noc19-ee65-lec11

IIT Kanpur July 201
20 followers
Dec 3, 2023
[Music]
[Music]
hello and welcome to this lecture on
fundamental of electric drives in the
last lecture we were discussing 1/2
control converter fed DC motor drive
will continue from that now let us look
at the circuit diagram now this is the
circuit diagram of a half controlled
converter we have two ACS n 2 diode and
this is feeding the armature of a DC
machine separately excited DC motor so
the armature consists of the registrants
part the inductance and the back EMF
that is e now as we have seen before
this can operate in two different mode
that is the discontinuous current
operation and continuous current
operation so first of all we will see
the discontinuous current operation that
we are discussing in the last lecture
that we trigger the SCR say for example
t1 at an angle alpha this is the
positive half cycle so we trigger the
SCR t1 and this here is forward biased
because we have the positive or the
anode so this goes into conduction and
the current starts from zero here the
current here starts from zero so and
then this is the equation when this CR
goes into conduction the conduction this
this side is positive and this side is
negative so this SCR is forward biased
and this diode is forward biased so we
have the conduction through one is here
and this basically through the armature
then it returns back through the diode
let us say we call this to be d1 now
when this scr t1 and the diode d1 are
conducting the input supply
is available at the output armature that
is VA so this is the duty interval we
have triggered at an angle alpha and the
equation is VA the armature voltage is
equal to the resistance drop the
inductance drop and the back EMF and
that's equal to supply voltage that is
VM sine Omega T because the input is AC
supply that is VM sine Omega T now this
equation is a first-order differential
equation so we are familiar with this
equation so if we solve this equation we
get the transient part this is the
transient part here this is the steady
state part here and we also have a
transient part the transient part is
this one so this is a very well-known
solution now we have two Jadis the
impedance of of the of the armature
circuit that is the resistance for the
reactants and theta is the impedance
angle or the power factor angle now the
current starts from zero and it reaches
at some value at alpha equal the Omega T
equal to PI the Omega T is in the x axis
so we have the omega t in the x axis
here so at PI this reaches the value
that is IA PI so at Omega T equal to PI
the current is ie PI so if you
substitute this in equation 1 we will
have ie pi is equal to Omega T is PI so
Omega vm by jade sine pi minus theta
minus e by ra and we have e by RA minus
VM by J sine alpha minus theta then
exponential pi minus alpha into cot
theta theta is this tan inverse of Omega
L by RA
now this is and then from PI to this
equation is valid for the duty interval
that is from alpha to PI now at PI the
voltage will try to become negative so
this will be prevented by the diode we
we have the diodes here two diode this
is d2 and this is t2 the ECR p2 and from
the angle PI to beta that will be
freewheeling because we have some
inductive current here and in that the
inductive current has a energy so the
energy will be freewheeling through the
diode d1 and d2
so the voltage VA will be equal to zero
so this voltage is equal to zero and the
current will decrease why will the
current decrease because this current is
is opposed by the back EMF that's equal
to e so the back EMF will be will be
opposing this current so the the current
is being opposed by the back EMF so the
current will be decreasing exponentially
so this is how the current will be
decreasing so that interval is called
the freewheeling interval now in the
freewheeling interval we have a simpler
equation and then if we substitute the
value of this constant a which is
evaluated when we substitute at Omega T
equal to PI I a equal to ie a PI so we
get the final equation of the current
for the freewheeling interval which is
of this nature now at Omega T equal to
beta the current is again equal to zero
at this point the current is equal to
zero at an angle beta so we can
substitute this here and we'll get I
equal to zero so this is equation which
involves sine and exponential so this is
ie PI and I a PI we have already
evaluated the expression of the ia
pi is is given in equation two so we can
substitute the value of I a PI in from
Equation 2 in this equation and this
equation is in transcendental equation
the equation 6 is a transcendental
equation which involves sine functions
and exponential function this is not an
algebraic equation so we don't have any
closed form solution for beta we want to
evaluate at what point the current comes
down to zero so that cannot be evaluated
in a closed form with a closed form
solution so the value of beta has to be
found out alternatively so this equation
six has to be solved iteratively to find
out the value of beta now let us see the
average voltage now what is this average
voltage now we have seen in this voltage
wave form that we have the back EMF e
here the back EMF is e and the voltage
is V ay is armature voltage and the
current is the armature current we would
like to find out what is the average
armature voltage V a now we have to
integrate from alpha to PI and then from
beta to PI plus alpha because the
voltage is zero between pi to beta so
the armature voltage is zero because
there is a freewheeling here this the
freewheeling is taking place here so
between PI to beta the voltage is zero
so we don't have to integrate so
integration is basically from alpha to
PI and then beta 2 pi plus alpha so this
we will see here so the average output
voltage is equal to alpha 2 pi VM sine
Omega TD Omega T and then from beta 2 pi
plus alpha the back EMF E and D Omega T
now let's see what we get here that's
equal to 1 by pi now this is
VM into cos alpha plus one and the
second term will be the back EMF pi plus
alpha minus beta so this is the armature
voltage now we know that in the armature
circuit what we have here is the
resistance inductance and the back EMF
so our a Hale a and E and we have
applied here the armature voltage V a
which is the average value the average
inductance drop is zero so we can write
down here that the voltage armature
voltage is equal to R a ia capital ia
that is the although the instantaneous
voltage current is IA the average value
is capital ia plus e the back EMF is the
drop across the inductor the average
drop across the inductor is 0 because
the inductor is an ideal inductor
doesn't have any resistance so the
average drop across the inductor is 0
now our objective is to draw the speed
torque characteristic so we get the
value of V a from the above equation so
we can substitute that here that is VM
into 1 plus cos alpha by PI plus e into
PI plus alpha minus beta by PI is equal
to R a ia plus e now we we can rearrange
this equation we can we can take this to
the right-hand side or to one side and
and then we can simplify this
so what we
is the following e into pi plus alpha
minus beta by PI minus update plus 1
that's equal to VM 1 plus cos alpha by
PI minus Iara now if we if we simplify
this what we get here is e and then PI
pi will cancel so we get here beta minus
alpha by PI that's equal to VM 1 plus
cos alpha by PI and we know that the
torque equation is K Phi ia or we can
say that the current ia is torque by K
Phi so this we know so we can substitute
the value of ia here so that's equal to
minus RA T by K Phi so the back EMF is K
Phi Omega M that's equal to VM into 1
plus cos alpha by beta minus alpha minus
RT by K Phi into beta minus alpha PI is
in the numerator or we can say that
Omega M is equal to VM into 1 plus cos
Phi by K Phi
beta minus alpha minus ra T PI by K Phi
whole square into beta minus alpha so
this equation represents the torque
speed characteristic of hop control
converter fade separately excited DC
motor now this is for discontinuous
conduction so this is for discontinuous
conduction so when the current is
discontinuous now what happens if the
current is continuous now if the current
is continuous the flow is maintained and
we get a different kind of waveform the
voltage and current waveforms are
different so if we take continuous
current case continuous current
operation
so what we can get here is a following
we have the voltage the rectified the
input voltage and here we are triggering
at an angle alpha this is PI and here we
have pi plus alpha so at this instant
with trigger is here t1 this instant at
PI plus alpha in the negative half cycle
we trigger this here t2 so this is the
origin 0 and we have Omega T in the
x-axis this is 2 pi there could be some
back EMF but usually for continuous
conduction the speed is low and the back
EMF is on the lower side so this is e so
the current waveform is continuous it
means the current starts from some value
here and then this goes like this so
this is the nature of current current
never goes down to zero here so what
about the voltage waveform will be
trigger at an angle alpha the voltage
waveform becomes the input voltage at
alpha we have freewheeling alpha 2 at pi
we have the freewheeling start of the
freewheeling interval pi 2 pi plus alpha
then we have the next SEL is triggered
and the voltage waveform is of this sort
so if you take a steady state nature so
the voltage the voltage waveform is
periodic so this is the armature voltage
and we have this is the armature current
so in this case we have the output in
this case the average output voltage VA
can be evaluated in a straightforward
fashion because we don't have any back
EMF here we don't have any zero current
in
so in that case we can integrate here
just from alpha to PI from alpha here to
PI because from PI plus PI to PI plus
alpha the voltage is zero this voltage
is zero here again from zero to PI also
voltage is zero so we just have to
integrate from alpha to PI so when we
integrate from alpha to PI the input
voltage the input is VM sine Omega T
over this D Omega T so what we get here
is one by PI into 1 plus cos alpha into
V R or we can rewrite as VM into 1 plus
cos alpha by PI so this is the output
average voltage for continuous
conduction and continuous conduction
happens for low value of speed now if we
draw the torque speed characteristic for
continuous conduction we have a simpler
equation here so this is equal to ia RA
plus the back EMF or we can write here
Omega m is equal to VM into 1 plus cos
alpha by PI K Phi minus T ra by K Phi
square so this equation is valid for
continuous conduction continuous
induction now let us compare this to
equation just previously we saw the
equation of speed and torque
relationship for discontinuous current
conduction this is the equation and for
continuous conduction we have
this equation so we can draw the torque
speed characteristic
now one thing we can observe what is the
range of alpha here so the range of
alpha is actually from 0 to 180 degree
this is the range of alpha and for full
range of alpha the voltage is always
positive
this this voltage for continuous
conduction is always positive so it
means in case of a hop control converter
the armature averaged armature voltage
can never become negative so this is a
one quadrant converter this can operate
only in one quadrant because the average
voltage cannot be negative here there is
a freewheeling path so the voltage will
come down to zero now here if we draw
the torque speed characteristic we we
take the help of this continuous
conduction case that is this equation so
this is these are the straight lines for
various values of alpha let us say this
is the first one then we have second one
second value of alpha we have the third
value of alpha and continue like this
so this let us say this is alpha equal
to zero and this is alpha equal to
thirty degree alpha sixty degree alpha
90 degree alpha 120 or and so on and as
we have already seen this is the speed
in the y axis and torque in the x axis
and for a low value of torque the speed
the equation will be governed by some
other equation which is the discourteous
conduction so this this dotted line
represent this continuous conduction
and so on so this is the boundary
between continuous and discontinuous
conduction even for alpha equal to 120
also we have discontinuous conduction so
we'll have some no load speed so this
region is for continuous conduction
and this region is the discourteous
conduction
and for the discontinuous conduction we
have the equation that is this equation
so if I call this equation a let us say
this equation a is for the discontinuous
conduction and equation B is for
continuous conduction so this is
governed by equation B and this are
governed by equation a so now the
Knoller speed for discourteous
conduction will be 4 alpha from 0 to 90
degree this is VM by K Phi V M by K Phi
this this is the no load speed so we can
write here that no load speed for alpha
greater than 0 and less than 90 when the
conduction is discontinuous
is given by Omega M not that's equal to
V M by K F I so when the conduction is a
discontinuous for no load it means when
we are talking about no load condition
torque is zero so how can the torque be
zero the torque can be zero provided the
current is zero because we know that
torque is a function of flux and current
so when we say that torque is zero it
means the current has to be zero because
we have a separately excited DC motor
and when the current is zero it means
the back EMF is a maximum possible value
that is VM so when the back EMF is VM is
equal to VM naturally the no load speed
is equal to VM by K Phi so that is the
the no load speed for alpha between zero
to 90 now if alpha is greater than 90
the no load speed is given by this
equation
no lore speed in this case is given by
VM sine alpha by K Phi because V and
sine alpha will be the maximum value of
voltage that you can have when alpha is
more than 90 so the back EMF should be
equal to the maximum possible armature
voltage that is VM sine alpha to make I
equal to zero so now in this case we
have the motoring so the motoring is a
straightforward case
so for motoring we have this half
controlled bridge where we have 30 stir
and diode and this is
the armature circuit the field is a
partly excited
this is single-phase input here is the
input so this is the motoring case we
have the voltage here that is V a so for
motoring what we have in this case that
VA is positive and the current is
positive and speed is positive now when
we talk about the braking in this case
the braking is not directly possible so
what we have to do here for braking we
have to reverse the back EMF now when we
reverse the back EMF braking will take
place and in that case we have the same
converter circuit half control converter
we cannot achieve regenerative braking
here so in this case the back EMF has
reversed either by reversal of speed or
by reversal of field so if suppose the
speed has reversed initially we have
Omega M Omega M is zero so in this case
what we have here Omega M has reversed
so if Omega him him has reversed the
back EMF will reverse because the field
is separately excited field is constant
here and we have the armature armature
is supplied from AC supply so we have
the voltage VA
in this case now this VA is coming from
the converter so the current is still in
the same direction because we have the
converter circuit the converter can only
allow the current to flow in one
direction so what we have here is VA is
positive the current is positive here
the speed is negative and
and the power of course here is negative
B is negative the power is negative so
this is the the braking in this case but
unfortunately the power in this case
cannot be fed back to the supply the
mechanical power is negative PM is
negative because the torque is positive
but the speed is negative here earlier
we had torque positive and speed
positive but in this case we have torque
positive but speed is negative the
mechanical power is negative in the
earlier case the mechanical power is
positive so this type of braking is
called plugging and this is the reverse
plugging because the speed has reversed
so in case of a hop control converter we
cannot achieve regenerative braking
because the converter cannot refer the
voltage neither the current can be
reversed so the braking energy here when
the motor is being braked electrically
the braking energy is wasted in the
armature resistance so this is the
limitation of hop control converter we
have forward motoring but we can only
have reverse plugging so we conclude
that today's like share will continue in
the next lecture
[Music]
[Music]
