noc18-mm20 Lecture 04-Effects of Temperature & Pressure on Single Components System

IIT Kanpur July 201
20 followers
Dec 2, 2023
So, welcome again in this lecture number 4 and here we will continue talking about the
previous lecture. In the previous lecture, we looked at the variation of various, we
looked at the definition of thermodynamic properties, what intensive extensive properties
are and how do thermodynamic properties vary as a function of temperature. For example,
we looked at the variation of specific heat as a function of temperature, which typically
increases as the temperature goes up. Then we looked at the variation of enthalpy as
a function of temperature, enthalpy being dependent upon the specific heat, it also
increases as a function of temperature. And then we looked at entropy, entropy generally
increases with temperature. However, the overall term G, G is equal to H minus T s and so one
increases and this term becoming, so this increases with temperature and this decreases
with because of negative sign due to minus T s term. As a consequence of this, the free
energy, if you plot free energy as a function of temperature, the free energy tends to decrease
as a function of temperature. So, it is the relative change of free energy of various
phases with temperature, that determines which phase will be stable and which phase
will not be stable at a given temperature. So, this is what we did. So, we were, we looked
at for example, this if I, if I change the slide, we looked at the example of liquid
to solid. So, what we saw was that transformation is happening from liquid to solid as you change
the temperature, as you increase the temperature. And enthalpy of both the phases increases
as a function of temperature. And if you, so this is for example, the orange one is
the enthalpy of liquid, the magenta one is enthalpy of solid. If you look at the corresponding
changes in the free energy, the blue one is the curve representing free energy of liquid
and the dark blue one is the free energy of solid. You can see that below a certain temperature
T m, the free energy of solid phase is smaller than free energy of liquid. As a result, solid
is more stable phase, whereas at higher temperatures, G L is smaller than, is lower than G S. As
a, as a consequence, liquid phase is stable at higher temperatures. And if you see the
corresponding changes in the enthalpy, enthalpy shows a sudden jump at this temperature T
m, which suggest that the heat is added in the form of latent heat of melting. However,
there is no temperature change. And basically at this point, if you calculate a specific
heat, specific heat is del H by del T and specific heat would be infinity. So, basically
addition of extra heat does not, does not lead to any change in the temperature.
And if you look at the T S term, the T S term is minus T S. So, T S term is minus.
And as you increase the temperature, the T S term for, for liquid drops much faster as
compared to solid, because liquid will have higher entropy as compared to solid. So, that
is why you see that the free energy for, for liquids, liquid phase, which is the light
blue curve drops much more faster as compared to the free energy of the solid.
And this tells me that, basically what, what I, what I was able to tell you is that, if
I summarize at high temperature G L is lower than G S, making liquid stable. Whereas, at
low temperature G L was greater than G S, which means solid was stable. So, this was
the take home message for, for free energy variation as a function of stability. If you,
if you look at the material systems in single component, then the most common example is
of iron, pure iron. So, pure iron is at, at low temperature, pure iron is B C C structured,
we call it alpha iron, let us say lower temperature. At higher temperature, so lower temperature
would be T less than 910 degree centigrade. And this would be T greater than 910 degree
centigrade, it becomes F C C structured gamma iron.
Now, this basically tells that, if you compare for example, the free energy and enthalpy
now here. So, the free energy, if I plot the enthalpy first, overall change in the enthalpy.
So, this goes through 0 at 298 Kelvin. And then at certain point, there will be change
in, there will be minor change in enthalpy, before it increases further, because you know
this is a solid to solid transformation, both of them are solid. So, this is also solid
and this is also solid. And at this temperature, correspondingly you will have a transition.
So, your free energy of, if I plot the free energy. So, free energy up to this point,
it will be corresponding to. So, at up to this point, it will correspond to alpha phase.
And then beyond this point, it will be, it will suddenly change the shape at this point.
So, this will be G alpha and this will be G gamma. If you wanted to plot the individual
plots, the gamma will continue to be like that and may be alpha will continue to be
like that and gamma will somewhere like. So, these would be the individual plots, let me
put the blue color here. So, this is how they would have been, but if you just want to plot
a single, if you just want to plot a single line, single line will tell you, that initially
the color, initially it would be for alpha and then it will be for gamma. So, in this
phase at 910 degree centigrade, this would be gamma stable and this point it would be
alpha stable. However, unlike solid to liquid transformation,
this delta H will be small, it will not be very large, because all you have is, you have
a solid to solid transformation from B C C to F C C phase. As a result, the change
in enthalpy is not very high, because the internal energy is, as far as internal energy
is concerned, both of these are solid phases. So, there will not be huge change in the internal
energy as far as delta H is concerned. So, this is how the curve is going to look like
for something like iron.
Now, let us look at another effect of another thermodynamic parameter called as pressure.
So, this is, what we want to here is, basically equilibrium as a function of pressure and
its effect on, so and its effect on phase, presence of different phases. So, let us make
a plot of, what we call as, we make a plot of, plot of iron. So, iron is a very nice
system to study this. So, this is temperature axis, this is pressure axis, let us say pressure
is in kilo bar, temperature is in degree centigrade. So, let us make 400, 800, 1200, 1600. This
is 400, this is 800, this is 1200, and this is 1600, and the line is something like that.
Alright. So, this would be nearly 125, should be about 150, about 100. So, it should be
25, 50, 75, 100, 125, 150, they are not very equal. Draw these two little differently,
50 and 75. Now, they are more equally distributed. So, what you have here is, on the y axis we
have temperature, on the x axis we have pressure. Temperature is plotted up to about 1600 degree
centigrade or even higher, and pressure is plotted again up to 150 kilo bar or so. And
at high temperatures, the iron is stable in the form of liquid phase. At, in this regime,
this regime is basically delta iron, within this regime we have gamma iron, which is FCC
structured, delta is again BCC, and then we have alpha Fe at this lower temperature, BCC,
and then we have epsilon Fe, which is HCP. So, this is the pressure temperature phase
diagram of iron, single component pure iron. What we see is that, at lower pressures, so
what we have here is, at lower pressure, the iron transforms to, alpha iron transforms
to gamma iron, alpha is BCC structured, gamma is FCC structured at 910 Kelvin, before it
transforms, and then subsequently gamma iron transforms to delta iron, which transforms
to liquid phase at high temperature, 1500 and something is the melting point of iron.
What you see here interestingly is that, as you change the pressure beyond atmospheric
pressure, the phase boundaries, the transition temperatures change. So, this is for example,
the temperature corresponding to T gamma L, this is T alpha gamma, these are called
as phase boundaries okay, this is T alpha epsilon and this is T epsilon gamma. So, there
are various phase boundaries here, we look at the cases of for example, T alpha gamma
and T gamma liquid. We see that, T alpha gamma decreases as the
pressure increases okay, whereas T alpha liquid increases as the pressure increases. So, you
see the difference, for the transition from, for phase transition from alpha to gamma phase,
both are solid phases okay, from for phase transition from alpha to gamma phase, as increase
the pressure, the phase transition temperature decreases. On the other hand, for transition
from gamma solid phase to liquid phase, the phase transition temperature goes up, as the
pressure increases and we will see, why this happens in the next few minutes.
Now, the observations are, as pressure increases, T alpha to gamma decreases, T gamma liquid
increases and of course, at very high pressure, what we obtain is a different phase, which
is epsilon F e. So, at from the free energy relations, at constant temperature, you can
obtain this from the free energy expression that we wrote. So, we wrote d G is equal to
d H minus T d S minus S d T and if you expand this further, at constant temperature, you
will make certain terms equal to 0, at constant temperature what happens is that, del G by
del P at constant temperature, this will be equal to V.
So, basically as pressure increases, G also increases and the slope of del G by del P
is the volume. So, this suggests that, what it says that, what it says, you can see from
here is, as the pressure changes, del G by del P is equal to volume. So, as the pressure
changes, the G will change, you have two phases, phase 1 and phase 2, V is nothing but, the
molar volume. So, we can say this is the molar. Now, suppose you have two phases and for though
both of these phases, V 1 is not equal to V 2, the free energy changes as a function
of pressure, but V 1 is not equal to V 2. So, what will happen, if V 1 is not equal
to V 2, which means the free energy change for both phases is not similar, which means
delta G 1 is not equal to delta G 2, which means if these phases had to exist in equilibrium,
for phases to coexist in equilibrium delta, the free energy changes for both of these
must be equal, but they are not equal. So, in order to make them equal, what will
now happen is that, so to make equilibrium work, you have to, temperature has to be changed.
So, this is a problem in specially, when the phase volumes are very different. So, molar
volume of two phases V 1 and V 2, they are different to each other, as a result when
you change the free energy as a function of pressure, the changes in the free energy are
not similar. And if the changes in the free energy are not similar, which means one is,
one phase is going to be stabler than another phase, that will create a problem at equilibrium,
because at equilibrium both, if these phases, if these two phases have to coexist with each
other at a certain temperature and pressure, at a certain pressure, then temperature also
has to be changed. So, that is why you see in this plot, at these
lines, at these lines the phase boundaries both the phases coexist. So, at this line
both the phases coexist, at this line both the phases coexist. And this temperature is
decreasing, this temperature increasing, because the molar volumes of two phases are different.
As a result to maintain the equilibrium, because remember at this point, the free energy of
both the phases are equal. So, to, so as you change the pressure, the molar volumes have
changed, as a result the free energies of both phases are not same. So, to maintain
the similarity of free energy changes, you need to change the temperature. And in this
case the temperature increases, at this pressure, in this case for example, the temperature
decreases as you increase the pressure by the same amount.
So, let us see this in more quantitative framework. So, basically we are going to define this
now in the, what we call as quantitative framework. So, you consider phase, let us say 1 and 2,
in equilibrium. So, and assume both have 1 mole of each all right. So, the incremental
change in the free energy, so I can write for phase 1, dG 1 is equal to V m 1 dT dP
minus S 1 dT. For phase 2, dG 2 is equal to V m 2 dP minus S 2 dT, where V m is the,
we say V m is the molar volume ok. So, V m is basically the molar volume.
So, now assume if 1 and 2 are in equilibrium, which means G 1 is equal to G 2 and if G 1
is equal to d 2, then dG 1 is equal to dG 2 as well. If that is the case, then I just
equate the 2 equations. So, V m dP minus S 1 dT is equal to V m 2 dP minus S 2 dT.
And if you rearrange the terms, what you will get is dP by dT at equilibrium. So, this is
at equilibrium ok. So, at equilibrium it will be S 1 minus S 2 divided by V m 1 minus
V m or you can say this is equal to delta S divided by delta V, the change in the entropy
of 2 phases and the change in the molar volume of 2 phases.
So, basically what we see in this equation is, you can determine the change in temperature
if the pressure is changed and the molar volume change is not equal to 0. Now, how to now
calculate delta S? So, delta S can be calculated very simply, we know that for both phases
G 1 is equal to H 1 minus T S 1, G 2 is equal to H 2 minus T S 2. So, you can write delta
G to be equal to G 2 minus G 2 minus G 1 and which is equal to delta H minus T delta
S. And we know that at equilibrium delta G is equal to 0 as a result delta H is equal
to T delta S or delta S is nothing but delta H divided by T, where delta H is the change
in enthalpy, the enthalpy of transformation. And so this will make my equation read as
d P by d T at equilibrium is equal to delta H divided by T, you can say T c the transformation
temperature into delta V. So, this is important expression which allows you to calculate the
change in the temperature, when the pressure of a system is varied. And if you have delta
V which is not 0, when the two phases of different molar volume then to maintain the equilibrium,
what is the change in temperature that is required. This equation is called as Clausius
Clapeyron equation, it is a very important equation as far as phase transitions are concerned.
So, you can see that if a molar volume change is negative and if pressure is d P is positive
then d T will be negative. If you delta V is positive, if you delta V, if delta V is
0 then obviously d T will be 0 as well, but if delta V is positive then P is positive
then d T will also be positive. So, you can see the temperature, the temperature to maintain
the equilibrium will increase or decrease depending upon the sign of delta V as if d
P is positive. So, we will see the ramifications of this equation on the iron phase diagram
as we saw earlier on the two phase boundaries in the next class.
So, in summary I would just say in this class, in this lecture what we have learnt is the
effect of thermodynamic variables on changes in the free energy for as far as single as
far as phase transformation in single component systems is concerned. So, at a certain transition
temperature the transformation happens as a function of temperature below that temperature
free energy of one phase is lower and above that temperature free energy of another phase
is lower making the two phases stable in different regimes.
And then we looked at the effect of pressure which is related to which in most cases related
to change in the molar volume which has its own repercussion on the change in the temperature
as well transition temperature as well. So, we look at that in more detail in the next
class.
Thank you.
