戶戶通機頂盒不開機,一般都是這裏問題,10幾元買個小板換上就好 #我愛電器維修
我爱电器维修
89粉絲
2024年3月8日 #我愛電器維修
我們的視頻是為了為觀眾提供有價值的內容,絕對沒有任何違規行為。 非專業人員請勿直接操作!
哈嘍,大家好
分享通俗易懂的維修視頻
讓維修從此變得很簡單
專業(手機,電腦,監控,家電)維修
喜歡我就訂閱我哦
https://www.youtube.com/channel/UCma9sHXyCIBoYmC0PzDmLNw?sub_confirmation=1
戶戶通機頂盒不開機,一般都是這裏問題,10幾元買個小板換上就好 #我愛電器維修
#我愛電器維修#家電維修#電器維修
Repair a Huhutong set-top box
The problem with it is that it can't be turned on to take a look.
Nothing happens after booting
Finger lights are not on
Now let's take it apart and fix it
see what's the problem
after opening
Let's take a look at its interior, there are two big boards
This board is its power board
Then this is the motherboard
Nothing happens when booting like this
like this situation
Generally, it has something to do with the voltage board.
It's the voltage board that's broken.
But how can we quickly judge
Is it the voltage board or the main board?
what about this time
You need to measure it with a watch
Measure the voltage board and its output
Check if there is voltage output
The output voltage is normal or not
If there is no voltage output it proves that it is broken
If there is a voltage output, the output voltage is also normal.
So this problem is the problem of this motherboard.
There are five wires on this voltage board
When measuring, first find the JND above
this is his d line
Then look at the fifth pin, which is 5 volts
uh that's 5 volts
Use the copy chart to measure the two inside angles
Power on first and then turn on the switch
Check if his voltage output is normal
This is 5 volts
Look at its output voltage, now it is
Jumping back and forth between 1:00 volts and 2:00 volts
The voltage is very unstable
And the voltage is also very low
too low
sure he can't turn it on
this circumstance occurs
we still can't judge
It's the voltage board that's the problem
It's a problem with the motherboard
We first need to put this
Disconnect the line connecting the voltage board to the motherboard first.
Disconnect it and then measure it again
Where are they?
Now the voltage is still the same, see?
It's still a triangular multi-volt jumping here all the time, isn't it unstable?
The normal voltage is 5 volts and now it is more than 3 volts
Still the difference is quite big
Now we can figure out what's wrong with it
It's just that the DNA board is broken.
When measuring DNA plate output DNA
Why should this line be disconnected for it?
What do you mean by disconnect?
just avoid
It's a severe short circuit on this motherboard.
Well, it will appear that his output voltage is low
So after disconnecting it
then measure
Check if his output voltage is normal
If it is normal, it means that the voltage board is fine.
His problem appeared on this motherboard.
Well, if his output voltage is not normal
So it's the voltage board that's broken.
Now let's remove this power board
Let's check to see what it is
What is the original bad cause
Its voltage output is low
Voltage board output voltage is low
like this situation
Generally
These filter capacitors at this output
After capacity failure
He will appear low voltage and unstable
poor affordability
there is another situation
This is the main filter capacitor
If his capacity becomes smaller
It will also appear that the input voltage is low
After I checked
Found that the originals weren't broken
no problems found
Then the small resistors of these patches on the back
uh it's okay
Well
Including the above diodes are no problem
Then his problem is only
This is the chip like that power off
There is still this optical couple and 431 that have not been replaced
no check
repair like this
It's more troublesome.
There are also other repair methods that I suggest to everyone.
just replace one
Such a small board will do
In fact, it is very cheap to buy such a board.
I bought this one for 10 yuan
it can be replaced
It's the same if you replace it
This method is the easiest to repair.
and the fastest
if small problem
Just give him a fix like this and it's over.
If a little more complicated
replace directly
because it takes too long
It will be repaired later
and this income
The cost is disproportionate
So just replace it with this one.
Like when we are repairing other electrical appliances
the same
Uh, if it is too troublesome to repair, just replace it directly
It's not necessarily when you change it.
Its appearance and model are exactly the same to use
In fact, it looks like these two look different
The most important thing is to look at its output voltage
As long as the output voltage is the same
Appearance doesn't matter
The wiring order is different
In fact, it can be changed
We mainly disconnect this for it now
Then solder it on
let's test
Let's see if replacing this fixes it
When this set-top box is finished?
Turn it on and test it to see if it can turn on
Uh, this has been changed to free positioning
Take a look at his module
The light above is already on
It means his voltage is normal
look at this display panel
It's booting up normally, no problem.
