Lecture 11

IIT Kanpur July 201
20 followers
6 Video Views·Dec 1, 2023
Welcome to the next lecture in the course Metal Additive Manufacturing on Electron Beam
Processing.
In the last lecture, we understood little bit of fundamentals about laser, laser why
in laser they talk about 2 level, 3 level, 4 level.
Second thing is we were trying to look into m square value, we were also trying to look
at theta the beam divergence.
So these things are very much important because when we have to produce a high quality output
these fundamentals are very much required.
Because today world is moving very fast in developing different metal alloy powders.
So in that case process optimization is a very big challenge.
We will of course see a lecture exclusively on various process parameters using laser.
In this lecture, we will try to cover about electron beam process, laser beam process
and electron beam process are the most prominent ones used in powder bed fusion technique.
The content of this lecture is going to be basics of electron beam.
When we discussed about laser, laser the basic small element is called as photons.
Photons are nothing but a packet of energy.
When we talk about electron beam, the basic small unit is electrons.
A series of photons focused in a small point and you try to selectively sinter or melt
was done in laser.
In electron beam, you replace that photon into electron.
So here there will be a beam of electrons trying to hit at a powder where you can do
electron beam sintering or you do electron beam melting.
Predominantly here we use only for electron beam melting.
We will see the basics of electron beam.
Then we will see how is this electron beam powder bed fusion system exist.
Then the last one is going to be electron how is it generated in mechanisms, we will
see electron beam mechanisms.
Like laser, electron beam is also a thermal source wherein which this thermal source is
used for melting and sintering to produce output doing it layer by layer approach.
Electron beam a collimated, there we saw coherent.
So here we see collimated stream of free electrons are focused on a small spot for doing heating
operation or doing welding operation.
The electron beam are nowadays used for microscopy and nanoscopy.
It is used for machining, it is used for welding and to a large extent, it is also
used for spectroscopic techniques today.
The spectroscopic techniques are today used for online monitoring during the process of
AM, additive manufacturing.
The electron beam power is enough to cut, machine and weld.
Focus beam if it is very small, very high energy density comes, it can be used for cutting,
machining and welding.
Today when we talk about processing micro and nanoscopy, you can think of using TESEM.
You can also think of using TEM, Scanning Electron Microscopy or Transmission Electron
Microscopy falls in these two what I was talking about.
Let us try to compare laser and electron beam.
Electron beam are very coherent and have low numerical intensity source of very high kinetic
energy, potential energy, kinetic energy.
So, electron beam has low numerical intensity source of high kinetic energy.
High kinetic energy means lot of energy is there when it tries to hit at a powder.
So, when it hits a powder, immediately the temperature of the powder goes high and it
starts melting.
So, while laser has high numerical intensity source, but low energy photon.
So, this is why electron beam is more preferred as compared to that of laser, but laser has
its own advantage which you will be able to appreciate while going through this lecture.
Both energy sources are collimated and can be concentrated to a tiny region while achieving
great thermal intensities.
These consideration make fine feature items manufacturable.
When the laser beam or the electron beam hits at a small spot, this is either laser beam
or electron beam.
When it tries to hit at a small spot, it can create fine features while doing AM.
The difference between these energy sources is heat transfer to the powder bed.
The laser heat by absorbing atomic photons absorbing.
Heat transfer depends on laser color spectrum and material electrical structures.
So, the heat transfer generally depends for laser is on color and here it depends on material
electrical structure.
The laser absorption depends on feeding material finish and substrate finish since reflection
limits available energy.
What are we trying to say here is when a laser tries to hit at a surface, so you can try
to have incident, then you can try to have reflection.
You can also have little bit of transmission and refraction.
This let us take it as transmission.
You can also have little bit of refraction ok, but the reflection property or the absorption
generally depends on the surface finish of the substrate RA of the substrate or it tries
to see what is the powder surface morphology, so that it does not reflect gets into transmission
or refraction.
It has to absorb right.
So, the electron transport heat by inelastic electron substrate collusion.
So, it just hits the surface and it just penetrates the surface.
The electrons are accelerated to high kinetic energies to impact the substance and embed
themselves delaying the process.
So, electron beam transports heat by inelastic electron substrate collusion.
The electron beam which comes tries to hit at the surface.
When it tries to hit at the surface, the electrons can be accelerated to higher kinetic energy
by using electrical lenses or electromagnetic lenses or electric field lenses whereas, in
laser what we do is we try to use an optical phenomena to focus and try to increase the
kinetic energy.
Material finish and electronic structure does not affect the heat transfer unlike in laser.
This is a very big advantage of electron beam.
So, electron beam this is the biggest advantage as compared to that of laser.
So, it will have high kinetic energy and it will have very high heat transfer efficiency.
So, that means to say the process efficiency goes high when we use electron beam as compared
to that of laser.
The magnetic field can move electron beam at around about 1 kilometer per second.
Look at the speed.
If you can do it at 1 kilometer per second, you can sweep very fast in creating the outer
layer and the hatch patterns you can create it very fast.
So, the machine building time is reduced to a large extent by using electron beam.
The scanner mechanical limit limits the laser beam to 5 to 7 meters per second.
So, laser what happens is you will use laser, then you will use a galvos, galvos system.
This galvos system is predominantly mechanical base it will be sweeping a light source, sweeping
the light source to focus on the workpiece.
So, this puts a limitation to 5 to 7 meters per second.
So, this makes electron beam faster as compared to that of laser.
Now, let us try to compare three processes.
One is laser assisted or laser used powder bed fusion method.
The second thing is electron beam I said machining here, but you can try to do it as electron
beam or electron beam powder bed fusion and then we have laser directed energy deposition.
Directed energy deposition means you will have a metal powder coming through a nozzle
and then it tries to hit at the workpiece and then you have a laser which tries to hit
at the workpiece.
So, this is laser, this is nozzle and the nozzle will have metal powder.
This metal powder flow rate is controlled and then when it tries to hit at a surface,
the laser also tries to hit at a surface.
It can be used for sintering or it can be used for melting.
So, laser laser directed energy deposition, the process called LENSS laser engineered
net shaping predominantly uses the same technique.
So, here energy source the thermal source is going to be laser and here also it is going
to be laser and the next one here in between is going to be electron beam.
A stream of electrons, stream of photons and again here stream of photons.
Let us look at layer thickness.
That is layer thickness is from the powder bed to the sample development bed, part manufacturing
bed.
This is powder bed and this is part manufacturing bed, ok.
So, you will always have a recoater or a doctor's blade which tries to take powder from here
and smear it on top of a surface.
When it smears on top of a surface, it always decides the layer thickness.
So, the layer thickness in laser it would be 20 to 90 microns whereas, in electron beam
it can go to 50 microns, but in laser directed energy deposition it varies from 100 microns
to 1000 microns.
So, here if you see this is a incoming powder.
So, when incoming powder hitting a surface on the workpiece, it does in one layer if
you see it is like cladding when several cladded layers form together it forms a three dimensional
object.
The minimum wall thickness, what is minimum wall thickness?
This is what is the minimum.
Suppose you have a substrate like this, have a substrate like this, this is called as the
minimum wall thickness.
This minimum wall thickness for laser powder bed is 0.2, in electron beam it is 0.6 and
in LDED it is also 0.6, accuracies are 0.1.
So, millimeter that means, to say it is talking about 100 microns accuracy in laser powder
bed fusion.
Here it is 300 microns in electron beam melting it is 300 microns and in laser directed energy
deposition it vary it is 0.4 that is 400 microns plus or minus ok.
If you are looking for a very good accuracy, we go for laser powder bed fusion.
When you are looking for faster, then we go for electron beam.
Now, let us see the build rate.
The build rate varies from 5 to 20 centimeter cube per hour, it is very slow centimeter
cube per hour.
So, it is approximately if you say take a volume of a 15 centimeter scale, it is around
about that.
So, all direction 15, 15, 15, a scale of 15, 15, 15.
So, but generally what happens, this centimeter cube we never build a solid object like this,
we will have so many other features coming in right.
We never build a solid object until and unless you want to do some mechanical property study,
we always have multiple features in it.
So, this build rate whatever it is might occupy a larger volume.
So, 5 to 20 centimeter cube per hour and if you see electron beam, it is 80 to 100 centimeter
cube per hour, it is very fast.
But the sacrificing thing is you will have accuracies compared to laser bed, it is poor.
The layer thickness is less, so the accuracies might also be little higher.
So, if you have roughness, you see this fellow gives the best roughness, laser powder bed
fusion gives the roughness.
So, roughness what we are talking about is the RA.
When we are trying to talk about accuracies, it is the dimensional accuracy, here it is
surface finish, here it is dimensional accuracies ok.
So, the geometric limitation here it needs supports needed.
So, here it is less support needed, here the same limitation as a typical 5 axis milling
machine has as far as laser directed energy deposition.
In 5 axis machine, you have all freedoms to do it.
So, when we look into the material, today there are so many exotic materials which are
coming into application because the customer requirements have become stringent.
For example, they look for high strength, high toughness, high ductility material for
may be aerospace automobile application.
So, now we are shrinking to develop or there is lot of development going on in the exotic
material development.
So, here the process parameter optimization is always difficult in each of these processes
and again generating these powders is also a big challenge in a consistent manner that
itself is a huge challenge, there is lot of work going on.
So, for metal automization people are working on nozzles, what is the spray it has to happen
and other things.
So, ferrous alloys, titanium alloys, nickel and ceramic are used as material here.
So, here in electron beam, it is just the conducting materials alone can be used to
use titanium alloys, chromium cobalt, tool steels, nickel alloys and cobalt and copper
alloys.
When we talk about laser DED, here again you can use everything what we used here, it is
basically depending upon the material and the electron beam.
So, the productivity versus cost it is very good.
So, here it is medium, we will say why it is medium and it is good here.
So, these two processes are the costs of the initial costs are very low.
In electron beam, the costs are very high, we will see that it why is it.
So, it is costs are very high.
So, the residual stresses, residual stresses which are introduced are medium here, medium
here and low here.
If you ask this will be the highest, next highest will be this and the third highest
will be this.
What are residual stresses?
When we are trying to sinter or melt the metal powder, it tries to shrink.
When it tries to shrink, it tries to introduce some of the tensile stresses and in the top
surface, it will have tensile stresses and in the bottom surface, it will have compressive
stresses.
So, these two stresses in one layer also it can happen or between layers also it can happen.
It can happen intra layer or inter layer and once it happens, it tries to warp the material.
So, these stresses has to be removed.
So, what people do is after doing all this fabrication, they try to do a small heat
treatment to anneal the sample such that they can get the best out of it.
So, part complexity can be very high in laser powder bed.
In electron beam, it is low and in directed energy because the wall thickness, the undercut
and all those things as far as laser directed energy deposition method, it is very difficult.
But in laser powder bed fusion, it is good and in electron beam machining, you are having
to focus the undercut and all is very difficult with respect to electron beam.
So, it is medium.
So, typical applications you can see tooling, implant, jet engines, prototyping.
Here it is almost the same and here it will be predominantly used for repair of blades,
vanes, shafts, coatings, etcetera.
So, here we predominantly use it for repurposing and recoating.
So, the necessity of the support, this is a repeat of this.
It is medium, it is low and it is normally none which is the necessity for support structure.
If you look into all those things, let me circle the best parameters.
So, this is best, this is best.
So, support needed is less support needed.
This is good, this is good and this is good as far as the costing is concerned.
This is residual stresses are very low.
This is good, part complexity this is good and you can see here it is application necessity
is low, this is good.
So, now you see you are having several of these things as advantages here laser and
several you will have with electron.
So, you have to hit a trade off while buying a machine for additive manufacturing.
So, this is how a typical electron beam powder bed fusion setup looks like.
You will have a electron here if you see this is completely called a electron gun.
So, electron gun means it develops a stream of electrons and it pushes into the system.
This portion of the system is predominantly for focusing.
This portion is predominantly for again it continues focusing.
It is predominantly used for powder feeding and the last one is called as for processing.
It will have four stages.
So, electron gun stage 1, then it will have focusing 2, then it will have powder feeding
3 and then it will have powder processing 4.
If you look at it very nicely, so this portion completely will be vacuum assisted.
That means to say the entire process of feeding will be in vacuum along with machine building.
Today we are also trying to remove this portion and have only this portion as vacuum, but
it is a good idea to have the entire system.
So, why is electron beam very expensive?
One of the reason is vacuum assisted.
You have to create vacuum two stages vacuum will be there depending two stage vacuum will
be there.
One is called as the primary stage and the next one is called as the secondary stage.
In the primary stage you try to move from atmospheric pressure to 10 to the power minus
3 torr or 10 to the power minus 4 torr you go and from then on you go for a higher torr.
So, we also try to remove oil small oil particles vapors and the dust whatever is there that
vapor.
So, vacuum is there.
So, this makes it expensive and the next one is the electron gun.
Predominantly these electron guns cannot be switched on and switched off at regular intervals.
Laser for example, after the process over you can switch off the laser source, but electron
gun it is always difficult to switch it off and then switch it on.
In the sense it is not a heavy job, but I am saying it is not healthy for the system.
So, once the electron gun is switched on it keeps running the electron gun keeps running
continuously.
So, this makes the system again expensive.
So, this one is a two stage vacuum electron gun and the next large area where vacuum has
to be made.
So, all these things makes electron beam expensive.
In Indian terms if we talk about a very good decent electron beam machine for an area of
around about 1 foot by 1 foot by 1 foot volume if you are looking for it is typically around
about 10 crores that is the cost of the machine whereas, laser in the same spectrum you can
get it somewhere between 60 lakhs to 80 lakhs.
And wherever I wanted to have a vacuum I purge with gas and make sure the environment
around the sintering portion or the melting portion is maintained neutral.
So, that is easy gas cost is not so expensive.
So, that is what people are trying to even now by laser beam in compared to that of electron
beam.
So, laser powder bed fusion is also known as laser beam machining this was simplicity,
but if you try to use the same terminology in machining yes electron beam machining is
also there where cutting is the predominant phenomena.
It is similar to that of laser powder bed fusion, but uses an electron beam as a energy.
Moment I use electron beam then I cannot use optical lenses I have to use this magnetic
field lenses.
Electron beam machining melts powder using a scanning high energy electron beam canon
scanning.
This is where we we were referring to about 1 kilometer per second scanning ok.
The electron beam machining method have greater resolution surface roughness and layer thickness
than LPBF which we compared.
The large melt pool creates a larger heat affected zone.
The kinetic energy of the beam electrons heats the metal powder which accumulates a negative
charge as it absorbs the incoming electron this point is very important.
So, the electron beam heats the metal powder because of high kinetic energy melts it which
accumulates a negative charge as it absorbs the incoming electrons.
Because negatively charged particles ripple each other this may cause powder bed expulsion.
So, what do you mean by that?
So, here there is lot of charged particles.
So, each one try to ripple.
So, it tries to throw them out like this it is like a flower pot during Diwali we celebrate.
So, it is almost like that.
So, because negatively charged particles ripple each other this may cause powder burn expulsion.
This causes a powder cloud and or a more diffused beam.
So, all these things when it go here when the new beam tries to hit it tries to diffuse
beam which increases the melt pool.
So, normally what happens you are focusing here now.
Now, you will have lot of disturbance coming.
So, now the electron whichever is there it is trying blurred and it comes down.
So, it tries to do.
So, that is what we are trying this causes a powder cloud and or a more diffused beam
which increases the melt pool this is the melt pool area this is melt pool ok.
The electron beam gun are more effective than laser beam because the bulk of the electrical
energy is converted into a beam while the rest is dissipated as heat the bulk of the
electrical energy is converted into beam.
So, this makes the process efficient.
So, under the influence now we will get.
So, the electron gun is there that tries to create electrons.
So, these jet of electrons enter into the the focusing system when they enter into the
focusing system you see magnetic focusing lenses are there why because it is e which
is there and this e can be focused or defocused by using magnetic field the speed of e can
be increased and decreased by the magnetic field.
So, the magnetic focusing lenses are used basically you pass current through the coils
and this creates a magnetic field the e which goes inside the magnetic field gets now focused
down to a small spot.
So, you can see here this is focusing.
So, here it tries to go down and parallelly when you want to do a scanning operation of
the beam.
So, what you do is you have magnetic deflection coils which allows the beam to move left and
right.
So, that you try to create a larger area if you look at the plan view.
So, initially it was a spot here now it is a spot here now it is a spot here.
So, it will try to move in this and then try to center powders.
Under the influence of electric and magnetic field the free electron in vacuum can be accelerated
creating high energy narrow electron beam because of the magnetic field focus conversion
of kinetic energy into thermal energy is the fundamental principle of electron beam
conversion of kinetic energy into thermal energy is the fundamental principle of electron
beam.
Now, let us discuss about electron beam mechanisms when electrons collide in a vacuum their kinetic
energy is converted to heat.
When electron beam accelerates and collides with powerful electric field and magnetic
lenses their power density can reach up to 10 to the power 6 watt per millimeter square.
And the localized temperature can raise at a rate up to 10 to the power 9 Kelvin per
second it is almost like a rocket speed.
So, you hit it immediately the temperature goes high once the temperature goes high then
the powder melts once it melts it diffuses heat into the next powder and the electron
beam scans.
So, now, you see all these phenomenas go parallel.
So, you get proper output or a good quality output by using electron beam.
So, the densities can go 10 to the power 6 watt per millimeter square and the temperature
rising rate will go to up to 10 to the power 9 Kelvin per second.
So, this depends on the power and also this part diameter the basic required equipments
to generate an electron beam are a power supply.
So, you need to have a power supply how do you create electrons you have two electrodes
you have negative you have positive.
Now, between these two you are trying to connect negative you are trying to connect it to a
positive.
So, these two are there very high potential you apply very high potential what will happen
you have dielectric in between.
So, this dielectric whatever is there it breaks and then it tries to create a spark or an
arc.
So, this process of avalanche of electrons getting created and getting focused to a smaller
point is done by this electron beam.
So, the avalanche of electrons come out you because of your potential whatever you apply.
So, the power supply is very very important.
So, power supply then is the electron gun I told you the source, then an anode magnetic
lenses, then electromagnetic lenses which is used electromagnetic lenses and deflection
coil which is used for creating the electron beam trying to hit at the workpiece.
Power source is needed for an electron beam to be created low or high level voltage equipments
from 5 to 30 or up to 70 to 150 kilo voltage is applied between the electrodes.
So, is available depending upon the process very high power source you need.
Next the electron guns cathode is heated, cathode is heated by a low voltage filament
evaporating electrons from it as a cathode tungsten is preferred.
So, we use tungsten cathode for generating these electrons the evaporated electrons are
accelerated towards the positively charged anode and placed after the electron gun.
So, the electrons whichever comes towards the.
So, what will happen electrons e will come and here let us assume there is a ring which
is positive.
So, all these things will come to this.
So, the electrons are accelerated towards the positively charged anode that are placed
after the electron gun this is the electron gun.
So, what will happen they will all be pulled and then go here from here what you do is
you try to focus it down.
You it will not get attached here not get attached here, but it will try to go and
then this will try to push it will come down and anode aperture that is what I said this
aperture means this is aperture a donut something this is a aperture and here you have your
electron this is your electron gun ok.
So, an anode aperture creates electron jet that moves towards the magnetic lens after
this you have the magnetic lens which is there these are magnetic lens this is anode ok.
An anode aperture creates an electron jet that moves towards the magnetic lens these
components block divergent electrons and provide a strong electron beam.
So, it gets moved here then this magnetic then it all gets expanded.
So, now, what you do is you try to focus it down that is what we say here the.
So, formed beam is focused and deflected by the electromagnetic lens and deflection coil
to precisely position the part to be printed.
So, this is what we are trying to talk about.
So, this is what.
So, these are deflection coils these are focusing lens and this is what is the this anode orifice
you have right.
So, through this and you have a thermal this is tungsten tungsten carbide electron is there
then you have a biased cup where you give the higher supply voltage.
So, if you look at the electron beam source the gun electron types there are various types
of electron guns the three most common ones are tungsten filament which is heated a very
high temperature.
So, you apply a high potential.
Next is lanthanum hexaboride which you have like this LAB6 this is filament and this
filament is nothing, but a wire ok then lanthanum hexaboride you have this and then the last
one is field emission gun FEG field emission gun you have a Taylor's cone which is created
I would request you all to see what is Taylor's cone which is created in field emission.
So, this will try to give you an idea how these guns work.
So, this field emission guns anyone is used in the electron gun to create the electron
beam.
So, after electron is getting created from the gun it moves.
So, in electron beam optics and positioning is the next important thing which you have
to study.
So, wherein which we will try to study about stigmatization and then electromagnetic lens
the electrons accelerated by beam power lacks focus and control.
So, the electron which gets accelerated they just get accelerated by beam power, but lacks
focus.
So, this focus has to be done on to a spot.
So, for that we use the electromagnetic lenses focusing shaping and positioning you remember
shaping.
So, we studied in laser about TEM 0 0 mode, TEM 1 0 mode, TEM 1 1 mode etcetera etcetera
we studied.
So, these things are shaping, positioning, shaping and focusing the electron beam is
done by the electromagnetic lenses.
Electron beams are focused using lens albite and electromagnetic ones made by magnetic
field much like a optical device.
Like a lens you have in laser what we do is we have a lens and then on top of the lens
we do a thermal barrier coating because the lens when it is hit by a laser beam it will
try to melt.
So, in order to avoid it we do a thermal barrier coating transparent thermal barrier coating
on lenses is a big challenge, but nowadays technology has come up very well and there
is matured.
So, you have a lens which is coated with thermal barrier coating.
In the same way here we do not use optical devices we use magnetic field devices.
The lens is constructed by winding wire around a coil much like a solenoid.
So, what is a solenoid?
You have this is a coil which is one and then you have a lever.
So, this lever will go up and down by passing current to it.
So, or this lever will get stiffened by passing current to it almost the same thing.
So, winding wire around a coil much like a solenoid on the other hand is wound across
a very short length making the magnetic field less dense towards the center of the lens
than a solenoid which generates a uniform magnetic field.
We are trying to take solenoid along with this because solenoid is one thing which you
would have seen or you would have done experiments in your school days.
So, solenoid when you compare to that of solenoid how does it look like?
So, here makes the magnetic field less dense towards the center of the lens than a solenoid
which generates a uniform magnetic field.
So, when we understand little bit more about electromagnetic lens and electron will initially
encounter a clockwise force.
You have to go back and relook into the right hand rule, left hand rule, Lorentz force all
these things.
So, when you go through those fundamentals you will understand this more in detail.
An electron will initially encounter a clockwise force around the entrance as it travels through
the lens.
So, it encounters a clockwise force.
The force starts to point in the direction of the opening center as soon as the electron
gains some velocity in the direction.
So, assume that you have a box inside a box you have a ball you just keep rocking the
ball inside it.
So, after some point of time the ball gains velocity and then the ball will try to exit
out from the box.
It is almost the same.
The force starts to point in the direction of the opening center as soon as the electron
gains some velocity in the direction.
The windings and the other components must be built with great radial symmetry to prevent
deflection in the lens focusing ability.
This is a huge challenge to fabricate because we are talking about electron beam and the
positioning we are talking about in few hundred microns and it should be uniform there should
not be any disbalance in the spot focusing.
So, spot focusing is we always assume it is Gaussian distribution, but it can also have
like this skewness can also have skewness.
So, if you have skewness then it becomes very difficult for you to get a good quality output.
An electromagnetic lens generated picture is rotated and inverted by a force acting
clockwise.
So, nevertheless because the spot form is typically circular this is not an issue in
the majority of the heating applications.
So, this is how it is.
You will have these are the electron beams which come.
This is a north pole, this is a south pole.
You have wire coils which are wound.
So, these coils will be going around.
So, this is magnetic field.
These are white lines are magnetic field.
You can see how this magnetic field tries to interact with the electron beam and try
to focus the electron beam to a spot to a spot right.
So, then at this spot you try to do melting and you vary the positioning so that this
can move either the straight line can move this way or this way to get a scanning and
then you start doing it.
So, you can see wire coils.
These are all wire coils and these are all the yoke which is used to create electromagnetic
field.
The next one is electron beam optics and positioning.
So, we see here TIG matters due to electromagnetic lens non uniformity and filament geometry
the beam may initially be elliptical rather than circular.
So, whatever hits at the workpiece will be elliptical as compared to that of circular
ok.
So, this phenomena is called as astigmatism is the term for this condition which TIG matters
can treat.
So, to convert this into this we use TIG matters.
Four solenoids with magnetic quadruple makes up a TIG matter which is a device according
to which quadrant of the quadruple field and electron is in.
It will either experience force towards or away from the center of the field ok according
to which quadrant of a quadruple field and electron is in it will either experience force
towards or away from the center of the field.
The beam can be made to be more or less elliptic by varying the strength of the current in
the opposing pair of solenoids.
So, this whatever we are doing you try to play with the current such that this astigmatism
or the elliptics can be converted into circular.
A well collimated electron beam that can focus down to a tiny spot electrons scatter when
they hit gas molecules in the fluid media.
So, when an electron is coming it tries to hit at assuming this is a fluid or air is
there it tries to hit and it tries to deflect out.
So, this is what we are saying this is electron ok.
A well collimated electron beam that can focus down to a tiny spot, but if this electron
passes through a gas fluid media it tries to get scattered.
This scattering reduces the beam energy at the heat location and increases the spot diameter.
So, when you when it tries to get deflected so, what happens the heat the heat density
what is heat density milli joule per millimeter square or whatever it is.
So, this density decreases electron beam must operate in vacuum for these reasons.
So, this fluid whatever is there has to be removed.
The fluid here can be air it can be liquid, but predominantly we talk about air because
why is this this vacuum will try to increase the energy and decrease the spot diameter.
So, till now what we have gone through is all about electron beam processes.
We have compared various process like laser powder bed fusion.
We have compared electron beam powder bed fusion and laser directed energy deposition.
We have compared this on various parameters and then we saw why is electron beam machine
expensive it is expensive because of its existing subsystems.
The subsystems are you will have a electron gun, then you will have magnetic field lenses,
then you will have powder feeding mechanism, the last one is going to be the vacuum assisted
building space.
So, all these things are subsystems of electron beam powder bed fusion.
We will see little more details on powder feeding in the next lecture because if the
powders are not fed properly, then you will not get a sound quality output.
So, points to ponder at the end of the lecture is the basics of electron beam and its mechanism
is thought similarities and difference between electron beam and laser beam is being discussed.
So, assignment if you can google and find out few parts which are made out of electron
beam and you write your inferences why is it not made by laser and we have chosen electron
beam.
If you can look out for answers that will be wonderful and all these assignments are
only for you to do self learning you need not submit the assignments.
Thank you very much.
