noc20-ce19-lec18

IIT Kanpur July 201
20 followers
1 Video View·Dec 3, 2023
Welcome back. So, in previous lecture mainly we discussed about the how to identify or
locate the epicenter of different earthquakes. So, if you are having 3 stations maximum you
can identify or locate the epicenter of any particular earthquake. And then we also discussed
about that what are the symbols what we are talking about the pitch and ball diagrams
which are indicating of different faulting. So, we have normal fault, reverse fault and
the strikes default. So, I will not go into the detail of the faults which have been given
here, but to just have a brief introduction about this. In this case what we see is an extension
when the hanging wall on the left hand side moves down along the inclined fault plane.
And in case of the reverse fault the hanging wall moves up in case of along the fault plane
inclined fault plane. So, this is an compressional tectonic environment this is an extension
tectonic environment. And whereas, this one the third one is in
strikes default where one block moves away from or just passed each other with respect
to the default point here. So, in this case what we see is the right hand side block is
moving towards us and the left hand side is moving away from us. So, this is we termed
as an right lateral strike strike. About the features what we see on the surface
we will talk when we are we will start talking about the active faults and active fault topography.
And the respective symbols are been given here. So, usually in the map after the earthquake
such figures or the symbols will be available which indicates that what type of earthquake.
Now, moving further we also had brief discussion about that the if the earthquakes distribution
of the earthquakes. And now coming to the recurrence of earthquake due to stress developed
by tectonic forces. Now, this before getting into the example of 2001 Bhuj earthquake I
will just briefly tell you that why what are the reasons for the triggered earthquakes
or the triggered stresses on different faults because of the because of an earthquake.
So, triggered stresses mainly we say that the small part of stresses are released which
were accumulated slowly when the earth's plate moved towards or passed each other. So,
this also indicate that not all the stress or the energy which was been accumulated got
released during a single event, but there is some left out stress which is which can
trigger the earthquake in near future or you can say that the release of energy at on a
particular fault has triggered the earthquake on another one.
So, usually this has been taken into consideration that if a stress is released on a particular
fault during a particular earthquake, then there will be an drop in stress on that particular
fault. So, that means, that the next earthquake on that fault will not reoccur until this
stress repels and it crosses the threshold limit. And typically this the time duration
which has been taken to rebuild the stress may vary from hundreds to thousands of years.
So, in case of the areas which are close to the plate boundaries will have lesser interval
or that the recurrence interval whereas, the areas which are sitting away from the plate
boundary will have the larger recurrence interval. So, this is usually has been considered that
once the earthquake has occurred on a particular fault, then there will be an drop in stress
pattern, but and it will remain quite until the until the next event because this requires
the rebuilding of the stress on that particular fault, but an earthquake will occur elsewhere
at this site other than the slip fault. So, in this case what we can we can conclude
is that though the earthquake has occurred in particular area. For example, in one of
the slide I was talking about that there was 1905 earthquake, then there was 1934 and then
we had 1950 this is in case of Himalayas. So, we what we discussed in during that time
was that this portion which has not triggered any earthquake will form like will indicate
a sort of in seismic gap. It is quite possible that we mean this earthquake was triggered
on one of the fault system which exist in the region and the another fault system which
is sitting in that particular area can host an earthquake. So, this what is been discussed
here that the earthquake will reoccur elsewhere and not on the particular fault, but the area
may be the same. So, the area where the stress is building up will be the site for the next
earthquakes to occur both as small as well as the large one.
Now, in case of the recent earthquake of 2001 Bhuj earthquake, what we observed was of course,
the concentration of the earthquakes that is aftershocks were confined to this region
and that indicate the rupture area, but there was sudden increase in the seismicity in this
particular region ok. So, earthquake was triggered here, but we saw that number of earthquakes
small magnitude earthquakes micro earthquakes were triggered and few small magnitude earthquakes
which were greater than 5 were triggered further north along could be along the two active faults
which are named as Gedi fault and South Walgar fault. So, probably the stress which was released
here has triggered the stress which was accumulated in this area and this may host another earthquake
a large magnitude earthquake which we will call as an triggered earthquake.
And similar you know phenomena was been observed in 2015 earthquake which was along the Himalayan
region that was in Gorkha earthquake. So, 2015 was one and then immediately after a month another
earthquake was been triggered which is of which was of similar magnitude and so,
some scientific groups they consider that earthquake as an aftershock, but that could
be a result of an triggered stress on another fault or on the same fault which was left out
that is the stress which was left out might have triggered the another earthquake in that region.
So, sometime because of the large earthquake another large earthquake could be triggered
in the nearby area. So, this part we have already discussed. So, I will just move quickly. So,
locating the fault in which direction it is dipping in which whole area was ruptured this
has been shown in this diagram this is a plan view which shows the distribution of the main
shock or location of the main shock and distribution of the micro seismicity or the
aftershocks and this is been shown in with respect to again the plan view and the depth
which has been plotted. So, this shows that the main shock was triggered at around 25 or 23 to 25
kilometer deep and probably was along the north Vagad fault which is dipping due south,
but in some cases it has been observed that probably this is not the actual plane because
you this is an arbitrary line which has been drawn, but could be the earthquake was on the
Kachchh mainland fault. Now, the classification of the earthquakes on the basis of the focal depth
this we have been talking about that intermediate and shallow and deep earthquakes we discussed when
we were talking about the plate tectonics. So, the focal depth of an earthquake is the
depth from the earth surface to the region where the earthquakes energy originates. So,
this is the point of the focus and exactly on the surface and this point has been termed as
epicenter. So, most of the earthquake occur in the brittle portion of the crust above the brittle
ductile boundary that is the boundary between lithosphere and stenosphere. So, in terms of the
depth if we have to classify the in the broader sense then up to 70 kilometer depth we classify
those earthquakes as shallow earthquakes with depth ranging from 70 to 300 kilometers than
intermediate and deeper earthquakes are having the depth more than 300 to 700 kilometers.
So, this you can refer with the figure which was been shown as an in the case of the Vadati
zone which explains that the whole subducting plate will host the earthquakes and depending
on the depth you can classify those earthquake either they are deep earthquakes,
they are intermediate or shallow earthquakes. Now, we discussed about the seismic waves,
we discussed about the earthquake epicenter which is of course, these are the two important
parameters and in one lecture we talked about the details of the lithology which
plays an important role in terms of seismic shaking. So, after having and brief understanding
of the occurrence of the earthquakes and the depth of the earthquakes then the type of faulting the
geology also plays an important role in seismic hazard. So, if you have the different lithology
for example, it has been shown here that on the left you have hard rocks, igneous rocks or you
can either you can say it is a massive rocks if you are having then you are having sedimentary
rocks and then alluvium and then further finer alluvium here. So, the amplification during
ground shaking will vary from place to place. So, hard rock will have less amplification and
it keep increasing if you move towards the loose material and in sedimentary rock area you will
have comparatively higher amplification because of ground because of the seismic shaking and here in
the case of the alluvium you will have much much larger as compared to the sedimentary rocks and
the massive rocks if you are having. So, the ground acceleration is very much dependent on
the type of sediments and rock types. So, this effect basically is been termed as material
amplification. So, along with the understanding that where exactly our sites are located or site
of our interest or any urban settlement is located whether it is on sedimentary rock,
igneous or metamorphic rock or you are sitting on alluvium depending on that you will have the
the amplification that during the ground shaking. Now, getting into the further detail of the
the seismic wave and its relation with the amplification the frequency of seismic waves
when they say the earthquake is triggered variety of different frequency of seismic waves are
generated. So, the frequency of seismic wave that is body wave and you are having the surface
waves plays a key role in damage pattern. This is this part is the most important one
and this will again depend on the geology of the material that is the geology of the area
what type of material we have at a particular site. So, again along with that that is one part
of the geology, but along with that we have at how far the site is located from the epicenter
ok. Whether it is close or within the zone or it is sitting far away from the epicentral zone.
So, most P and S wave that is your body waves have frequencies ranging from 0.5 to 20 Hertz
and whereas, the surface wave we have the frequency less than 1 Hertz ok. So,
we have the frequencies which are ranging from 0.5 to 20 Hertz we will be able to experience
during an any particular earthquake. So, in and during any earthquake both body waves and P surface
waves will be generated. So, during earthquake wide range of frequencies of seismic waves are
produced. So, shaking results resulted by high frequency wave which are 0.5 to 20 Hertz that is
the that is your body waves and this waves will cause shortened buildings to vibrate.
So, if you are having low story buildings they will vibrate during the body waves which are
generated. So, and the low frequency waves usually your less than 1 Hertz. So, in this case what we
are having the mainly the surface waves and this surface waves will cause high buildings to vibrate.
So, in this case what we can conclude is both shorter building as well as the taller buildings
will vibrate because both body waves and surface waves will be generated during a particular
earthquake. So, it is the shaking or vibration usually causes the damage to the civil structures.
Now, near epicenter both frequencies. So, you have the body wave and the surface wave both
frequencies high and low will be experienced hence both shorter as well as the taller buildings will
be damaged. So, this is in case of the epicentral region while the increasing distance higher
frequency will mostly the P and S waves. So, this will get weakened and the this will die
out at an increasing distance and this process is termed as attenuation. But the low frequency
waves usually what we have like in case of the surface waves that is L and P waves will have
tendency to travel long distance without much of attenuation and this will cause damage to taller
buildings which are located far off. So, what basic thing which we learn the fundamental
thing we learn that in case of your epicentral area you will experience both that is the low
frequency waves and high frequency waves as the body wave and surface waves and that will result
into the damage of shorter building and taller buildings. So, those will be in those buildings
both shorter and taller will be experiencing vibration whereas, the far distance located
areas mostly the low frequency waves will travel without any attenuation and result
into the vibration of the taller buildings. So, these are some catastrophic events which
are been listed here right up to 2010, but we also had the recent earthquake as I was talking
about 2015 in Himalayas. Now, frequency and building vibration if we consider this two
buildings of different height sway at different frequency like inverted pendulum. So, if you are
having the shorter buildings they will sway less whereas, if you are having the taller buildings
you will they will sway or swing we can say and the larger area has been covered ok.
So, this is the comparison which has been given for the shorter building,
mid height buildings and taller buildings. So, buildings with 1 or 2 storey building
oscillates at 5 to 10 hertz, shakes back and forth rapidly with an high frequency.
There is the period of this is basically what we are talking about the sway period which is
around 0.2 second to 1 second whereas, in the case of this one this will be higher and in case of this
one that is your taller buildings it will be comparatively higher. So, mostly if you are
having the buildings which are having the open storey and the ground storey is an open on the
open storey or we can say on just on the columns and they will have chances of getting damage very
soon ok because the the movement will result into the sway of the building.
So, if they are been tied up by this members then the diagonal members then they may stay or
withstand the earthquake ground shaking, but if you are having this type of buildings when most
of the cities we see that the the ground floor has been used for garages ok and that will result
into the collapse of this portion. Similarly, if you are having the 2 rigid portions of the
building and in between you are having many windows and those regions will also act as a
weak zone and will result into the damage ok. So, a weak zone a weak ground floor without
diagonal braces ah will result into failure and this is the example of that the collapse
of the ground floor ah which are unbraced a ground floor garages very much similar to
what is been shown here. So, this is another case of the many windows
which are been which were been located here in between the 2 massive portion of the building
and whereas, this did not suffer anything because this was all having the the walls here not the
just the columns. So, the weaker floor ah was this which collapsed. So, in most of the areas
ah there is a retrofit has been done putting the diagonal braces ah to withstand the earthquake
shaking and this fashion. So, of course, this ah this is not very aesthetic in the sense of
the beauty of the building, but the more most important is to save this building from an
earthquake because again this whole area is ah with windows. So, this diagonal braces
ah will act as an protector during the ground shaking.
Some few more examples which shows the strengthening of houses which can be done easily with diagonal
braces and sheet ply. If you are having wooden ah houses, then you can have used the diagonal
braces which can support this whole ah wall as well as you can use the ah plywoods or
the wooden sheets to protect all this ok. Otherwise if you have just clamped, then here
there are chances of crumpling of this 2 columns here and this 2 members will be will be damaged
and the same is the in case of ah this one ok, but if you have applied the diagonal braces
or the ply, then you can ah safeguard or the structure.
Now, ah with the ah the more ah development in terms of the ah seismic safety ah many
ah countries including India in some places have started using ah the shock absorbers
for the building and this is what we call the base isolation pads which permits a building
to shake less ah than the wall and ah shaking of the ground. So, usually this is been comprised
of lead and this portion is of a rubber base which have been put at the base of the the
building. So, building is going to be resting on this
and whenever there is an big event, this component or this portion or the member will absorb
the ground shaking. So, this is one case which has been shown for the ah the area of ah this
very important building in San Francisco. Now, another issue usually is been faced that
ah as we discussed that different buildings will have ah will sway at different frequency.
So, the shorter building will have different sway at the larger one will have difference
because it will sway larger much more ah area will be covered here. So, if you are having
this two buildings sitting close to one another, then you will have an effect what is we call
the ponding effect and and that will also result into the damage.
So, similar this was from the from 1985 Mexican city earthquake ah where the two building
with the different that is shorter was the rigid and then the and the ah the taller one
was more flexible, they collapsed ok and ah they they have because they sway at different
frequency and they collide during an earthquake. So, this was an example from 1985 Mexican
city and similar ah example, but fortunately it did not damage, but what we see here is
that this is a shorter building this is a taller one and they have almost collided along
this point here and this was from 2015 Gorkh earthquake in Nepal. So, ah I end here with
this lecture and we will continue in the next one.
