noc18-ee28 Lecture 47-Optical Modulators-I (Current modulation)

IIT Kanpur July 201
20 followers
1 Video View·Dec 3, 2023
[Music]
hello and welcome to NPTEL MOOC on
fiber-optic communication systems and
techniques in this module we will begin
with part three of the course so far
what we have looked at in part 1 and
part 2 are the kind of building blocks
that are necessary to discuss the issues
in part 3 in part 1 we had a reasonably
detailed look at optical fiber itself we
saw how a pulse can propagate through
the fiber and what does the optical
fiber do to such a pulse that is
propagating of course we have considered
only simple impairments that the optical
fiber would induce on the pulse for
example we have looked at the fact that
pulses when they propagate through the
fiber will be attenuated because of the
fiber attenuation and they will be
either broadened or compressed but most
of the times they will be simply
broadened because the pulses propagate
and they are affected by the dispersion
that is present in the fibers we also
solved the wave equations to understand
what kind of modes are present in a
fiber and different types of fiber for
also considered so we considered single
mode fibers we considered multimode
fibers we considered step index
refractive index profiles and then we
considered greater index profiles and
then we saw that the fundamental mode of
the fibers regardless of what shape that
you have for the refractive index is
that it will be an LP 0 1 mode and most
long-haul optical communication systems
will always use a single mode optical
fiber because those are the fibers that
eliminate intermodal dispersion have low
loss and also they are less susceptible
to effects of dispersion so this is what
we have seen in part 1 and in part 2 we
saw the other part of the optical fiber
communication system that is you have a
source in the form of a semiconductor
laser diode and with some modifications
or in fact which much simpler structure
you can also have
light-emitting diode we did not discuss
much about that but light emitting
diodes work on the basis of spontaneous
emission
while the semiconductor laser diodes
work on the basis of stimulated emission
we saw the structures how these double
heterostructure lasers and quantum well
lasers are actually used to make very
good lasers and basically laser is an
oscillator
okay so just as you have an RF
oscillator or a crystal oscillator the
purpose of a laser diode is to actually
generate as much as possible a pure tone
signal of certain frequency okay we will
of course see that not every laser and
in fact we cannot find any idea lasers
because all practical lasers will have a
certain amount of line width and this
non zero line width will contribute to
the face noise that is induced by the
laser okay of course the amplitude one
would expect it to be constant but this
amplitude would also not be constant or
we talk about the power power will not
be constant there will be random
fluctuations of the power and this power
fluctuations is also something that one
needs to address if you want to make use
of these semiconductor laser diodes as
sources for optical fiber communication
system we also saw that it's not only
necessary to convert you know
information which is usually in the form
of an electrical format into an optical
format we haven't seen the devices yet
that they can do but we are going to
discuss those devices in this module but
we do know that such devices have to
exist those that convert the information
or data that is in the electrical format
into the optical format laser must be
involved a device called modulator must
be involved and after modulation of the
laser light or the light from the laser
diode you will have information
propagating in the optical domain where
it can be coupled to the fiber why are
some other WDM couplers we saw that not
only one particular laser diode or one
particular channel can be propagated in
a fiber simultaneously many channels can
propagate and this necessitates the use
of multiplexers demultiplexers optical
filters so on and so forth and
to over or to compensate the losses that
the pulses will experience as they
propagate through the fiber you will
have to place on pickle amplifiers and
we saw that there are two kinds of
optical amplifiers or BM doped fiber
amplifier and semiconductor optical
amplifier although for all long-haul
optical communication systems it is the
erbium doped fiber amplifier that is
used and these amplifiers have to be
kept at every so and so distance and
this distance between two amplifiers is
called as the span of the optical link
and the span is usually about 100
kilometers 8200 kilometer so we have
seen this in part 2 of course when the
pulses reach the end of the fiber they
have to be converted back into the
electrical domain that is information
which is in the form of modulated light
will have to be converted back to the
electrical domain and we know that there
are devices called photo detectors which
have this job of converting which which
perform this job of converting
information in the light or in the
optical domain onto the electrical
domain of course we have seen that all
this infrastructure is necessary except
for the modulator which we are going to
talk about and in part 3 of this course
beginning today we will actually put
these devices into use in the sense that
we are going to consider how exactly can
one start implementing enough optical
fiber communication system and when one
implements an optical fiber
communication system what are the
impairment that are going to affect the
signals that are propagating and how can
one remove or mitigate these impairments
because if you do not mitigate the
impairments that happen to the optical
signals propagating through this optical
fiber communication system then what you
will have is a mismatch between what you
receive and what you have transmitted in
the case of an analog signal this
mismatch will be in the form of a
distortion and noise added to the
waveform and you normally quantify this
mismatch by the signal-to-noise ratio
you would say that while at the
transmitter the signal-to-noise ratio
was so and so DB whereas at the receiver
if you do not correct for the impe
if you do not mitigate the impairments
the signal-to-noise ratio would have
decreased considerably and perhaps
render the entire communication system
unusable okay on the other hand in the
digital modulation schemes you will be
transmitting usually in the form of
binary signals that is you will be
transmitting bits of 1 and 0 or some
sequence which represents the
information that is given to be
transmitted and the mismatch will be
occasional errors that the receiver
would make in deciding between a 0 and a
1 so if you compare to the total bits
that are transmitted and look at how
many bits are at the receiver are in
error you will come up with what is
called as a bit error rate that is you
assume that these errors are going to be
there on an average but I mean you
normalize it with respect to the
transmission rate and then you say that
this is the bit error rate of the system
and one of the important things that you
will have to take care when you design
communication systems is to keep this
bit error rate as small as possible
about 30 years ago or maybe 25 years ago
many people used analog communication we
know what are the analog communication
types we have learned analog I mean
amplitude modulation phase modulation
and frequency modulation but in today's
communication technology analog
communication especially in the long
haul optical fiber communication simply
does not exist
everything has become digital modulation
because of the various you know
advantages that are offered by the
digital communication system something
that we don't want to go into the
details here but suffice to say that
most of our communication systems today
especially the long-haul optical
communications is in the form of digital
communication and therefore this part 3
will focus mainly on digital
communication occasionally we will talk
about analog modulation or analog
modulation techniques as well but most
of our focus will be on the digital
communication well we will also not
consider the optical networks in the
sense that our consideration in part 3
will simply be from point-to-point
optical communication link so you
have a transmitter you have a fiber and
then you have a receiver okay we do not
consider the cases where you have
multiple transmitters multiple receivers
and multiple optical links
interconnected to form a network that is
something that can be done in a
different course if they understand how
to make good links then we will be
taking one step to make good optical
networks as well so that is what our
focus will be point-to-point links
point-to-point
optical communication systems okay we
talked about lot of devices in the
previous modules those WDM components
which kind of help us in realizing the
full optical fiber communication system
but we left out one very important
component called the modulator of course
that is what we are going to cover in
this model so let us look at what this
modulator is and how do we implement
this modulator we know that if the data
needs to be transmitted on the fiber the
data which is usually in the form of a
current or a voltage or we say that the
data is in the form of an electrical
signal okay has to be converted into the
optical format okay so has to be
converted into the optical format and
this conversion can be done or
conversion has to be done by utilizing a
light source because light source is the
one that would actually generate light
okay so you have a light source of
course in the case of fiber optic
communication system we know that this
light source is going to be a laser
right so this laser would generate light
at a given frequency or at a given
wavelength dodol assume for simplicity
that we are dealing with the wave I mean
frequency over here okay and once the
light comes out of the laser diode
semiconductor laser diode one of its
properties will be used to modulate the
data onto the optical carrier so I
cannot just take the data in the
electrical format and put it on to the
optical fiber I have to modulate this
information or you have to change the
optical signal in accordance with this
electrical signal so what you actually
have
to do is to perform the process of
modulation wherein the carrier
properties and what are the carrier
properties the carrier properties will
be amplitude frequency phase and in the
case of optical fiber communication you
also have an extended degree of freedom
contest polarization we have seen that
LP 0 1 mod can actually come in two
different varieties right so this is
also LP 0 1 more this is also LP 0 1
mode 1 is an X polarized wave and the
other one is a Y polarized mode and
information on each of these modes can
be independently modulated by changing
the amplitude frequency or phase okay
if this change is usually in the form of
a continuous change then we call this as
a continuous wave modulation or analog
modulation but in the case of digital
modulation things can actually be
discrete okay
we will not look at any modulation
technique that would involve frequencies
no we are not going to modulate
frequencies in this course we are only
going to modulate amplitude and phase of
course frequency modulation is a very
important technique but not quite
popular in the optical fiber
communication systems at least not
something that we are going to discuss
it in this course okay so to sum up you
need to have data in the electrical
format and then convert the data in the
electrical format into the optical
format or into optical domain now how do
we go about doing that we know that
laser source is essentially a forward
biased semiconductor Junction right so
it is a PN Junction which will be
producing light send in some amount of
current which would be the forward
current of a forward biased PN Junction
which is acting like a laser we know
that when we forward bias the junction
you are going to move lot of electrons
from the valence band into the
conduction band and because you have
used this hetero structure lasers you
would confine these carriers in their
appropriate bands whether they are in
the conduction band or in the valence
band and just a small amount of forward
bias current would then induce that
these carriers would recombine and then
give off radiation which when you
enclose
in the form of a mirror would form a
self-sustaining emission of light called
as a laser and the light that comes out
of a laser usually in the spectral
domain ideally one would expect it to be
just a pure tone you know of the
frequency Omega not having some
amplitude whatever the amplitude and a
face which is kind of fixed with this
one so if you want to write down an
equation you would probably write an
equation like this eight cos Omega 0 T
plus theta where if the amplitude which
is well-defined
no noise on that and frequency of Omega
0 which is again well-defined and theta
is a phase constant arbitrary phase
constant but it is also time independent
phase okay this is what one would expect
unfortunately what you get is this kind
of a laser output okay so if I want to
express that one I should actually write
down the electric field that comes out
of the laser in this manner so let's say
this is e s of T it could be coming out
with up certain polarization so I am
going to write down the polarization as
X here but please remember it can be any
polarization I have just indicated that
with X and then there is a steady state
power that the laser would put out but
then this power would also be or this
power would actually be subjected to
some kind of a fluctuation which are
denoted by Delta a and this Delta a
would correspond to the amplitude
fluctuations but in reality it is the
fluctuations of the power so maybe
instead of writing this in this manner
by separating out the amplitude I can
include that in the power itself by
writing this as PS plus Delta PS where
Delta PS is called as the relative
intensity noise it is random and then it
has certain characteristics or certain
distributions that we don't really need
to go into at this point usually these
lasers are operated with PS much larger
than Delta PS and where is the source of
this Delta PS well you guessed it the
source for Delta PS is always the
amplified spontaneous emission noise or
rather the spontaneous emission in the
laser so spontaneous emission you
gives us both change in the individuals
both fluctuations in the amplitude as
well as in the face so how does it into
the change in the face well this is what
you're going to get you will get in the
complex form you have E power J Omega 0
T plus theta n of T where theta n of T
corresponds to the face noise which
again has its origins in the spontaneous
emission okay in continously andum or
incoherent phases to be applied on to
the well-defined signal and this is what
your actual output would look like so
you have relative intensity noise which
affects the intensity or the amplitude
and causes fluctuations and then you
have a face noise which affects the face
of the or pretend as you have guessed by
now if you have not already guessed
phase noise will be very very important
when you consider systems in which
information is modulated in the form of
a phase right so when face is modulated
unwanted phase noise would actually
cause errors so this is what your laser
would produce now there is one straight
forward way of modulating the laser
output and that would be to modulate the
current source itself okay so I can put
the current source to generate some
constant value which I will call as say
I EV 0 and I f0 would be the bias
current that is necessary to sustain the
lasing action of the semiconductor laser
diode and any data that I want to
transmit I can actually put that data as
or superimpose that current onto the
forward bias current so if you look at
how the current forward current versus
the light output which is usually
denoted by L and L stands for luminosity
but in our case we can equally think of
this as the power that is coming out
from the laser diode you would see that
this actually follows more or less this
characteristic as the forward bias
increases the power increases there is a
certain threshold value that is
necessary for the laser to begin acting
like a laser itself below that the
the boundless and just about @i f pH
which is a threshold current then the
laser will you know generate most of its
light in the form of spontaneous
emission and that is precisely the area
where LEDs can be designed but if you
bias the laser with a current which is
greater than IFD H that is a threshold
current then it starts emitting light
and if you increase the forward bias
current then the power increases rapidly
usually you have a sort of current
limiting mechanism in your circuit in
the form of a laser driver okay but
nevertheless your laser driver will
usually operate at a certain operating
current
so I F 0 would be the operating current
okay now if you want to modulate data
which I will assume that the data would
look like this in the form of a simple
sinusoidal signal that when you have
light which is in this modulated or this
is a modulating signal or the data
signal out here then what it means is
that when the data is passing through 0
the current through the device is AF 0
and when the current starts to increase
the output power also starts to increase
and then decrease around this current or
the operating current p0 so with a mean
value of p0 you can actually around that
value of p0 or around the value of AF 0
if you happen to put your data current
Delta ID then it is possible for you to
actually modulate the laser output and
then almost faithfully reproduce
whatever the information that you have
by modulating the intensity or the power
of the laser right so this is very
important what you are doing is to
modulate the intensity what is happening
to the face lot of things can be
happening to the face but I do not want
to look at face because my information
is not you know in the form of a face
but it is only in the form of intensity
admittedly this type of a modulation is
not very spectrally efficient will be
usually limited by the speed at which I
can modulate the laser current because
when I modulate the laser current
carriers have to recombine and then they
have to you know again be you know
pushed into the Bands appropriate bands
and confine
and then recombined these processor all
not instantaneous there is some delay in
moving the electrons from the valence
band to the conduction band and then
when the laser or the when the carriers
decide to recombine to generate light
so all those delays have to be
considered and those delays also are
part of or the you know the factors that
limit the rate at which I can modulate
the intensity of the light I can also
modulate the phase but usually we don't
really do that phase modulation onto the
laser current what I just described is
analog modulation because the output is
changing almost in the same manner as
the input okay but please remember that
the peak change or the peak change in
the power must be so that the total
power Delta P maximum value plus the
operating power P zero must be less than
whatever the safe limit of operation of
a laser okay so that really means that
Delta ID magnitude is usually very small
compared to one so this was analog
modulation I can explain the same idea
to digital modulation as well you know
instead of modulating this type of a
waveform I can now operate the laser in
a different condition or different
operating region so I will operate the
laser at this point okay and then moves
a digital signal like this right
so I will apply a current which is in
the form of a step or a pulse and the
effect of this current pulse Delta ID is
that I am now moving the laser from
below the laser threshold that is when
Delta ID is zero you can see that in
this region the output corresponding
output will be zero because you don't
have light lazing out and then there
will be very very small amount of light
power that may come out okay because in
most of the cases there will be slight
amount of power that would be coming out
but that is very small but when Delta ID
is made large every when the pulse
occurs then it would provide sufficient
forward biasing so that the light output
or the laser
then generate light output in accordance
or into the duration over which this is
turned on so this is the digital
modulation and as I told you this
digital modulation format is widely used
in fact it is widely used up to 10 Gbps
standards in about 15 years ago this was
the only format that was widely
prevalent because for that time the
bandwidth requirement was alright it was
not very high and these data rates were
sufficient for those data rates as such
but the most important point is what you
have done is to turn the laser on and
off accordance with the pulse which is
on and off so when the pulse current
pulses on the late output is also on so
effectively what you have done is to
keep a shutter so you this shutter will
open when the current pulse comes in and
this shutter will close when the current
pulse will be turned off ok and
therefore this type of a modulation is
called as on-off keying and how do I
receive this on/off keying output after
propagation the optical pulses would
mostly look like this of course they
will also be noise but I am NOT
indicating the noise here and what you
have to do is to put a threshold and
then compare the current or the current
that you would obtain so this is the
optical signal of course you have to put
this one through a photodiode so light
is incident on this photodiode and then
the photodiode will generate appropriate
current and this is the current pulse
waveform and then you put a certain
threshold value of the current which
will then if the sample output that you
get will be above the threshold you will
have obtained bit 1 if it is below the
threshold you would have received bit 0
occasionally when there is noise you
would actually make an error and it can
be shown that there will be significant
noise so this won't be exactly like a
square wave it will be very noisy like
this but when you keep a threshold and
then your sampling got an unfortunate
time then you may declare a bit as one
or a bit as zero instead of a bit as a
one ok and thereby making a error of one
kind ok this is an error where you have
transmitted one but you decoded the
received symbol as zero ok you will also
make an error
when you make or when you send
transmission a zero but you will receive
this as receiver as one but this usually
does not happen for a photo detector
that is operating in the so called short
noise limit which we have already
discussed a little bit short noise and
thermal noise because short noise
depends on the optical power it will be
usually quite noisy for bit one and
usually that not much noisy except for
the thermal noise in bit zero
transmission so this is the older
digital modulation technique and this
type of a modulation is called as direct
modulation because no other device was
externally used to model it but in
practice you will have to use an
external modulator because as the data
rate increases the direct modulation of
the laser cannot happen because the
laser has all those time delays that I
just spoke about you know in the form of
carriers being recombined carriers being
moved from one band to another brand and
collection of those carriers light and
all those things so the rate at which
you modulate will not be possible by
more than 10 gigabits per second and
moreover you normally when you modulate
this you know even in the on-off keying
you will introduce sufficient chirp and
remember what is chirp chirp is the
unwanted phase fluctuation not that you
care about that phase but what this
unwanted phase fluctuations will do is
to kind of broaden the spectrum of your
data so because phase fluctuations in
time turn out to be frequency
fluctuations in time as well because D
Phi by DT where Phi is the phase is
directly proportional to the
instantaneous frequency so as the data
rate increases beyond 10 Gbps and you
use only laser current to modulate that
is a direct modulation then in addition
to the spectrum that you get the
spectrum will become chirped and
chirping will cause the spectrum to
broaden and this broadened chirp will be
so much that it may actually start
spilling over to the other channels as
well so this is not clearly an efficient
usage of the spectrum and therefore you
don't see any type of modulation
beyond simple on asking for data rates
that is less than 10 gigabits per second
in the direct modulation scheme so then
what do we do we actually have an option
of what is called as external modulator
so in an external modulator I have a
laser diode okay I have a laser diode
and then this laser diode will be used
as a simple oscillator okay the laser
diode will produce light and then I take
that light which can be to a good degree
approximated as a cos Omega 0 T plus
theta or I can write down in the more
common format of root PS e to the power
J Omega 0 T I have neglected this theta
I'm assuming ideal light coming out from
the laser diode but then I can put an
external device and then drive the data
so whatever data that I want to transmit
will still be in the form of an
electrical current or a voltage but this
electrical current or a voltage will go
to an external modulator which will then
depending on the type of the external
modulator will generate on/off keying it
will generate the most general format of
modulation called as quadrature
amplitude modulation and it can also do
what is called as PS K which is phase
shift keying please note that we are
dealing almost exclusively with digital
modulation formats only so how exactly
do we do this and when you look at
direct modulation the simplest variable
to control was the intensity of the
light or intensity of the laser is it
the same with external modulator which
is the simplest variable to contour
which is a simplest modulator structure
then use an external modulator is what
we are going to talk about in the next
module thank you very much
[Music]
[Music]
