PneumaticComparators: pneumaticsensitivity, overallmagnification To access the translated content: 1. The translated content of this course is available in regional languages. For details please visit https://nptel.ac.in/translation The video course content can be accessed in the form of regional language text transcripts, books which can be accessed under downloads of each course, subtitles in the video and Video Text Track below the video. Your feedback is highly appreciated. Kindly fill this form https://forms.gle/XFZhSnHsCLML2LXA6 2. Regional language subtitles available for this course To watch the subtitles in regional languages: 1. Click on the lecture under Course Details. 2. Play the video. 3. Now click on the Settings icon and a list of features will display 4. From that select the option Subtitles/CC. 5. Now select the Language from the available languages to read the subtitle in the regional language.
[Music]
[Music]
so we will continue with the comparator
so in this lecture we will try to take
up pneumatic comparator so till now what
all have we seen we have seen mechanical
comparator with then we saw electrical
comparator optical comparator optical is
the most accurate or optical comparator
so these are something which we saw and
the last part of the comparator is
pneumatic comparator of course hydraulic
can be used but the only problem is
hydraulic if you pass through an orifice
it is leaking and it will create lot of
problems so pneumatic operator is the
last one which is very important which
is used in almost all industries
industries for the regular application
that means to say at the shop floor
level if you want to measure your
diameter of a hole or a diameter of a
barrel component so then what they do is
they quickly go for a pneumatic type and
the pneumatic type is very easy accurate
and it is also sensitive so pneumatic
comparator pneumatic means air air is
used for measuring the basic principle
involved is that the change that is that
the changes in the calibration
calibrated flow response to the changes
in the part feature for example when
there is a diametrical change then
immediately what happens is there is a
flow which happens this flow is
restricted or it is changed because of
that there is a back pressure that back
pressure is known this is achieved by
using several methods and it is referred
to as pneumatic gauging air gauging or
pneumatic petrology since pneumatic
gauge lends itself to the gauging of
several features at once it
has become an indispensable part of
production inspection in the industries
this is what I was trying to tell
so more than mechanical pneumatic here
pneumatic you don't have moving parts so
a moment the number of parts are reduced
then the repeatability and reliability
of the equipment goes very high that is
why today it is people always move to
pneumatic too people move to electrical
because it is all non-contact and people
look for optical optical today they use
exhaustively laser the assignment what I
gave to you to find out how do they find
the distance from Earth to moon is by
using a laser so optical electrical
pneumatic L becomes a more in usage as
compared to that of mechanical because
of their number of moving parts is less
and they are you very easily adaptable
to the production environment pneumatic
metrology is quite popular because of
several advantages it has absence of
metal to metal contact so there is no
wear and tap high amplification can be
done depending upon your circuit
pneumatic circuit what you develop and
it is low cost reliable absence of metal
to metal contact between the gates and
the component being inspected greatly
increases the accuracy of measurement if
you go back and see in the dial gauge
type we always said that the dial gauge
there is a wear and tear which is
happening at the tip so this wear and
tear leads to an error when you try to
measure it okay and the pneumatic gauges
are best suited for inspecting multiple
dimensions of a single part setting
range from 0.5 millimeter to thousand
millimeter this is on the higher scale
but generally in a shop floor automobile
industry hydraulic industry
infrastructure building so we always go
talk about point 5 accuracy millimeter
accuracy it is also amenable for online
inspection of part onboard a machine
tool or an equipment this also can be
done very easily with the pneumatic type
comparator what happens in a numerical
comparator or pneumatic comparator how
does the circuit look like basically
what happens you try to take air from a
compressor so whenever you try to take
an air through a compressor what you do
is you try to take free air then you try
to compress the air when you try to
compress a free air there is a
possibility that you might have dust
okay you might have some amount of water
vapor and you might have other foreign
particles so all these things from the
compressor first thing it gets into a
filter so this filter tries to filter
all these things to a large extent then
the from the filter whatever you have
filtered there that is here you
basically a filter will be like you can
have a paper filter through which the
air is pressurized to move it has
orifice the dimensions of the orifice
can be changed depending upon your
requirement then this is allowed to go
to a pressure regulator so in this
pressure regulator you try to control
what is the pressure you want to have
such that you have a uniform flow then
what we do is it this after this the the
pneumatic or the air compressed air is
passed through a controlled orifice evo
of a cross-check of an area of C control
orifice C naught of area C then it
passes through a pressure gauge of
indicator here it is a regulator here it
is an indicator look at the difference
here it regulates here it only shows
then afterwards it is just then passed
through here measuring orifice M naught
of diameter D so this is controlled
orifice this is the measuring orifice
once I say measuring orifice through
which the air exits the setup and then
you have a restriction surface whatever
is the restricted surface it can be when
you try to do a hole suppose this is the
gates and then you have hole which is
there and then you will have a component
these are the orifices these are nothing
but the measuring orifice em not okay
and this is the restricted surface so
schematically we have put but in real
time you can have it so if it is a
cylindrical component then it can the
component can rotate or it can be
through here it is a blind one which I
have drawn okay this is the restricted
surface so the distance between the
measuring orifice of the Daiya and the
restriction orifice is called L so the
surface area of imaginary cylinder that
is M is nothing but this and here the
orifice diameter is d and this is the
length so this is the zoom to figure of
it this is the D whatever is given here
so in correctly designed a pneumatic
device the ratio of the orifice area is
so proportioned that within your limited
range of restriction the rate of change
of P is uniform so DP by DL we will try
to maintain it as constant so the
effective area M of the air escaping
from the measuring jet is this I am
nothing but PI into D into L so the
sensitivity of a pneumatic gage can be
brought like this so this is DP by P and
this is M by C so there is a ratio so we
try to put these two in ratios and then
we try to take a linear range whichever
is there and try to operate our device
within that linear range investigations
have shown that when the ratio P by P
and the area ratio M by C are plotted
over a wide range of supply pressures
from 15 to 500 kilo Newton per meter
square the general linear equation may
be written in this form linear equation
this is nothing but basic linear
equation of y equal to MX plus C so what
we are trying to do is we are trying to
take this linear equation bring it here
Y linear because
linear is a place where we can try to
dictate or demand what output we want
we're here K is the intercept of P by P
axis so if you go back P by P axis okay
K and axis and it is found to be one
point one zero go back to the figure one
point one zero and B is the slope which
varies from 0.4 to 0.6 M is the area
which is given by DL and C is the area
of controlled are FS which is M max
minus MN which is half M average so
differentiating P with respect to M what
we get is the sensitivity of the
pneumatic system we get so this is
nothing but this so now what are we
trying to talk about we are trying to
talk about the sensitivity how much a
cure or what is the resolution how do
you improve the resolution is nothing
but this sensitivity so with this we we
will try to take this equation further
however it must be remembered that M is
dependent upon C if you go back to the
previous figure you see that M this is M
naught and this is C naught so M is
depended on C C since if we work with a
range of 0.6 to 0.8 then the average
value of M corresponds to P by P is 0.7
if you go back and look into the figure
P by P 0.6 to 0.8 and this is somewhere
here so we are trying to take this
portion 0.7 P by P is point seven so P
by P is point seven one point one so we
put back into the equation we try to get
the value for C so this is the ratio for
BC then substituting back into the
equation ignoring the negative terms so
DP by DM is nothing but 0.4 times P
divided by M average so this is nothing
but the sensitivity now if we want to
look at the overall magnification the
overall magnification is the rate of
change of output with respect to input
that
magnification the output variable in the
pressure gage or water column reading
today it is only pressure gauge and the
input variable is surface displaced is a
surface this displacement the three
factors combined to produce the overall
magnification are pneumatic sensitivity
indicator sensitivity and measuring head
sensitivity so that is nothing but DP by
DM place one role then DG by DP that is
nothing but the output gage
magnification where G is the gage
reading and P is the pressure and the
measuring head sensitivity that is the
rate of change of M with respect to the
displacement of the restricting surface
DM by DL so this one plus this one plus
this one are the three major factors
when it is combined try to overall
effect the magnification of a pneumatic
device so the overall magnification is
nothing but DG by DL is equal to DP by d
em into DG by DP into DM by DL so where
m is given by this and DM by DL is given
by PI D so L max minus L mean is equal
to half so in the linear scale of our of
the length R provides a reading of P
over the range of 0 to P then DP by D G
is nothing but R by P and this is DG by
DL which is the gauge you have combined
and we have got DG by DL is 0.4 times R
by L average and what is L this is your
L okay this is your L so keep that in
mind
this is URL this is d okay when we said
PI DL this is what is D and L so the in
the linear scale of length R which
provides the reading of P over the range
of 0 to P then DG by DP equal to R by P
so after this magnification this is what
we try to get in this equations so to
recap what all we saw in this but the
a chapter where in which we studied
about comparators we first saw what are
the functional requirement for
comparator then we saw classification of
comparator we saw mechanical type that
is dial gauge Johnson macro micro cutter
then we saw Sigma micro comparator then
we saw a mechanical optical comparator
then LVDT linear variable differential
transformer where in which there was a
primary coil secondary coil and then
inducing then we saw electrical
comparator finally we saw what is
pneumatic comparator so these are all
the different kinds of comparators which
are available in the market which is
used for measurement and again I repeat
comparators are only used for comparing
the bid the standard with respect to the
achieved here we do not talk about the
basic size we talk about the tolerance
alone which is there for example 40 plus
or minus 0.1 so we try to talk about the
range for this and we don't talk or the
basic size measurement we do not do we
just take only the tolerance range and
try to find out whether the component
falls within this tolerance okay so task
two for students so I would like you to
list down list down ten different
components which
components slash feature features which
can be measured only by pneumatic
comparator please write list down the
ten components these assignments are
very useful you don't have to submit it
to me but these assignments are very
useful from the examination point of
view so 10 different comparators or
features you can take a single component
make 10 features in a single component
and say these are the components which
can be made which can be measured only
by pneumatic and not by anything else
the next one is lists down five
different applications five different
applications where LVDT is used we have
talked about measurement you can also
think any or look for any other things
where LVDT is exhaustively used for
application
the last one is profile projector is
used in tool makers in tool rumour or in
tool room application why is the first
question and the next question is draw
different
components for this profile projector
usage for this instrument
Shh okay so these are all just you have
the refer some websites or refer some
books and start writing it down because
there can be an application based
question in your end semester with that
thank you very much
[Music]
[Music]