noc18-me58-Lec 19-Quasi-Isotropic Laminates

IIT Kanpur July 201
20 followers
Dec 3, 2023
Hello, welcome to Advanced Composites. Today is the start of the fourth week of this course.
And, this week we can we will particularly focus on failure of composites, at the ah
laminar level as well as the at the level of the entire composites track that is the
laminate level. But, before we start these two topics I would
like to come where one more lamination sequence because, in last week we had discovered discussed
several types of lamination sequences which had some special properties . So, we ah had
discussed angle ply laminates, cross ply laminates and so on and so forth. Today we will discuss
one more lamination sequence known as Quasi-Isotropic Laminate .
So, these quasi-isotropic laminates they are such that they are isotropic in the plane
of the laminate. If you go out of the plane they may still be anisotropic , but within
the plane wave behave as isotropic laminates; which means that there A matrix because, A
matrix relates to stress stresses and strains within the plane of the ah plate .
So, their A matrix is very similar to that of isotropic plates. However, these laminates
may or may not have B matrices which are 0 and they may not necessarily have a D matrix
which is similar in nature to that of a isotropic material .
So, that is why we call these types of laminates quasi-isotropic where isotropic in the plane
of the plate, but not necessarily isotropic outside the plane of the plate. Now, if we
look at an isotropic material let us say steel and then we try to develop its A matrix.
Then, for isotropic materials the A matrix ah looks something like this E t over 1 minus
nu square nu E t divided by 1 minus Poisson's ratio square. Third element is 0, this is
also 0, this is 0; this is 0, this is a symmetric matrix . So, nu E t over 1 minus nu square
and this is E t over 1 minus nu square . And finally, the last element is E t divided
by 2 into 1 plus nu E t . So, this is the A matrix for a isotropic plate, it is the
A matrix for an isotropic plate. And, if we look at this A matrix what we find is that
A 1 1 equals A 1 2 this is one equivalence, the other thing we notice A 1 2 equals A 2
1 and that equals nu times A 1 1 ok . So, this should be A 2 2 and the third relation
is that A 1 6 equals A 2 6 equals 0. And finally, we can also see that A 1 1 minus A 1 2 equals
twice of A 6 6 ok . So, these are the characteristics or relations between different alum A matrix
elements for a plate which is made up of purely isotropic material .
So, if we want to have a quasi-isotropic laminate we will it will be here, it will be quasi-isotropic
if these relations are preserved for a quasi-isotropic laminate. Now, typically you can get a quasi-isotropic
plate or a lamination sequence if you follow some rules, when you are arranging the ah
different layers together . So, rules to ensure quasi-isotropy . So, so,
the first thing is that the number of layers should be more than or equal to 3. You cannot
have a quasi-isotropic ah system a laminate, if you have less than 3 layers so, minimum
is 3 ok. The second is that each layer should have same Q matrix, I am not talking about
the Q bar matrix, but Q matrix should be the same which means that the material system
for each layer should be same. The third-one is that each layer should have
same thickness and the fourth-one is orientation of layers should be spaced by should be spaced
by an angle equaling pi over n radiance ok . So, if you have a 3 layer system then they
should be maybe, if the first layer is 0 degree, second layer is 60 degrees, third layer is
120 degree like this. If you have 4 layer system then 0, 45 minus 45 90 or things like
that ok . So, some examples so, for a 3 layer system
we will have 0 and then plus minus 60 because, minus 60 is same as 120 degrees ok. For a
4 layer system so, by the way this does not mean that adjacent layers have to be off by
pi over n ok because, what really matters is thickness times Q bar . So, it does not
matter the location of the layer in the system is not that important. The location of the
layer in the z direction becomes important when we are calculating elements of B matrix
and D matrix, for A matrix it is the thickness which matters ok.
So, for a 4 layer system it could be 0 plus 45 minus 45 and 90. Now, it just turns out
that both these lamination sequences are not symmetric in nature. So, they will have a
B matrix . So, if we want to have a quasi-isotropic plate which is also having 0 B matrix, which
is it does not have a bending this coupling stiffness matrix then in that case we could
have a lamination sequence of this type . So, it is symmetric or another lamination
sequence could be plus minus 45 0 90 symmetric and so on and so forth . So, these are also
quasi-isotropic systems and the first set is also quasi isotropic in nature, but it
just turns out that the first set ah does have a non-zero coupling ah stiffness matrix
. So, what we will do next is we will do an example
and before we start doing the example so, these quasi-isotropic laminates can also be
used to estimate the Young's modulus and G that is the shear modulus of single layer
lamina or layer single layer composites where the fibers are randomly placed.
We can ah do that also and how we do that is less that is that is something we will
learn in this example . So, what is this example all about? So, we say that let us say we have
a 0 plus minus 45 90 laminate ok. Now, and we are making this laminate not necessarily
from continuous fibers for, but from short fibers, we are making it from short fibers
. So, we are making two laminates: one is this plus 0 plus minus 45 90.
And, then we are also making another laminate a different laminate where the fibers are
randomly placed and if they are randomly placed, then its properties in all the directions
they will be the same. But, we do not know what is the value of Young's modulus of this
randomly oriented fiber mat hm . So, we what we will do is we will somehow figure out a
way to calculate that by using the theory whatever, we have learnt till so, far for
0 plus minus 45 90 quasi-isotropic laminate . So, that is what we are going to do .
So, so this 0 plus minus 45 90 this is a laminate and it will and because so, it has 4 layers
0 degree layer, 45 minus 45 and 90 degree layer. And, all these layers are of the same
material and what we do is; the first thing is that we should know what is the value of
E L E T and all this stuff. So, E L either we can measure it or we can calculate it . So,
E L is 16.26 GPa for this laminate, for one of these layers, ah E T is equal to 4.53 GPa,
nu LT equals 0.32 and nu TL, we can actually calculate it from nu LT.
So, nu TL will be nu LT into E T divided by E L hm. So, this is the relation we already
have discussed earlier. So, this works out to be 0.089 and then G LT is 1.45 . So, these
values we can either measure from a single 0 degree oriented layer or if we have the
material properties of fiber and matrix and we can actually calculate these properties
also ok . So, so this is the data . So, from these data we calculate E R .
So, what is E R? It is the Young's modulus of ah layer where all the fibers are randomly
oriented ok. And, because they are randomly oriented so, its material properties in all
the directions is the same. So, we have to calculate E R and then we have to calculate
G Rand Poisson's ratio nu R . So, this is what we are supposed to do . So, here is what
we will do, first we will compute the A matrix of this laminate .
So, A matrix for calculating A matrix we have to first find the Q bar for each of these
layers hm . So, Q based on whatever we have learnt till so, far Q bar for a 0 degree ply
and I am not going to show all the calculations, but it I am just directly going to share the
numbers . So, it is 16.74 1.49 and 0, 1.49 4.66 0 0 0 1.49 .
So, this is Q bar ok then, Q bar for 90 degrees because
there is a 90 degree ply all also. So, it is actually the same thing, but E L this Q
1 1 becomes Q 2 2 and Q 2 2 becomes Q 1 1 ok . So, 4.66 1.49 0 0 1.49 16.74 0 0 and
1.49 and then the next one is Q 45 . So, we develop find Q 40 Q bar matrix for
45 degree layer and this
is equal to 7.59 4.61 3.02 3.02 4.61 7.59 4.61 3.02 and 3.02 ok and the next one is
Q bar matrix for minus 45 degrees . So, we know and we have discussed this that the only
term which is sensitive to the value of sin are Q 1 6 and Q 2 6 because, they are even
functions odd functions of theta . So, for minus 45 degrees these numbers they
just become negative, everything else remains the same . So, I will just put a plus minus
here . So, if you are trying to find out the plus value then take the plus thing and if
for negative 45 degree orientation use the negative 3.02 as the value .
So, using this now, we do we compute A matrix for the quasi-isotropic laminate. We compute
A matrix for quasi-isotropic laminate for this system . So, we know how to calculate
it. So, I am just going to directly share the results, but before we talk about the
A matrix we have to know the thickness of each layer.
So, we assume that thickness of each layer is 1 millimeters or it does not matter we
can even call it t, it does not matter . So, let us assume that it is t if t is so, it
is 9.1425 t. We are assuming that the thickness of each layer is t ah millimeters, this one
is 3.047 t and then this is 0 3.047 t 9.1425 t 0 0 3.047 t ok. Now so, this is the
system for this is the A matrix for this quasi-isotropic laminate 0 minus 45 90 degrees system .
Now, consider another situation where we have a randomly placed fiber ah random. So, so
in this case it will have three important material properties: E R G R and U R. And
because, this is also having isotropic in the plane so, what will the mat ah A matrix
for this randomly oriented thing will be; it will be E R times t divided by 1 minus
mu square right. We are using the same relations for which
we initially showed for an isotropic plate. ah This is nu R E R t by 1 minus nu R square.
How are we getting these relations? We are getting these relation basically from this
equation ok. Because, this is good for isotropic systems.
This is 0 0 nu R E R t by 1 minus nu R square. And, this is E R t by 1 minus nu R t 0 0 and
and this is G or forget it, it is E R t by 2 into 1 plus nu R ok.
So, what I do is next is I compare the numbers and by comparing numbers then I can calculate
the values of E R. So, I can I compare see this number should be equal to this number,
this number should be equal to this number and finally, this third number should be equal
to this guy . So, by making these comparisons so, by making
this comparisons I can say that E R is equal to A 1 1 square minus A 1 2 square divided
by A 1 1 . So, if you do this math you will find that it actually comes out to be E R
and this is works out to be 8.13 GPa ok, then you have GR . So, actually this entire thing
E divided by 2 into 1 plus nu, this is actually same as GR ok .
So, GR is equal to A 6 6 by t right actually, I am sorry this is there is a small error
here I should divide this by t also hm . So, this works out to be this A 6 6 divided by
t, G R into t is same as A 6 6 ok. So, this works out to be 3.05 GPa and nu R is equal
to A 1 2 divided by A 1 1 and that comes out to be 0.33 .
So, you can say that a randomly oriented fiber mat which has the same volume fraction and
the fiber should be of the same length ok, which has the same volume fraction fibers
are of the same length as in the act ah oriented layer and the matrix is same, if everything
else is same then using this approach you can predict that its Young's modulus will
be 8.13 GPa, G R shear modulus will be 3.05 and Poisson's ratio will be 0.33 . So, this
is what I wanted to capture today and starting tomorrow we will start discussing failure
of composites . So, that is all for today and I look forward to seeing you tomorrow.
Thank you.
