Đóng ghe mủi nhạn p7🍀vô bích be nhờ kỹ thuật lấy mực cưa lão luyện của chú thợ

Thanh Điền NTĐ
3 người theo dõi
Xin mời bà con và các bạn xem video đóng ghe mủi nhạn phần 7
Bấm Đăng Ký giúp tôi sớm đạt cột mốc 100.000 subscribe
Xin cảm ơn rất nhiều.!
#thanhdienntd#
Let's go, let's go.
Ladies and gentlemen.
Today, my uncle is going to cut the bark.
This is a 12-meter-long, 1.8-meter-wide, 1.2-meter-wide.
It's covered with a star tree and a whole tree.
Today, my uncle is going to cut the bark.
Yesterday, he cut the bark.
Put it on.
This piece is a bit curved.
Oh, it's sharp.
The part where the nose is curved.
You have to pull it in.
Pull it in and cut the back of the tree.
This is the curved part.
Yesterday, my uncle cut the middle part of the tree.
He cut it evenly.
It's a bit sharp.
It's a bit sharp?
He's kidding.
It's a bit sharp.
And here.
There's a piece of bark underneath.
It's a bit curved.
You have to clean it up again?
Pull the bark in.
It's too sharp.
Oh, it's great.
You have to climb out.
Why are you climbing out?
You have to release it.
You have to release it and do it again.
You have a lot of nails.
It's different from the bark you cut.
You have to pull it in.
You have to press it up.
You have to press it up?
You don't just have to close the bark.
You have to close it.
You have to press it up.
You don't have to cut it.
It's too sharp.
What did he say?
It's too sharp.
I will cut the next one.
Do you want to change it?
It won't come out?
You have to release it.
You have to release it first.
Wait, wait.
Come in.
Shake it.
It's so cool.
It's like a dream.
After cutting the bark, Mr. Hoa will...
Mr. Chin is taking the right side.
He's taking the board.
Mr. Hoa is cutting the bark.
Wow, it's so good.
It's even.
I will take the board.
It's on the right side of the nose.
It's too small.
This is the part of the throat.
It's sharp.
You are so good at this.
I've already chopped the leaves off the stem.
Like this one, you see?
I've chopped it off.
Now I'm going to peel it to make it more fragrant.
I've chopped it off to the tip of the stem.
This is the next leaf to be peeled.
I'm going to boil the squids and put them in later.
I'm going to boil the squids now.
It's boiling.
I can see it now.
What?
This is cheap. It's not expensive at all.
This is cheap?
It's cheap.
It's reasonable.
How much is it?
79,000 VND?
79,346 VND.
It's 15,900 VND.
That's right.
The boat is moving.
I'm going to put it in now.
I'm going to pay later.
It's boiling.
The boat is moving.
The leaves are too long.
I've already boiled the squids.
Thao and the boat owner are helping me peel the leaves.
Put it in.
Turn on the stove.
Put it down.
Yeah.
Put it in.
Turn it on.
Turn on the stove too.
Turn it on too.
It's ready now.
Blow out the stove.
Turn it on again.
This is the left-hand side of the steering wheel.
The steering wheel is on the left side.
I'm going to make a slope.
The upper slope and the lower slope.
I just finished making this main steering wheel.
I just cut it and put it in here.
I will continue to make the main steering wheel later.
Oh my god, it's a little rough.
It won't drop.
Now I'm going to make the front end flat.
So it's square and straight.
It's a flat head.
And a short head.
The short end is very bad.
These teeth are too tough.
I'm going to cut the top of the head of the squid
