noc19-ph02 Lecture 72-Donor and acceptor energy levels in a semiconductor

IIT Kanpur July 201
20 followers
Dec 3, 2023
[Music]
[Music]
in the previous lecture I derived the
formula for the concentration of
electrons and holes in intrinsic
semiconductors by intrinsic we mean
those where are though where there are
no impurities so that the number of
holes and number of electrons is the
same and we also obtained and this is
the result I need from this lecture
onwards that the product of the number
of electrons
obviously in conduction band and
number of holes in the valence band is
dependent only on temperature so the
result that we obtained was that number
of electrons n times the number of holes
H is equal to four Emmy star M H star
times KB T over 2 pi H cross square
raise to 3 e raised to minus Delta e gap
over KBT and there is a 3x2 in front of
em e star at M H star now notice that
the product is independent independent
of the
Fermi energy epsilon F this is related
to something called the law of mass
action through which we will now
understand that this product should be
dependent only on temperature so
irrespective of where the Fermi level is
that means whether I dope the
semiconductor whether I put some
impurities by and as a consequence shift
as Fermi level or don't dope it this
product is going to remain the same and
this will come in handy so let me just
get this result from the law of mass
action also so it says that if I have
these two levels EC evie the conduction
band on top and the valance band at the
bottom and at temperature T
the rate of production of number of
electrons in the conduction band would
be a function of temperature alone
because higher the temperature more the
photons out here that will excite these
electrons to the conduction band on the
other hand the electrons will also
recombine electrons will recombine with
the holes and therefore there will be a
reduction because of that in the number
of electrons DN by DT because of that
will be equal to minus to show that the
number of electrons is decreasing some
function of temperature times number of
electrons times number of holes if the
product of number of electrons and
number of holes is larger recombination
rate will go up and therefore DN by DT
net will be equal to 80 minus bt n times
NH and at steady state when everything
is time independent for steady state DN
by DT will be 0 and this implies in this
case n times n H will be 80 over V T
which is a function of temperature alone
so no matter where these holes and
electrons are being generated from
whether from some impurity levels
whether from some valence band the
product of n times n holes is going to
remain unchanged and it will depend only
on temperature so I argued from the law
of mass action also this should be so
and we indeed see it now what I am going
to talk about in this lecture is
the donor and acceptor levels in
semiconductors
so let me explain what that is you see
the usefulness of semiconductors arises
from the fact that one by temperature
variation the charge carriers can vary
quite a lot they actually change
exponentially the dependence of the
number of electrons is proportional to e
raised to minus Delta e over KBT to KBT
and therefore as you change the
temperature things change exponentially
so it's very sensitive to the
temperature you can use it to make
thermometers you can make use it to
sense the change in temperature anywhere
the other thing is that you can change
the conductivity also or the the second
thing is that you can also change the
number of charge carriers by putting
some impurities in the system and those
are known as donors or acceptors
depending on what they do
so these impurities are the impurities
either have an extra electron or they
have have a deficit of
one electron depending on what they are
you know they're called either donor or
acceptors so if you have an extra
electron so for example these will be
called donors and these will be called
acceptors and rightly so because a
impurity that has an extra electron
gives it to the system and that electron
goes into the conduction band a an
impurity that has a deficit of one
electron accepts one electron from the
system and therefore creates a hole at
the top of the valence band typical
examples for silicon based device or so
if I take intrinsic semiconductor a
silicon or germanium then the donors
would be for example phosphorus there's
fifteen electrons and an acceptor would
be boron or aluminum so they act as
creator of electrons or creator of holes
and therefore I can have two kinds of
semiconductors so first thing that we
want to know is what are the energies of
an electron or a hole
given by these impurities so let us
first look at the donor so look at this
suppose I have these silicon atoms
and I put a donor atom here phosphorus
and typically the density of these
impurities donors or acceptors are one
in a million you don't want to change
things much but you still want to have
the control on the charge density so now
this has an extra electron this has an
extra electron the rest of the things
roughly remain the same so what would
happen to this electron is it will go
into the conduction band because the
band so we're talking about zero
temperatures of band valence band is
completely filled and this extra
electron comes here we let move around
freely in the band that's the next
question right will the extra electron
move freely in the band there's the next
question and the answer is no what
happens is that when this extra electron
comes out so let me show you this by red
color it is moving around but then it is
left a positive charge on this impurity
ion phosphorous and this positive charge
is going to attract it
so it's going to be bound to this
although Italy move around but it will
state remain bound and that binding is
gives you something called the donor
energy level so let's see how do I
calculate this since the impurity is low
you know I have all these silicon atoms
and then in the middle I have this
positive charge and an electron in this
medium I'm going to make an
approximation that the collection of SI
atoms is being treated like a continuous
medium so in that sense I'm not taking
the graininess of this into account so
the problem I have now is that an
electron is moving around a positive
charge center in a potential V R which
is 1 over 4 PI epsilon zero e square
over R the minus sign in front but there
is a epsilon R here epsilon R is the
dielectric constant
of Si or the host system and the mass of
electron because it's moving in this
band is its effective mass so the
problem I have to calculate this energy
of this electron bound to the system is
that it is an electron moving around a
unit positive charge with the potential
being given as e square by 4 PI epsilon
0 epsilon relative R and the kinetic
energy is minus H cross square over 2 m
e star del square so the Hamiltonian of
this electron in this medium is minus H
Cross's square over 2 m e star del
square minus 1 over 4 PI epsilon zero e
square upon epsilon relative R this is
exactly the hydrogen atom problem you
could even solve for the energy levels
using Bohr model and therefore the
energy that you're going to get en is
going to be minus 13 point 6 e V and
this will be scaled by this dielectric
constant epsilon relative square times M
e star divided by M e right because I
replaced the mass of the electron by
mass of the effective mass of the
electron and therefore that ratio comes
in the energy and energy also depends on
the electronic charge as I raise to 4
and therefore I get a power of ER square
in the denominator and this and 1 over n
square now radius of this electron is
also going to be equal to M e epsilon
relative over m e
star times the Bohr radius n square so
you see the radius goes bigger by a
factor of Amy by Amy star times the
dielectric constant that makes sense
because now the potential is weaker
because of the dielectric constant mass
is lighter so electron moves in a much
larger radius if mass is heavier it will
be less so you can see now for typically
for say silicon or such materials
epsilon relative is of the order of 10
and Emmy star is of the order of 0.1 m
electron and therefore you get en of the
order of minus thirteen point six
divided by 1000 C of the order of MeV
and RN is of the order of 100 a zero for
the ground state
so the energy of the donor level is
really small of the order of MeV and
radius has become roughly 100 times the
hydrogen atom rate radius so you can see
that our continuum model that is the
approximation we made that I can treat
the silicon atoms distributed as a
continuous medium is justified when I
look at RN because it comes out to be
about 100 atomic radius so it will carry
about a thousand silicon atoms which is
like bulk so in a self-consistent way
are justified using the the
approximation for treating silicon as
continuous and energy is reduced so what
is happening now therefore is that this
electron which have would have moved in
the conduction band here freely instead
of moving there it it is bound to this
donor atom by roughly an energy Delta e
donor which is equal to EC minus e donor
level and there would be other levels
lower than this one over n square but we
are neglecting those this is the main
level this is known as donor level
similarly if I have an acceptor atom
an acceptor atom what would happen is I
have these silicon atoms
and then let's say I have a boron which
has five electrons that Regina had the
silicon
this has one less electron so therefore
when I look at this valence band it will
be less by one electron so do the rest
of the electrons move around yes they
will move around you know so the
electrons are out moving around but
remember our picture of the hole when
rest of the electrons are moving around
if they come around boron they have left
a positive charge behind on the silicon
either on this silicon or on the silicon
or on the silicon and this has become a
negative iron boron would have become a
negative ion so in terms of hole I would
make a picture that this hole out here
is moving around the negative Center
it's exactly like it hydrogen atom
problem except now the roles of positive
and negative charges are reversed
therefore the energy of the hole would
also be given as minus thirteen point
six over epsilon Epsilon relative square
which is same for both electrons and and
holes and I'll have em whole star over
em II instead of any star over a me for
the whole energy
again they call our discussion from hole
if this is the valence band the whole
band goes the other way - II and what we
are saying is below this are these
executive levels in terms of only
electron picture I would make this
valence band and these are the acceptor
levels this hole is in the valence band
and it requires some energy before the
hole can go to the acceptor level so
these are known as acceptor levels we
make these pictures of course in the
bands for electrons so therefore they
are made like this so the complete
picture that emerges if a semi conductor
has both donor and the acceptor levels
let me draw a line here to differentiate
I'm going to have a donor level here and
an acceptor level here and what Li let
me make this picture better on the next
slide here I have the conduction band
here I have the valence band and I would
have the acceptor level here and
this Delta II donor is equal to minus
thirteen point six over epsilon relative
square em e star over free electron mass
and Delta e acceptor is minus thirteen
point six over epsilon R square em whole
star over m e now I see instead of an
electron that had to cross this barrier
of Delta e gap which is of the order of
electron volts now an electron from an
acceptor level or a donor level can
easily cross over to the conduction band
so these will populate the conduction
band and in the acceptor level these
electrons can go up here to the acceptor
level and create lot of holes here so by
doping and intrinsic semiconductor we
can increase the electron concentration
in the conduction band if the electron
concentration goes up because n times n
hole is constant it depends only on the
temperature the hole concentration will
come down and these are known as n-type
semiconductors or increase the hole
concentration
in the valence band
what are known as p-type semiconductors
and if I increase the number of holes
number of electrons in the conduction
band will go down so majority carriers
in n-type are going to be electrons and
majority carriers in p-type
semiconductors are going to be holes so
to conclude this lecture we see that
dope ends create donor or acceptor
levels in a otherwise intrinsic
semiconductor so if you put them they
create these levels and therefore make a
semiconductor either n-type
so in this electrons are the majority
current errors or p-type holes are they
majority current carriers and this
increase in the number of electrons on
number of holes comes because Delta II
donor or Delta II acceptor is much much
much less than Delta II gap so it gives
us a fantastic control on the material
as to what kind I want to make it and
how I wish to use it in the next lecture
we will calculate the concentrations of
electrons and holes and see how they
affect the properties of semiconductors
when they are doped thank you
[Music]
[Music]
[Music]
