simpler
First position the seat and underarm areas The
inner fabric does not need to be glued or pressed
with a strip Next lift the bottom edges of the front
and back pieces to allow space for double folding
Stitch or hand-sew permanently
Step Seven
First sew the connection line between the right small muscle and the bottom muscle
Sew the hems and linings of the left and right
side seams together When sewing pay attention to
two points First the distance of this section from the front center on both sides must be equal
Second when sewing the hem pull the thread
We have reached step eight
sewing the shoulder seams
sewing the shoulder seams of the front left and right pieces to the shoulder seam of the back piece
Attach the lining of the front piece to the
lining of the back piece Step 9 Bond the fabric and lining Scrape 0.3 cm of paste
from all areas where buttons have been pressed
Attach to the corresponding mirror line on the back side of the lining
When bonding the side seams of the lining
it needs to be lifted by 0.5 cm
The amount to be gathered is evenly distributed along the side seams
Step Ten
The areas to be stitched with a facing are the entire front piece
the left and right cuffs
The side seam line extends from the hem to the hip line
The slit's vertical line is 5 cm above the knee
but the binding must continue all the way to the hip line
To prevent the lining from fraying we wait until we sew the edge binding to
trim the lining neatly It is best to use 16mm
needle-punched satin for the edge binding
Apply glue to the back of the needle thread three times Once the needle thread is naturally
dry Use a bamboo ruler to soften the glue on
both sides of the needle thread and then iron it
The width of the binding is calculated
according to our design Cut the binding
at a 45-degree angle Sew it to the
embroidery Note: keep the binding seam narrow
Otherwise the width of the rolled edge will be
insufficient You can now do the rolled edge on
the reverse side or you can do it later when you
have time The last 4 cm of the embroidered edge
Don't sew the end by hand now Wait until you sew the
side seams and enclose the edge of the front piece
Stitch the side seam where the front piece's main seam overlaps with the left small seam
Step 12 sew the side seams of the front and back pieces together
You can see it once you sew the main outline of the side seam
Step 13 is making the collar
Next we also clean the collar lining thoroughly
Shaving and then immediately hemming the edge is
the final step The last step is making the button
Because the craftsmanship for the collar button and the decorative button is relatively complex
This issue will not go into more detail
We will explain in detail next time
That's all for this video tutorial
I hope you have gained something
I also want to start now to make
some good cheongsam tutorial videos
Which specific part do you have questions about
or are interested in You can leave a message in the
chat and I will make a detailed tutorial If you
have the opportunity to attend a class in Beijing
My teacher will offer a public class after the Spring Festival
The price of a complete set of courses is between 5000 and 10000
But this time the price of the public class is 200
yuan which is well worth experiencing The time is one
day actually just to give everyone a chance to
experience it What can you
get from this kind of course
If you're interested in the public class leave a message and tell me
I also want to thank all my friends who leave messages
your encouragement each time motivates me to make these tutorials
it's what gives me the motivation to create these videos
If you like this kind
of video be sure to
subscribe to my channel see you next time
