Beginner Knife Making EP 2 - Forging the shape & rough grinding

inspirational person
170 followers
1 Video View·Nov 4, 2023
Comments are disabled for this video.
So after my extensive research in my kitchen,
this is the shape that I'm going to go with. Now it's ghetto.
As you can tell, I'm a fantastic artist. Maybe it's fuzzy there. Who knows?
But, uh,
I'm going to make it thicker here on my drawing and on my forge because I can
always grind off more. Uh, if I need to make it fine tune and pretty,
I can do that on the grinder. Whereas I don't have enough metal,
then I can't do that.
So I'm gonna make it thicker and chubbier and kind of wonky as I pound it out
through this little hammer here. But, uh,
then I'm going to make it better once we get on the old grinder inside the
grinder room.
All right, well, let's get a hammering.
All right. So I'm just about done with the first kind of blank of,
uh, Sam's knife, little paring knife. Uh,
it's bigger than I was hoping because I don't know.
The steel was thick. Uh, the steel was thick.
I'll show you what it's like at this moment. The handle's too long.
So I'm gonna have to cut the handle down.
But what we're looking at here is this guy.
And so I'm going to cut the handle. We'll cut the handle.
It's still really hot. It just came out of the forge.
You can still see the forge glowing back there. But, uh,
cut the handle down a little bit. I could elongate it,
but I don't think I need to. Um,
I'll maybe just do that with the wood as I'm making it with the actual handle,
but I'm going to take it from here. And because it's softer steel still,
before I do any heat treating,
which I'll talk about a little bit further later, uh,
I'm going to actually go over and grind it down.
So I'm going to take it on the, not the angle grinder this time.
I'm going to take it on my actual belt grinder, uh,
plug a little thing in and go to town, plug a little thing in,
put a belt on and then grind it down to a shape that I think could be sexier.
Let's do it. So I'm throwing on a 36 grit belt, which is like,
really, really rough. It's going to remove a lot of metal quickly.
I'm using what's called a blaze belt. They're kind of expensive,
but apparently they last longer. This is an Ameribraid grinder.
They're an American company out of Southern California.
Super good on Instagram, uh, with regards to getting back to, uh,
as well as through email, uh, very attentive, good machine. I love it.
I got rear ended and was able to fix it myself.
So I took the money from that and bought this, uh,
hence the reason I have a grinder of this caliber by being a straight hobbyist.
But that, yeah, that's, that's, uh, that's where we're at.
We're going to grind down some metal.
So I'm changing this platen thing from the round wheel.
Cause I was having a hard time balancing what I was taking off to the
flat one, but make sure it's level and then go from there.
Pinchy pinchy.
All right. So, uh, got the blade to where I want it. It's a little bit thin,
but I don't know. It'll work.
What I'm going to do is I'm going to drill the holes in it now for the handle
that we're going to use later.
So I need to drill a quarter inch hole using the drill press behind me.
You don't need a drill press you can do with a hand drill,
but the drill press can do a straighter hole. Um,
this is a quarter inch round pin. So I'm gonna do a quarter inch hole.
I'm gonna do it now before I heat treat it.
So just in case the handle gets hard or the tang gets hard, uh,
it is still able to drill through, drill some holes.
So this happens occasionally.
You get one good hole and you're like, Oh, this is great.
And then you go to the next one and it just spins and it squeaks and screeches
and it squeals. And it means that this is too hard. Um,
or it means that my bit sucks and I've tried a couple different bits and it's
not going through. So what do I have to do? Well,
I'm going to try to do it in the actual forge.
So I'm going to take a punch. I'm going to heat this up to red hot.
I'm going to try to punch a hole through it.
So now I have these little guide things. Um,
and that's one of the reasons forging I think is awesome.
Also I'm using a recycled steel.
So never believe something like this might happen.
Let's go ahead and see what happens.
The holes are messed up. They wouldn't drill.
So I tried to punch them out with the punch and it just bent the ---- out of the
knife. So that was, uh, not particularly successful.
Let's see if I can cut it out and drill it out. Maybe hand, uh,
drill it out. And, uh, we'll see what happens. Uh,
I might only do two pins in this. We'll see.
So the last thing I did there was called heat treating.
And basically what I did is I take the knife up to a, uh,
non-magnetic temperature. So really,
really hot and then rapidly cool it in water or oil.
And when I did that,
it causes the molecular structure of the knife to change, making it much,
much, much harder. Uh, when you do that,
it allows you to maintain an edge and basically turns the steel from
being a just random piece of steel to an actual knife.
I did it twice because the first time I did it,
it didn't quite harden enough for me.
The way you test that as you see if it's harder than a file.
So you run a file across the edge and if it skips across the edge,
it means that, uh, you, you've, uh,
hardened it enough. If it doesn't, it bites into the edge.
Then that means it's too soft.
