The owner of a small company
contacted me and told me
that there is a conveyor belt in his company to
start which a start push button has to be
used and to
stop the conveyor belt a stop push button has to be
used. Apart from this,
two types of boxes will be kept on top of the conveyor belt,
which will be shifted from one place to another,
one will be a smaller
box and the other will be a bigger box. Now
he also told me that
if there is anything on top of the conveyor belt, If the smaller box
goes, the blue light
should glow and if the box above the 12th box on the same conveyor belt
goes, then
in this condition the yellow light should glow,
then the entire working of this conveyor belt
is working. According to them,
they asked me to make the entire panel. To make the panel that is there now, I
told
them to put two limit switches along the conveyor belt and one
limit switch at the bottom. Place it on the side and
put the other limit switch on the top side. By
using that limit switch, you
can easily make the lamp glow. Now
along with making the lamp glow, you
also have to run the conveyor belt, then
how to make the entire circuit. I
explained it to them in full detail. What did
I tell them? Let me explain it to you too.
See, if a motor is used to run the conveyor belt,
then a contractor has to be used to provide power supply to the motor.
I told them that the
wiring of the conductor will have to be done in this manner.
Now I told them to make
a control circuit diagram to switch on and off this conductor. What
they had to do in the control circuit diagram is
that the phase supply is Take that phase
supply and connect it directly to the stop push button
and
connect the power supply from the stop push button to the start push button.
Now connect
a wire from its terminal to the start push button. I took it and told them to
connect it with the A1 terminal of the
contractor. After this I told them to
directly provide neutral power supply to the A2 terminal of that contractor.
What will happen after doing this much work? To
start their conveyor belt, they
can start it by pressing the start button, but as soon as they release the start button,
their conveyor belt will stop. I
also told them this, so as soon as I
told them this, they told me this
That after making the start button, it has to be pressed only once. The
motor should keep running. To stop it, you have to press the
stop button. Tell me such a connection.
So I told him that the conductor which is the
anode contact of that contactor, that anode
contact should be connected to the start push button.
Connect them in parallel. Parallel means looping a wire from the
input terminal of the start push button
to connect it to the anode contact of the contactor and
a wire from the output of the start push button. It has to be taken and
connected to the output of the anode contact, meaning that
I told them to make the connection in this way,
now in this way they made the complete connection,
after making the connection, they
pressed the start button and the motor started,
meaning that The conveyor belt got started
and to stop the conveyor belt,
he pressed the stop push button and the
conveyor belt also got stopped. Now he
said that this much work has been done,
tell me about the next circuit too, that is, the
conveyor belt. Please also tell me the connection to make the accordion lamp glow in the box which will go on top of the belt.
When he requested me this, I told him that
you have two limit switches to provide
power supply to those two limit switches.
Take the power supply from the output terminal of your start push button and connect it to both the limit
switches in this way,
meaning that from here the phase supply will go to this
limit switch and from here the power
supply will go to this limit switch.
Now after making so many connections,
I told them to
take the power supply through the down limit switch and
directly
connect it with the blue light of theirs.
To make the connection in this way,
After I said this, I told them to
take a wire from the output terminal of the upper limit switch and
provide phase supply to the other light, i.e. the yellow light,
and to both the lamps.
To make it glow, you also need a neutral power supply, so provide the
neutral supply directly, there will be
no problem, everything will
work, so this is how I
told them the connection. After telling them the connection,
I told them to check it once they run it.
Take, when the owner of the company
pressed the start button after doing the wiring, he
saw that the conveyor belt
started working. After this, he
noticed that when the box which was going on the conveyor belt, the
smaller box was moving on the smaller one. The
light switch below the box is being operated due to which the
blue light is
glowing and as soon as the box is moving from there, the
light is going off.
After this he told me that the
bigger box is the one. If the box goes, then
both the limit switches are being operated together
and both the lights are glowing together
which is wrong, only they
need here that if the big box
goes, then only the yellow light will come on. The blue
light which is glowing should not glow,
so
how did I
solve the problem that was coming at that time, let me tell you also,
so how to solve the problem that was there.
So I told them that
they should simply use a small relay
and bring that relay
and after bringing it,
connect it parallel to their yellow light, that is, the
light. By
looping a wire from the same phase supply to the relay, I have instructed them to
connect the wire to the A1 terminal of that relay
and to directly provide
neutral power supply to operate the relay. I
told them
and in the same way they made the connections
and after making the connections, I
told them to remove the wire of their down limit
switch
and
after removing it, I said that
a wire has to be taken from the output terminal of the down limit switch and
provide incoming power supply to the NC contact of the relay which is its relay. To connect the
power supply from its output terminal through the NC contact and
connect it with the blue light, that means
I have used the NC contact of the relay in the middle of the wiring that was there. I told him that
after making so many changes, I made the entire
circuit run automatically and showed it to him. I
told him that
if he presses the start push that needs to be changed, then the
motor will start. Now with the motor
running, the conveyor will start. The belt will also start
and if the conveyor belt starts running
and if a small box goes on the conveyor belt, then
in this condition the
lower limit switch will operate and due to its
operation, only the blue light
will glow which was earlier. Now
after this I told them that if the small
box is removed from the limit switch
then their lights will be switched off. Now after this
I told them that when the big box
comes, that box will be switched off. The upper limit
switch will operate as well as the lower
limit switch will also operate but
only their yellow light will
glow. This will happen because the
NC contact of that relay
breaks the power supply.
He is also doing that to the blue circuit, due to
breaking the power supply of the blue circuit,
only their yellow light will glow
when the big box goes and
after the box goes, the limit switch here will be
removed. Meaning that it will be reset and
no light will glow after the reset.
Now after getting all this wiring done,
I also told the owner of the company that if
you want to do the wiring yourself
like it is any machine, then
automate it. Making a starter, making a panel,
if you want to do the wiring yourself
without taking anyone's help, then for this you
can easily learn the entire work by joining my course, Electrical Wiring Master Course, so
friends. He was the owner of the company, yet
he joined the course and
after joining the course, he made a small circuit
by himself.
I will tell you what he made in the next class,
but if you also want to complete this type of circuit yourself. If you
want to do wiring, that is,
if you want to learn wiring, then
join my course. To
join the course, you will have to
download my app.
You will find the link to download the app
in the description. You will find it there, click on it
and download it and
after downloading you can join the course directly.
If you need any help, my
mobile number is given here. If you want, you can contact me directly by
messaging or calling on this mobile number. You
can talk, whatever is your query,
I will solve that query. I hope
that today's video will be
liked by you. If you like the video then
please like it. Thanks for watching this video.