Lecture 16

IIT Kanpur July 201
20 followers
Mar 1, 2024
[Music]
[Music]
hello and welcome to this uh lecture on
Microsystems fabrication by Advanced
manufacturing processes a quick review
of the previous lecture we were uh
discussing about Electro stream drill
Drilling in great details I just like to
recall that it's a process where there
is uh the electrolyte itself is the
electrode okay so the electrolyte is an
acid stream which is negatively charged
and it represents the cathode although
it emanates out of
a an electrode which is otherwise
insulating in nature uh it uh generates
a cathodic effect a virtual cathodic
effect and uh the workpiece made the
anode dissolutes and whatever ions come
out of the workpiece are not
precipitated or uh they don't react with
any any other constituent in the acid
electrolyte itself and so they are
dissolved as ions and therefore the
process doesn't need any ref flushing uh
because there is typically no nucleation
or no particle growth uh based on
electrochemical processes so we looked
at how ESD can be used to drill inclined
and steep angular holes and Cavities we
also talked about the two different
variants that ESD has called the dwell
Drilling and the penetration drilling
depending on whe that
the
the stream dispenser the electrolyte
stream dispenser is a static or is
moving at a constant rate or a constant
feed towards the work piece uh we also
sort of uh did a recap of the ECM uh
basic process and the process capability
associated with ECM and then we talked
about how electrochemical micr Machining
is an absolute need for the several
applications in the industry and discuss
some of these applications and some
research uh in the area of ecmm or
emm just to recap a little bit we uh
showed this particular illustration here
where with the various pulse durations
in the nanc regime varying between 50 uh
Nan to 2 nond we could see how uh the
resolution changed and how the inter
penetration distance also changed
fortunately so uh in this particular
illustration we used a 2 mol
HCL uh pulse amplitude and then we also
considered uh 2.2
volt uh voltage with a 10% duty cycle
okay and then we also the the authors in
this particular case tried to also
measure the work piece and the Tool uh
voltages surface potentials uh and found
out a machining speed of 2 mm per minute
okay experimentally as well as through
um
modeling
approaches so what also is important is
the spatial resolution and uh the width
of the lateral gap between the tool and
the work piece obtained for different
pulse durations that is the gap width is
calibrated as a function of pulse
duration and you can see the Gap W
steadily increases with the pulse
duration meaning thereby that more is
the uh more is the duty cycle of the
pulse or more is the duration during the
during which the pulse remains on the
work piece is subjected to More Voltage
for greater amount of time and dissolves
more okay uh we ecmm is also applied in
this particular case where Ultra Shard
voltage pulses again are used for
obtaining um this copper tongue for for
example okay this is an SCM image of
this copper tongue uh and this has a
thickness of close to about 2.5 microns
okay this is how small it is uh
thickness wise it's etched by a 2
megaherz sequence of 50 nond
pulses of duration uh of of magnitude
1.6 volts okay the tool in this case is
a 10 micromet diameter mechanically
flattened piece of platinum and it just
uh you know very nicely compares to a
ant leg this here right here is an ant
leg and uh you can see the scale is
almost comparable in the SC image which
is above and below uh to each other
which shows the typically the process
capability of the system okay this is a
50 Micron scale this is a 5 Micron scale
so about a 10th uh that's about the
comparison so
uh this uh uh particular Machining
process used an electrolyte which was
0.01 molar Hydrochloric
uh
hcl4 and 0.1 mol
cuso4 the other illustration is given by
an insute formation of a single hole on
a gold uh substrate by using a voltage
pulse of duration 50 NS again of a 2vt
magnitude and this is utilizing 1 molar
copper sulfate and 0.5 mol uh sulfuric
acid Solutions now the hole is formed in
the location uh of the tip during the
application of the
pulse and uh this is represented by The
Black Arrow the whole formation process
the initiation of the whole formation
process has been shown in this
particular
uh schematic a photograph and you can
see that there are about three single uh
copper clusters on gold formed by three
50 nond 3vt pulses uh to the STM tip uh
again in the same electrolyte solution
okay
so due to the formation of this kind of
a copper so-called electrode you can
have an inverted feature hole uh created
as in figure a but what is important for
me to tell you is the resolution here
this is being done at a resolution of 10
nanometers which is Way Way Beyond what
you have seen so far so with ultra Shard
voltage pulses you can actually write as
well as develop tools or electrochemical
Machining at this particular scale of
few tens of
nanometers some other important features
of this is the tunneling voltage and
current tunneling voltage is in the
range of -300 mvts and the current is
about 1 nanoamp okay in this particular
case so that's about how small the ECM
process can go and still have a
resolution so this resolves very well
with one of some of the current high
energy beam processes like
FIB xray lithography so on so forth so
this is another example U borrowed from
zoo at all in
2009 where they're talking about a
perforated cathode okay so this is a
perforated cathode and the anode here is
the work piece and there is an
insulation layer which is in between
okay uh which is also like a
mask so there is a mask which
exposes certain regions of the cathode
to the uh work piece and uh going to
this particular uh Arrangement the emm
or the electrochemical micro Machining
is able to drill uh holes with such fine
resolution close to about probably 0.5
mm okay each of this hole must be in the
range of a few hundred microns I'm sure
and uh this is a blown up PM image of
the same uh whole array okay and this uh
right here illustrates the
cross-sectional shape of a single hole
so the work material in this case which
is made the anode is a work piece which
is a chromium alloy uh 1 chromium 18 and
I uh 9 titanium the thickness of the
work piece is about 0.3 mm that's about
300 microns okay and the cell voltage
that you're applying to do this this
Machining here is 18 volts so this gives
you some feeling of uh the kind of
voltages resolutions and whole diameters
that you can achieve with different work
pieces yet another example is borrowed
from uh Lawrence scrub
uh as can be seen in this illustration
here this was reported in
2003 and uh this talks about again
electrochemical micro Machining of
stainless Steels by Ultra shot voltage
pulses uh the figure here is an SCM
image of a pyramid which has been etched
into a stainless steel sheet and again
with electrochemical pulse method it's
uh conically shaped you can see the
conical shape right about here in the
center uh and uh the this case is a
Tungsten wire with less than 5 microns
diameter and uh it it was moved similar
to a uh uh Milling cutter that's how um
the process was accomplished and uh as
you know a Milling cutter is actually uh
moving linearly on a Surface in this
case although it is not a metal to metal
contact like a typical Milling cutter
would do with a uh surface in this case
it is a electrochemical Machining or
electrochemical Milling operation which
does most of the material removal so it
is a dissolu the material Away by a
circular tool so this moves uh all
although it is itself about 0.5 microns
it moves along a path here which gives
you an illustration of how this uh
cavity
was
uh made or realized in a stainless steel
sheet there was a p duration of 25 n
seconds that this group used and the
pulse value was about 2 volts um the
electrode electrolyte that was used in
this case about three mol HCL and a six
molar hydrofluoric acid combination and
uh the independent workpiece and Tool
potentials were measured as minus 200
and- 100 uh Mill volts respectively with
respect to a standard hydrogen electrode
this again is another illustration of uh
what is a process capability related to
ecmm you can see for a pulse durations
varying from 50 NS to 200 nond there are
different whole diameters of the range
of close to about 30 to 50 microns uh
which are obtained at different pulse
magnitudes so this is an array 4 volts
200 NS 3 volts 200 nond these are the
different whole diameters being made the
different voltage nanc combinations in
this case the tool was a cylindrical
Platinum wire okay and it had a diameter
tip diameter of 50 microns and uh uh
reported values here indicate what kind
of electrolyte was used it's again a HCL
um hydrofluoric acid combination and the
work piece potential and the tool
potential are rated as minus 120 and 80
uh molts with respect to a standard
hydrogen electrode
um there are some more examples here is
comparison of the holes again drilled in
stainless steel uh with different
electrolytes okay so you can see the
combinatorial used here by varying the
different malities of the hydrochloric
acid with respect to the HCL and you can
see various surface topologies being
generated based B on the different
electrolytes so by and large this
happens to be the best
combination to do ecmm so a process
balancing like this has to be made for
um good Machining to
happen here again is a very beautiful uh
sem picture of a prism okay and this has
been designed with a computerated uh
program
and uh it was H in stainless
steel and this was actually done with a
fast rough cut of 143 nond pulse
duration uh using CMM and then there was
a slow fine cut of 50 nond pulse
duration used in this particular case
the tool in this was again a cylindrical
tungsten wire with 30 micrometer
diameter so typically the um movement
here is in a similar manner as happens
in most of the computer driven tools
where there is a path uh geometry which
is provided in terms of a cad file and
uh the XYZ stage is set in a manner so
that it goes between different
coordinate values in a in a manner that
CNC also uh happens so it is a sort of
computer numeric control uh which is uh
uh which directs the tool to move in a
certain path which would uh relate to
the fabrication of the eventual feature
shape and size so this is otherwise very
hard to achieve you can look at the
scale here it is about 50 microns
meaning thereby that this one side alone
is close to about 50 microns okay and uh
the whole depth or the whole width here
is about 100 by 100 microns and uh the
depth also it cannot be figured out here
in the SCM but it's actually about 100
microns also so getting such a feature
using um
non- lithography non- energy beam
techniques is highly highly cumbersome
unless you go for electrochemical micro
Machining so there's some beautiful
illustrations of Milling electrochemical
Milling here you can see um this is
Borrowed by uh Kim atals work published
in 2005 where he talks about the
fabrication of a micro hemisphere with
about 60 micrometer diameter Machine
by uh a rough as well as finish Cuts uh
the electrode used here is about 45
Micron uh diameter electrode uh it's a
wire and uh the material that you are
using of the electrode is stainless
steel
304 and uh basically using a 6vt 60 nond
pulse on time duration for a 1 microc
period to achieve this particular
feature right here beautiful uh again
micro feature Illustrated on stainless
steel similarly you this again is
another example where a micro column has
been uh with with a width of 40 microns
and a 20 Micron length and 85 Micron
height so very high aspect ratio has
been machined by again a 65 micrometer
dis type electrode okay and uh this is
again an example of Milling where the
electrode is rotated because of which
there is uh Machining taking place at
this mic this Nano Nan ometric level so
use a um
304 uh SS stainless steel electrode in
this case with 60 volt 60 nond pulse on
time duration and for a 1 microc period
this another is an illustration of a
micro wall with 10 Micron width so this
is about close to 10 microns okay and 80
Micron height which is this height right
here okay Machine by a 65 micrometer
diameter dis type electrode again using
the same material 304 stainless steel
with the 6V 60 nond pulson time duration
for a 1 microc period
okay so one aspect which is a learning
experience from this uh particular work
is that it is very difficult to reduce
uh the taper only by controlling the
pulse condition and uh because
electrochemical Machining as I think I
have Illustrated many times earlier is a
self tapering process and so a uh
typically a better idea would be to use
a dis type of electrode okay which in
this case they have used uh katol has
used and uh you can actually have high
aspect ratio of your micro
structures if the Milling tool is dis
shap
it
so again some very nice illustrations of
ECM so let's now look at a little bit
different process EDM and I think I had
uh detailed in the last lecture why we
need to look at this particular process
because uh although we are going to do
the uh numerical modeling and the
process details uh later but in from an
application standpoint uh ECM is
combined with the Z M process to
formulate a hybrid uh making Machining
strategy which is called ecdm it is
electrochemical discharge Machining and
so you must understand the basic
principles Etc here and some application
standpoint what EDM does and how ecdm
would be different from ECM or ecdm EDM
so that's the reason for uh using this
right here so just a brief uh summary of
what uh this process is about so there
is a electrode okay which is Mobile in
nature and uh it's basically the cathode
and the workpiece is made the anode here
and instead of putting a uh
Electro
chemical
um
or instead of putting an electrolyte
here or electrochemical agent here uh
you put a insulating dialectric
fluid and the the advantage of a
dialectric fluid is that it provides
a a path between the tool and the
workpiece right about in this particular
Gap okay which is non-conducting in
nature so as this path is non-conducting
and you keep on charging this potenti uh
to a to a higher negative potential
uh there is a tendency that uh the
medium which is very small in this case
which is an insulating medium breaks
down and there is a discharge which
happens because of the charge
difference from the cathode in this
particular case so a discharge is
typically a momentary stream of
electrons which is released to by um the
cathode and they are driven by the field
and the positive potential of the anode
and they are accelerated and then in
this condition they hit upon the work
piece okay which uh leads to the uh uh
discharge okay of uh
the it leads to a situation where this
discharge creates an abl or a thermal um
thermally a bladed Zone uh with a melt
pool okay and uh as the electron
pressure reduces on the surface there is
a tendency of cavitation to happen
because the medium itself is not so fast
as the electron velocity and it has high
inertia and so it takes some time for
the medium to come back in to that
portion and so for a momentary uh
instant there is a creation of a low
pressure Zone which creates the pull of
the Melt pool which has been formulated
and that's how you remove the material
in this particular process so it's a
useful tool electrod disar Machining
just as like electrochemical Machining
now I'm going to uh give this details of
the modeling process Etc in later on
lectures but here from a standpoint of
what EDM can do you can look at some of
the components High aspect ratio systems
you know examples uh here are for
example um you can have these small
cavities uh or this
gearings produced by
the EDM process or the electro
electrical discharge Machining process
so for example here there are two round
Parts here and the set of dieses for
extruding the aluminum the aluminum
piece is shown in the front so this is
the piece and this is the Dy these are
the dyes which are uh used for extruding
this particular piece so such examples
are very common place where EDM is used
for this applications this for example
is another uh illustration where there
is a work piece made the um anode and
the electrode made the cathode and uh
there is a spiral cavity being produced
okay
uh
by either ECM or EDM type of operations
so uh having said
that a slight variant of this process uh
is found in
uh very common place and very handy uh
tool for having complex shapes like L
slots or Cam profiles being cut and this
is called wire cut EDM okay and
typically a process is uh driven by a
CNC uh system so we that's why we call
it CNC wire cut
EDM
so essentially uh what it means is that
you have a coordinate layout which is
there and then between the coordinates U
there is movement of the uh particular
tool okay and that creates its uh
Machining effect on the work piece in
this particular uh case there is a work
work piece uh typic which is made the
anode okay so the work piece is made the
anode and there is a supply dialectric
Supply uh supply of dialectric fluid
insulating fluid in the work Zone and
there is a wire and this wire is
normally made the cathode okay so the
wire actually is fed from a roll you can
see uh between this roll here and this
roll here the wire is being fed and as
the wire slowly eminates out um it there
is a discharge which happens between the
wire the cathode and the work piece
anode and wherever the wire moves so
this slot right here uh is an L slot
which is otherwise seen in the top view
so the wire actually the motion of the
wire path would be first in this
direction and then in this direction so
the wire comes all the way into this and
then goes like this and wherever the
wire proceeds there is a arcing because
of which this complex L slot depending
on the path or the guide of the wire uh
would formulate on the work piece so
this is a very interesting High
capability process uh which uh is uh uh
used in the domain of advanced
manufacturing processes for uh doing
extremely complex shapes and features
and I'd just like to recall that if we
are talking about micro gearing or if we
are talking about
um very small features of high aspect
ratio there is a possibility that if the
stage itself which is feeding the wire
in this particular case the wire being
about close to 80 Micron diameter or so
uh if the stage has a fine resolution of
movement then you can actually uh be
able to make small features or
components uh utilizing the effect of
such small motions such Precision
motions of the stage itself so the stage
needs to be very fine-tuned so this is
how a wire cut EDM system looks like in
the laboratory this right here is that
wire okay and it is uh passed between
the roles one role can be seen here the
other role is probably out of uh the
picture and
uh there is a way to mount the work
piece in this particular case which
gives uh the basis of uh
EDM so let us now look at some of the
uh micro
structuring being uh done by wire micro
EDM operations uh some very nice
illustrations by benavites group in 2002
uh where he talks about the creation of
a small U ratchet wheel okay with
diameter of with the teeth thickness of
about close to 250 microns in burum
Copper
U so the way to make it is that uh they
take a blank and then turn the blank on
a high Precision L and uh
uh are able to structure it in a manner
so that there is a cup at the center
here and then my other fine operations
like drilling Etc uh these
mounting holes or
uh the center
mounting of these blank is being uh
formulated once this is formulated they
use a wire here this right here is the
wire between the two tick marks okay and
they perform a micro wire EDM on of all
possible teeth at the three levels of
this uh blank the blanks are cut into
three different levels as can be
Illustrated
here and
uh basically you can also use another
electrode uh for removing
the teeth from each other so once the
blank has been formulated in three
already some Machining has been done
here but the extent to which the machine
can go is very limited in the the radial
Direction in this particular case
okay and uh
therefore um the tooth removing
electrode sort of cleaves it diametrally
so the electrode goes all the way to the
other side here and Cleaves it
diametrally so that three
pieces can be realized which are
independent
discs with micro
gearing cut on each of
them so the wire micro EDM machine
fabricates all the Ratchet teeths on
each of the three levels and uh the
final operation requires the removal of
the ratchet teeth including a uh missing
tooth in the middle level that is
obscured directly
above and directly below uh by teeth
that are not
removed so this right here shows a
detailed view SCM image of the wire
micro EDM ratchet teeth structure and uh
this is in nitronic 60 stainless steel
and uh they have also done it for
titanium allers and they have seen that
the process is quite favorable for
titanium Machining titanium allo also um
by micro ym so this is a very highly
capable process now for uh doing these
micro features and structures so you can
imagine the ratchet teeth thickness of
250 means uh this one section here okay
is only 20 50 micrometer thick and there
are three such sections and different
levels of this particular
mechanism so this is one very fine
example of what uh cncm can do apart
from that there are many other
applications of the micro EDM process um
one of the examples here shows a
machined complex micro cavity consisting
of a square cavity which is about
480
microns
wide and 480 microns long okay with a
depth of about 40 microns and there is a
small pyramid at the center uh which is
being made by the whole Machining is
being made by a micro EDM operation I
use
a radius of this cylindrical cavity of
the extent of about 200
microns and uh the depth of this cavity
is about 100
microns so and if you look at the
pyramid uh structure the pyramid is
about 120 Micron tall and uh it's a
square pyramid so each side of the
square is about 60 mic microns 60
microns so this comments highly about
the way that EDM or the capability
process capability of um EDM to do 3D
micro structured architectures or
parts figure two again uh is a electrode
a circular electrode the SCM image of a
circular electrode and this tip size
here must be close to
about probably 10 of tens of microns so
this is doable again using micro rum
process this cylindrical electrode was
uh prepared by uh you know a
wire assisted Electro discharge grinding
uh unit the electro discharge Machining
process and uh I think I had Illustrated
further earlier that with another kind
of an identical wire assisted ECM
process we had produced about 2 microns
of tip size in this particular case
although the tip size is slightly higher
uh it's about 5.2 uh micrometer but uh
it still um is a very high improvement
over the other Machining processes uh
which exist figure three here
illustrates a complex uh cavity Machine
by again a micro EDM uh tool the radius
of the spherical cavity in this
particular region is about 150
micrometer okay and the conical cavi is
uh having a top diameter of 240 microns
and a bottom diameter of 20 microns the
depth of about 60 microns and uh this
conical cavity further is connected with
this uh spherical
cavity
so such inverted features in one case
probably this part is through a die
syncing operation uh where the tool is a
negative replica of this or it's a
cavity and in this particular case the
tool is a projection coming out of the
tool surface they can be done uh
parallell on a Surface so that's the
capability of producing a
three-dimensional structured highly
structured surface of uh at the
microscopic lens scale and such uh kind
of operations demonstrate the capability
of the microed M process micro Electro
discharge Machining process another uh
you know aspect of EDM uh reported by
uol in 2002 which talks about a high
aspect ratio blind micro hole kind of
structures these are the micro hole
structures and the holes can be either
triangular holes or square holes or even
pentagonal holes depending on the uh
electrode that is being used okay and
this is using planetary movement
approach okay of the tool so the
planetary uh movement is in in in this
case basically uh
smaller electrode moving or following
across the whole the internal Contour of
the hole okay so the planetary movement
of the tool electrode is widely used in
this conventional D syncing EDM
process and one of the reasons why that
is used is to give a sufficient gap for
debris removal will take place and so
the Machining is always stable uh uh
because of non- accumulation of the
debris at any part of the Machining zone
so particularly in cylindrical cases or
in circular cases you can uh really
follow this planetary motion and uh you
can with this uh drill circular micro
holes with high aspect ratio okay of a
rotating
electrode uh
is put inside the uh tool so a similar
kind of um
Machining cannot be done if uh the
holes uh concerned have non circular
cross-sections for example in this case
it's a triangular hole or a square hole
but in that event a square blind micro
Hole uh can be machined by using a
square electrode okay so you just
develop a electrode which is very close
to this and uh maybe a good idea would
be if this square is reasonably small
okay in comparison to the uh square that
is being
Illustrated uh so if in this particular
case as I was saying if the square
electrode is reasonably small it can
follow a square path okay of motion
something like this just as in this case
there was a circular tool which was
following a circular path and even you
could have rotated the tool while
following it the square tool can also
follow a square path and that would give
you a very good Machining operation in
this case for example there can be a
triangle a small triangle and this
triangle can follow a triangular path
okay so that this whole thing can be
machined accordingly so uh there are
different strategies that now people use
for doing this uh micro ADM with
planetary movement or planetary motion
okay um in fact all these holes are to
the depth of about 2500 micromet and in
fact if you look at one of these edges
here or for example this particular Edge
they must be close to if this is 10
microns this must be close close to
about 130 or 140 microns okay so having
said that uh a very good aspect ratio of
the order of about uh close to 18 or so
uh is generated uh using uh this kind of
a process so it's actually a very good
and capable process for doing High
aspect ratio structures at the Micron
scale so if you had no planetary
movement for example if this same
process would have been produced by a
normal electrode of the same size as the
whole Etc the aspect ratio would then
come to about close to 10 okay so in a
way it illustrates what the planetary
motion does uh in terms of debris
removal where uh the activity can be
prolonged over a higher amount of depth
so that the ACT ratio can increase
accordingly so in 3D micro Machining
particularly when we are talking about
large aspect ratio structures definitely
the planetary EDM micro EDM is a very
good strategy uh to manufacture at this
particular scale of the length Let's uh
look at some more examples uh and uh
when just because we were talking about
aspect ratio uh I uh would recall the
Liga process which we had discussed
earlier while doing the microfabrication
and this Liga uh process basically means
lithography uh Galvan Aur okay and there
is a detailed step of the Liga process
probably in the next slide we'll just
recall some of that before going ahead
but this is a combination in this
particular slide
as uh proposed by takahata at all in
2000 uh this uh is is a case where micro
EDM is being performed by combining it
with a Liga process okay so as you can
see here there are various steps just
like liography you have a pmma layer
which is exposed to x-ray through a
masking process and this um ultimately
we want to produce these features right
here okay so these are sort of um
negatives of micro gearings okay which
are produced in a high depth manner so
in the first step what happens is that
this mask is realized using either laser
patterning or some other method with
which this a small structure here gear
like structure can be uh made as
openings typically as openings okay so
the mask has
openings in
the shape of
micro internal
gearings these are internal
gearings as can be Illustrated now if
you look at the printing resolution of
these gears the internal gearings are of
the diameter of something like close to
200 microns okay and they are distantly
placed away from each other by close to
about 1 mm or so so you take a resist
pmma and using xra
lithography uh why we need xra
lithography because uh x-rays are
typically high energy radiations and
they can go up to a larger depth within
the pmma material so in this case it is
needed that the uh depth up to which the
internal gearing should go on that layer
is about 300 microns or so okay so that
is why it is needed uh so you take a uh
mask and expose the pmma select itively
so you're exposing the pmma selectively
here and uh you are exposing up
to you know a height of or a depth of
about 300 microns of diameters of
internal gearings which are only 200
microns in nature so it's the aspect
ratio is about 1.5 in this particular
case now the pmma is changed as soon as
it gets exposed to certain uh region so
supposing if you were to expose this
region which now you can see converted
as this Hatchet area in this uh
particular uh case the uh structure the
properties of pmma here has changed and
uh you can develop these pmma uh exposed
pmma out uh very well okay using uh some
kind of a development solution Etc and
so
therefore there are these crevices which
has
formulated uh on the pmma itself
so you can actually do electr plating of
this um
cavities and then after electr plating
you can planarize and uh polish on both
sides so that you are left with only
those features which have been embedded
inside the pmma as uh electroplated
features and the uh electroplating is
done using this substrate here which is
uh uh a conducting substrate that you
should always remember conducting
substrate okay and there is always a
deposition of platinum along the
uh along the crevice which has been
created here of 300 microns okay so it
is all deposited along this whole
crevice as well as on the conducting
substrate here the substrate is later on
removed as in this particular case you
can see the substrate is actually has
been removed uh and the conducting
substrate is gone uh from here here and
you have now cavities like Illustrated
here open on both ends which can be used
for further Machining so now the
advantage here is that these cavities
are already pre-coded with Platinum
right so they are pre-coded with
Platinum they're platinized and they are
like metallic in nature so they can May
made an electrode so typically in this
case if you want to do EDM operation
this is made the cathode okay and uh uh
the work piece in this case has a size
which is close to the hole that can be
seen here okay and uh the workpiece is
made the anode so this work piece is
positive and uh this is the cathode
negative and so uh the work piece which
was otherwise a cylinder is now cut into
a gear which is SC the SC image of which
is shown here so this is the micro
EDM work piece the advantage in this
case and uh finally the cross-sectional
area of this electrode looks as
beautiful as this where uh you have to
ensure that a gap of about 3 microns is
always there between the electrode and
the EDM gear so that is more about
process setting and probably the
monitoring of the Gap current value okay
so with the CNC control you can do that
kind of a feed rate of this micro
gearing into this particular structure
so this is about the capability of um
High spect ratio micro
structures uh in combination with
various processes like Liga Etc these
are some other examples again you know
you can see how I aspect ratio uh
structures can be developed by um
microwire EDM using the same concept of
Liga plus edms has been Illustrated
before these are pillars of Dimensions
80 to 525
microns
um in in length scale so 80 microns is
the uh breadth or the thickness of the
pillars and the uh 20 525 microns is the
depth of the pillars and these pillars
are being printed at 400 Micron depth so
they are very high aspect ratio
structures which can only be obtained
through this specialized process this
again is a steel gear assembly okay it's
a steel gear wheel cut it uh with the 20
Micron tungsten wire okay and uh this is
with one trim using the CNC wire cut
process EDM process as had been uh
Illustrated earlier and uh the gear
wheel has only an outer diameter of only
about 500 Micron so that's how small
this gear is and a height of about 6 mm
so you can think of the high aspect
ratio that is involved in this kind of a
structure and you can
see the number number of teeth in this
particular case is eight okay so there
are about eight teeth uh made in this uh
gearing so such is the power of this 3D
uh novel 3D micr structuring process
again another very good example of U uh
again a ceramic uh gear wheel okay the
height is 10 mm and the OD is about 1 mm
number of teeth are eight in this
particular case again in for micro fuel
cell applications uh scuol has shown
very small channels increased with
increased um exchanging surface for
hydrogen oxygen reaction to take place
in fuel cells okay and
so this uh illustrates a carbon paper
fiber
uh microfuel cell and uh the channel
sizes are about close to 500 microns
area is only 15 to 25 mm Square the
tungsten wire that is used in these
applications is only about 500
micrometers uh uh long diameter so
that's again another very good
illustration of what micro wire EDM can
do I'll just briefly illustrate as I
promised the Liga process and uh because
you know it is important in a way that
Liga is combined with the EDM to make
many useful features so here for example
uh there are different steps in a Liga
so just like lithography you irradiate
the resist here uh with the mask here
the word IMT is written as uh portions
which are black and portions which are
transparent this typically means that
the portions which are blank are uh or
or or transparent are uh beam
transparent and the portions which are
indicated as black are actually beam
opaque so they are stopping the X-ray
beams from going into the resist so
wherever there is non-exposure there is
a retention of the resist so the IMT
gets retained here and then you can
actually electroform by depositing metal
on this particular
uh uh set of words formulated at the
Micron scale and uh then you can strip
off the uh unirradiated
resist okay uh and it's because of that
the portion of the resist which has not
been irradiated which is actually here
uh this is made on that resist by the
way um so when this gets removed then
you can actually have these IMT
structures or features coming out okay
uh in this demolding process and then
you can do a secondary electroforming
process also to make uh plastic or metal
uh sheets out of it so that's why it's
called galvano foring up foring okay so
there is a forming which is involved
there is a galvanic coating of the
material which is involved using a metal
substrate in this case this substrate
here is actually metal for doing this
coating and then there is also
lithography involved by using high
energy x-ray beams so uh this is a very
good process uh illustrated by BL at
Hall uh in science reviews uh some time
back this this slide has been borrowed
from his paper actually and uh there are
a lot of applications that Liga has to
offer this is a nickel honeycomb
structure for example fabricated on
processed silicon wafer and uh this has
been obtained by again Liga
process uh where uh the the initial
process was hot embossing driven but
then later on electr forming was used
okay and uh the width of the walls in
this case are about 8 microns height is
about 100 microns similarly these are
Liam made nickel microscale structures
with different shapes in the Third
Dimension the total height is about
close to 500 uh 20 microns
similarly uh there has been reports made
by BL at all about different uh uh
electrostatically made Liga nickel micro
Motors or micro turbin as can be seen
very clearly in these particular figures
where the uh diameter of the micr
turbine in this case is only about 130
microns and the height is about 150 mic
higher than the diameter so it's a large
diameter uh High aspect ratio structure
and uh you know if you really test this
uh turbine it can generate about 10 the^
of 8 rotations okay uh that's how about
the uh lifetime is of this turbine and
the revolution that it can go up to is
very high of the range of about 150,000
RPM okay so such is the beauty about
these micro machined microscale
processes
uh with electrostatic Lia again you have
made the people have reported this micro
motor uh which is made with a two3 rotor
of diameter 700 microns and Staters this
is the stator part okay uh with the
wheel D of approximately 250 microns for
torque transmission and uh you can
actually get the power of this motor
through this small pinion wheel and this
can rotate at a very very high RPM and
the scale on only is few microns so you
can imagine the kind of power
RPM ratios that can be obtained at this
particular scale again another very
important example that Liga has to offer
you can make micr Channel arrays with a
high aspect ratio of close to 12 okay uh
here there these are three dimensional
micro structures again micro column
array and well arrays micro groupes with
curvatures uh some of these uh
micro structures with high aspect ratios
of about 30 or more and then these are
the micro lens arrays all made with Liga
processes as reported by wangal in 2001
so Liga really is a very powerful tool
so I'm going to now illustrate a little
bit about the ecdm process because
naturally we have talked about high
aspect ratio by combining Liga with EDM
and uh you know these hybrid processes
always seem to work better than the nor
normal routine processes and uh ecdm is
such a process where the power of both
the EDM and ECM are combined in one go
together and for that I would like to
just illustrate that uh you know if this
is the electrode supposing in ECM
operation and there is a work piece here
okay close to it and the electrode as
you know is made the
um cathode and the work piece is made
the anode and supposing there is an
electrolyte instead of of a dialectric
fluid which comes into this region which
starts the gasification process okay so
there is some gas bubbles which are
generated close to both the work pieces
as a result of which there is a gas film
which
develops between the anode and the
cathode so this leads to uh the
formulation of a insulating gas layer I
would say
and uh again the concept of discharge
may come in here as was Illustrated in
case of EDM before so there is a
discharge which happens because the
breakdown uh of the you know the the
electrical breakdown of the gas-like
medium and the film actually gives way
to a path of an
electrons to the current by by making a
path of electrons by making a path to
the flowing electrons to flow between
the cathode and the anode and it is by
thermal ablation that eventually the
bulk material is removed and then if ECM
is still going on in the same uh in the
same region there is going to be a
self-leveling activity done by ECM after
the EDM operation is done so it's a
combination of ECM and EDM which is
actually known as electrochemical
discharge
Machining and this Machining uh has been
able to demonstrate a much smoother
surface than normally the EDM or ECM
Standalone and not only that this can be
done on brittle and hard and insulating
substrates
also so this is the beauty of this ecdm
process and I'm going to just uh give a
few examples where ECM and EDM are
combined together for giving certain you
know uh Machining certain non-conducting
ceramic materials for example in this
particular case you can see there's a
ecdm process uh which has been able to
carve out a small complex
feature in a ceramic work sample okay
and this typically is machined at 90
volts uh
with a solution of sodium hydroxide
25% and uh although the mrr is very low
at high voltage and high electrolyte
concentration mrr is something which can
be achieved probably by varying the
various uh concentration voltage values
and
U uh the thing which is uh important for
me to tell here is that at a higher uh
elect
concentration uh there is a increasing
uh overcut in the machine okay and the
uh accuracy of the machined surface
varies at a higher concentration so
typically people prefer either medium or
lower concentrations of electrolytes in
this ecdm case Okay this again is a
illustration of uh it's a micrograph of
a machined hole in a ceramic work sample
machined at 80 volts 25% NaOH
electrolyte there are some other
examples alike of ecdm processes where
in pyx glass people have used um ecdm
micro Milling okay so there is a dis
type motion here of a uh tool which is
actually rotated at a uh very high RPM
200 RPM or so and which actually creates
this discharge Machining the chemical
electrochemical discharge Machining
happen between the substrate okay and uh
the tool
and uh in this particular illustration
you can see some beautiful images of
channels being produced okay of uh at
the SC images of channels being produced
at a pulse on time of roughly about 2
milliseconds okay and uh the tool
travels in this case at a constant
travel rate of 100 micrometers per
minute so the process is little slow in
terms of the yield of the uh the
Machining removal rate Etc and uh the
tool diameter in this case which has
been used as a cylinder of about 200
micrometer diameter so I think I am
towards the end of this lecture and uh
we have covered more or less the
applications related to ECM EDM and a
combination hybrid process of a Liga and
EDM as well as ECM EDM called ecdm okay
so in the next module we are going to uh
work more on the process details related
to the electro discharge Machining
operation and try to model the process
from a physics point of view thank
[Music]
[Music]
[Music]
you
