【UVレジン】夜空に浮かぶ星座を閉じ込めた球体をつくる / 星座の作り方

maaue resin channel
22 フォロワー
キラキラと夜空で輝く星座を球体に閉じ込めてみました🌌✨
意外と簡単に作れるので、レジン初心者の方にも是非チャレンジしていただきたいです🙌!
お好きな星座で作れるので、推しの概念を身につけるのにもどうぞ...🥰
#resin #DIY #resinart #resincrafts #howtomake #resincrafts
【twitter】
更新予定の作品を動画より先にちょびっと公開したり、動画のお休みを告知したり...🐱
https://twitter.com/maaaue_resin
【Instagram】
https://www.instagram.com/maaue.no.resin/
【使用したもの】
星の雫(パジコ):https://amzn.to/3rAGyws
REJICO https://amzn.to/3rgNSgJ
モールド https://amzn.to/3u1vKuc
レジン着色剤 https://amzn.to/3FkR2oM
ワイヤー(100均、セリア)
【BGM】
PeriTune様
https://peritune.com/blog/2020/01/04/poema/
下記のリストよりご支援いただけますと嬉しいです🙏✨
作品制作に活用させていただきます!
amazonほしい物リスト:https://www.amazon.jp/hz/wishlist/ls/3DB01MRMLXIUM?ref_=wl_share
Hello, I'm maaue.
In this video, I will show you how to make a starry night with constellation from resin.
This is surprisingly easy to make, so even if you're a resin beginner, I highly recommend trying it.
First, prepare a mold for color mixing, and remove dust from the mold with masking tape.
Put in clear resin.
You only need a small amount on one side.
This time, I will color them blue and purple.
Stir thoroughly.
I'll add a little bit of glitter.
To avoid adding too much glitter, mix in a small amount of glitter after applying it to the mold edge.
After mixing thoroughly, remove the air bubbles with use an embossing heater.
After the air bubbles have disappeared, let it cool down a little.
I will use this 20mm diameter hemisphere mold this time. You can use any size of mold you like.
Remove dust form the mold with masking tape.
Next, put the colored resin in the mold.
Fill up to 60% of the mold.
Only a small amount of purple is needed.
Mix it a little with a toothpick.
Remove the remaining air bubbles.
Cure it.
Fill the mold about 90% with clear resin.
Like this.
Put a small amount of clear resin.
Spread a thin layer of resin.
I will use this 0.8mm diameter brion.
Place the brions in the position of the star of the constellation you want to create.
Arrange them as close to the center to avoid going too far to the edges.
Like this.
I will use 0.3mm wire.
Cut the wire to a length of about 3mm.
Place the wires to connect the brions.
Once you've decided where you want to put the wire, the wires are removed.
Apply clear resin to the position where the wires will be placed.
Place the wires and adjust their positions.
I made a constellation in the middle of the hemisphere like this.
Cover the surface with a thick layer of clear resin.
Remove air bubbles carefully.
Prepare a flat mold and use masking tape to remove dust.
Gently put the flat side on top of the hemisphere.
It seems to be curing well.
Make hemispheres of the same size using clear resin.
Remove air bubbles.
Gently put the flat side on top of the hemisphere.
Remove burrs.
Scrape off any small burrs.
The burrs were cleaned off.
Prepare the hemisphere mold.
Apply clear resin to the hemisphere.
Apply clear resin to another hemisphere.
Assemble the hemispheres together to form a sphere, being careful not to get air bubbles in them.
Put the hemispheres into the hemisphere mold.
Adjust the hemispheres so that they form a sphere.
Fill the gap with clear resin.
Scrape it off and make it as spherical as possible.
Make a hole with a pin vice.
I washed it with water to remove the dust.
Attach the heaton with clear resin.
Hold the heaton with a flat plier, and fasten the handle with a rubber band.
Prepare a clear resin for coating. Heat it up with an embossing heater.
Resin becomes smooth when warmed, which prevents over-coating and uneven application.
Coat the sphere with this resin.
Remove excess resin and make sure that the resin is evenly applied to the entire surface before curing.
Let it cure for about a minute, turning it around and around.
Cure for an additional 2 minutes without turning it.
Nicely done. It looks beautiful constellations in the night sky.
The constellations look this big even if they are made small.
Here is the one that I made with a sphere mold instead of a hemisphere mold. The process is basically the same as the hemisphere mold.
The result is a little nicer because there are no lines caused by bonding the hemispheres together.
I would appreciate it if you could press "like".
Thank you for watching !
