Lecture: 27

IIT Kanpur July 201
20 followers
1 Video View·Dec 1, 2023
So, in the last class we were discussing about the step response of series RLC circuit. So,
in this class we will continue our discussion on series RLC circuit and we will also see
the condition when your RLC are connected in parallel and then you provide the step
response to that circuit. So, let us recap what we were discussing in
the last class. So, in the last class we discussed about the step response of a series RLC circuit
and we discussed that at time t is equal to 0 when the switch is closed the equation for
the particular circuit is L di by dt plus Ri plus V is equal to Vs where the Vs is the
voltage source. Now, when we rearrange then we got the second order differential equation
and then we ah discussed that the solution of the equation ah which we ah collected based
on the ah mesh analysis of series RLC circuit has two components.
One is natural response and another is forced response and we saw that the total response
is the sum of forced response as well as natural response. To get the natural response
we set Vs equal to 0 and we found the three conditions like over damped, critically damped
and under damped situation and we got the three ah voltage values under these three
conditions and then we discussed that ah the forced response is nothing, but the steady
state value across the capacitor that is nothing, but the voltage Vs.
And finally, we got the three ah conditions that is over damped case, critically damped
case and under damped case and what we were discussing in the last class is that we have
got these three equations in terms of two unknowns those are A 1 and A 2 which we can
the value of these A 1 and A 2 can be found with the help of seeing the initial and final
conditions like initial voltage or ah voltage across capacitor initial current through inductor
and similarly the final values so on. So, what we will do we will ah try to understand
the fact with the help of one example. So, what we will do we will ah take this example
in this example the switch is opened at time t is equal to 0 and the resistance R which
is given in the ah figure is 5 ohm. So, what happens the switch is initially closed
and when it is opened the circuit is converted into series RLC circuit. So, now, let us try
to find out the value of current I at any time t and value of voltage at any time t.
So, if you see this particular figure when this switch is initially closed for time ah
t less than 0 what happens that this particular circuit will give inductor as a short circuit
because it is switch is connected for very long period and the capacitor will be open
circuit because it will be charged to certain value and it will act as a open circuit. So,
what we left in the circuit is only these two resistances. So, based on these two resistances
we can find what will be the value of voltage across capacitor at time t is equal to 0 and
what will be the value of current which is flowing through the inductor at time t is
equal to 0. So, that would be our starting point now given
in the question as a 5 ohm now switch is closed at time t is equal to 0. So, particularly
at that time that is at time t is equal to 0 ah we need to first find out the value of
current flowing through the inductor. So, what we will get since we can see from the
figure that only these two resistances are in the circuit and current flowing through
the inductor is nothing, but current flowing through the resistances.
So, what we get is that 24 volt is the voltage source and value of R is 5 value of 1 ohm
resistance is added in series with 5 ohm resistance. So, total resistance of the circuit is 6 ohm
and which is applied across 24 volt. So, what we get the initial current that is current
at time t is equal to 0 is 4 ampere. Now initial voltage across the capacitor would
be same as the voltage across 1 ohm resistor. So, you can see from the figure. So, we need
to find out the value of the voltage across the 1 ohm resistor since we know that the
current which is flowing in the circuit is 4 ampere which we just calculated. So, the
voltage across the capacitor will be 1 ohm multiplied by 4 ampere that is 4 volt. So,
we get the initial voltage across capacitor is nothing, but 4 volt.
Now when time t greater than 0 the switch is opened that means, the 1 ohm resistor is
now disconnected. So, when you open this switch at time t is equal to 0 this particular resistor
will be disconnected from the circuit. Now in the circuit we will have only R of 5 ohm
1 Henry inductor and 0.5 Farad capacitor. So, we see the typical case of series RLC
circuit. Now in this case what we have to do we have to first find out the characteristic
roots because it is a series RLC circuit we discussed what will be the values of ah the
characteristic roots. So, let us find out the value of alpha alpha is nothing, but R
by 2 L and we get the value of alpha as 2.5 omega naught is nothing, but 1 by root LC
and the value of omega naught is 2. Now you see that alpha is greater than omega
naught it means that we have the over damped condition. So, in this case the over damped
means your value of the characteristic roots would be minus 1 and minus 4 which you can
find from the formula that is sigma 1 2 is nothing, but minus alpha plus minus root of
alpha square minus omega naught square. So, since it is a over damped natural response
the value of voltage across capacitor at any time t can be given as a force response that
is V f plus A 1 e to the power minus t plus A 2 e to the power minus 4 t. Now V f is the
force or the steady state response. So, if you see from the ah figure which is the modified
circuit when the switch is opened. So, the V s the ah final value that is value of V
f is nothing, but V s because when the capacitor is charged to its value the current will be
0. So, at a steady state the value of V f would be 24 volt. So, we can now write that
V t is nothing, but 24 plus A 1 e to the power minus t plus A 2 e to the power minus 4 t.
Now next task is to find out the value of A 1 and A 2. Now from initial condition that
is V at time t is equal to 0 we know that the value of voltage was 4 volt which we just
calculated. So, if we put t is equal to 0 in this equation we get the 24 plus A 1 plus
A 2. So, finally, we get A 1 plus A 2 is nothing, but equal to minus 20. So, this is
what we get from voltage across the capacitor at time t is equal to 0.
Next we know that the current through inductor cannot change abruptly and it is the same
current which flows through at time t is equal to 0 plus means even when we open the switch
the current across the current through the inductor cannot change abruptly. So, what
will be the since it it is the series circuit. So, the current which is flowing through inductor
at time t is equal to 0 will continue to flow through the capacitor also. So, we can say
I naught is nothing, but C d V naught by d t is equal to 4 ampere which we calculated
previously. So, now, d V d V by d t at time t is equal to 0 is nothing, but 16. So, this
you can calculate from the equation. Now before using this condition that is d V
by d t at time t is equal to 0 we have to first take the derivative of V. So, we know
that this is the value of V at time t. So, let us take the derivative of this when we
take the derivative we get the value of d V by d t as minus a 1 e to the power minus
t minus 4 a 2 e to the power minus 4 t. Now you will put t is equal to 0. So, you get
another equation for a 1 and a 2 that is minus a 1 minus 4 a 2 is equal to 16. So, now, you
have two equations for a 1 and a 2 first you got from here and second you got from
here. So, you you can use these two equations and
find out the value of a 1 and a 2. So, when you get the value of a 1 at a 2 you can put
the values in the value for voltage at any time t and you get the expression for voltage
at any time t as shown in the equation. Now since the inductor and capacitor runs in series
the inductor current is the same as the capacitor current. So, what we can say? We can say inductor
current I can be given as C d V by d t. So, when you differentiate this and multiply
by C that is the capacitor you will get the value of current I at any time t also. Now
if you put the value of t as 0 you will get the same expression which we derived for current
I at any time at time t is equal to 0 which is our expected result. So, in this way you
can calculate the value of unknowns that is a 1 and a 2 with the help of initial values
that is inductor current and capacitor voltage.
Now let us move on to the second case that is a step response for a parallel RLC circuit.
Now in this case suppose the parallel RLC circuit is shown is in this figure here what
we are doing? We are initially keeping the ah switch closed at time t is equal to 0 we
are opening up the switch. So, that we get the parallel RLC circuit at time t less than
0 the current source will be short circuit. So, when we open it then it will be converted
into parallel RLC circuit. Now at time t is greater than 0 let us apply KCL at the top
node. So, what will happen the value of current I s would be divided into 3 circuit elements
that is R L and C. So, what would be the value of current flowing
through resistance R that is V by R V is nothing, but voltage and any time t across the capacitor
plus I that is the current I which is flowing ah through the inductor at any time t plus
the capacitor current capacitor current can be given as C dv by dt and the sum of these
3 currents will be equal to the value of source current that is I s. Now we know that V is
nothing, but L di by dt. So, we put the value of V in this equation and when we rearrange
you will get the final equation as d 2 I by dt 2 plus 1 upon R C di by dt plus I by
L C equal to I s upon L C. So, this is what you get from the parallel combination of the
circuit. Now the complete solution will be consisting
of natural response as well as forced response. So, you can write the total current I is nothing,
but forced response and natural response of the current. Now natural response of the current
is same as we got in previous section when we discussed source free parallel RLC circuit.
So, we can write those equations. So, what we got that natural response is nothing, but
in case of over damped it is A 1 e to the power sigma 1 t plus A 2 e to the power sigma
2 t where sigma 1 and sigma 2 are the characteristic roots of the governing equation. And in case
of critically damped the natural response was A 1 plus A 2 t into e to the power minus
alpha t alpha was the damping coefficient. And in case of under damped we got e to the
power minus alpha t into A 1 cos omega dt plus A 2 sin omega dt where omega d was the
damping frequency. Now these three we got when we discussed about the source free response
that is natural response of the circuit. Now forced response is the steady state or
the final value of I. So, if you see the circuit when the switch is opened for very long period
this inductor will be short circuit. So, whole current that is I s will flow through
the inductor and you can say that the final value of current which is flowing through
inductor is same as source current that is I s. So, you will add the value of I s in
place of the I f t that is the forced response. So, you will get the total value of current
I t is nothing, but I s plus natural response of the circuit in case of over damped. Again
I s plus critically damped response of the circuit when source is not ah available. And
in case of under damped we get I s plus the natural response of under damped circuit.
So, these three we get based on the various conditions with ah respect to your ah the
damping coefficient and the natural ah frequency of the circuit. So, that is alpha and omega
naught. So, under various condition you will get these three these three values for current
I t. In case of over damped your alpha is greater than omega naught, in case of critically
damped alpha will be equal to omega naught and in case of under damped alpha is less
than omega naught. So, now, in this particular set of current
equations you know that the A 1 and A 2 are the two things which are unknown. So, how
we can find we can again use the initial values of current and voltage that is current flowing
through the inductor and voltage across the capacitor to find out the value of A 1 and
A 2. Now, how we will do let us take one example. So, that the things are more clear. Here if
you see the circuit the 4 ampere current source is connected across the inductor. So, at time
t less than 0 when the switch is open the current is flowing only through the inductor.
So, you can say that at time t less than 0 the circuit is divided into two parts. So,
one part is where the current source is available second part where voltage source is available.
So, at time t ah less than 0 when the switch is open the current will be flowing through
the 20 Henry inductor. So, it means that you can simply say current
i at time t is equal to 0 is nothing, but 4 ampere this you can get easily from the
circuit. Now, you see that the voltage which is connected across the ah the second part
of the circuit is 30 u minus t volt. So, what does it mean? It means that at time t less
than 0 the value of voltage is 30 volt at time t greater than 0 this value becomes 0
volt means when the switch is closed this voltage source is short circuit.
So, this ah is something which you have to keep in mind because here the unit step function
is u minus t it means that the value of unit step function is like this where you have
a value at time t is equal to ah less than t is equal to 0, but it is 0 when t greater
than 0. So, with these two things let us proceed to solve the the circuit for t less than 0
when the switch is open. So, we found that the initial current which is flowing through
inductor is 4 ampere. Now, u minus t is equal to 30 when t less than 0 and 0 when t greater
than 0. So, the voltage source is applied to the circuit only when t less than 0.
Now, at t is equal to 0 minus that means, just before the switch is closed the capacitor
acts like a open circuit and voltage across it is the same as the voltage across 20 ohm
resistor connected in parallel with it. So, if you see this segment of the circuit the
voltage because the switch is open for very long period this will ah the capacitor will
act as an open circuit. So, the voltage across capacitor will be ah same as the voltage across
20 ohm resistance. Now, at time t less than 0 the value of voltage
source is 30 volt and these two are in series because the current will flow through this
direction. So, what will be the value of voltage across 20 ohm resistor which is in parallel
with capacitor? You can simply use the voltage division and you will come to know that the
value of this voltage at time t is equal to 0 is nothing, but 15 volt. So, this is our
initial voltage across the capacitor when the switch is closed. So, we got two initial
conditions ah current which is flowing through the inductor at time t is equal to 0 and voltage
across capacitor at time t is equal to 0. Now, for time t greater than 0 what will happen?
The switch is now closed and we have parallel RLC circuit with a current source. Now, voltage
source is off because for time t greater than 0 if you see the circuit for time t greater
than 0 this will be 0. So, it means that it will be short circuit. So, now, 20 ohm
and these 20 ohm both would be in parallel. So, what we can say that the value of effective
R which is across the circuit will be 10 ohm because 20 ohm and 20 ohm are in parallel
now this will be short circuited. So, now, we have a case of parallel RLC circuit. So,
we have inductor we have capacitor and we will have another equivalent resistance of
10 ohm which is again in parallel. So, what we can do now? We can apply the equations
which we got in case of parallel RLC circuit. So, characteristic roots we can simply determine
with the help of the values which we calculated previously. So, alpha is nothing, but 1 by
2 R C. So, if you put the value of R and C R is 10 C is 8 millifarad. So, it will become
8 into 10 to the power minus 3 and we get the value of alpha as 6.25.
Similarly, the omega naught is nothing, but 1 upon root L C. So, if you put the value
of omega naught you get the value of omega naught as 2.5. So, here you will see that
alpha is greater than omega naught that means, that this is a case of over damped circuit.
So, what we can say the value of the roots that is sigma 1 2 is nothing, but minus alpha
plus minus root of alpha square minus omega naught square and we get two characteristic
roots. So, what we can write now? We can write the
value of current I t that is nothing, but equal to the force response that is I f t
and here the value of I f t is I s which we just calculated in the case of parallel R
L C circuit and plus the natural response that is A 1 e to the power minus sigma 1 t
plus A 2 e to the power minus sigma 2 t. So, here I s is equal to 4 this is what we we
can see from the figure when the circuit is the switch is closed for very long period
the capacitor will be acting as a open circuit and the whole current will flow through 20
Henry inductor. So, it means that the I s value is nothing, but 4 ampere in the circuit.
So, this is what we got that is I s is equal to 4 ampere.
Now, if you put the value of t is equal to 0 in the above equation you know that I at
time t is equal to 0 is 4 which you just calculated. So, you get A 2 is equal to minus A 1. Now,
if you take the derivative of the above equation d I by d t you will get this expression at
time t is equal to 0 d I 0 by d t is nothing, but minus 11.978 A 1 minus 0.521 A 2. Now,
you know that the ah the voltage which is across the capacitor cannot change abruptly.
So, it will remain as 15 volt and since capacitor is in parallel with inductor the same voltage
will be applied across the inductor also. So, you can simply write the voltage across
inductor is nothing, but L d I by d t at time t is equal to 0. So, this you can use and
find out the value of d I by d t at time t is equal to 0. So, you got the value as
0.75. Now, you put the value in this equation. So, you get the value of A 2 and similarly
we can get the value of A 1. So, now, we have A 1 and A 2 we can simply
say the value of current I t is nothing, but 4 plus you can put the value of ah the
expressions ah value of the components. So, you get this particular equation. So, this
is the final expression of current I in terms of t with this we can close our today's session.
So, in this session we discussed the step response ah for series RLC circuit as well
as the parallel RLC circuit and now we will proceed forward to solve these first order
second order equations in a more easier format. Because in these type of equations till now
what we discussed was ah based on the differential equations those were first order and second
order differential equations, it is sometimes difficult to solve. So, we will use another
technique called Laplace transform and we will try to understand first the Laplace transform
and then we will apply that technique to solve these first order and second order equations
and first order and second order circuits again.
Thank you.
