CÁCH LÀM QUẢ DỨA BẰNG KẸO TỪ LON BÒ HÚC- NGHỆ THUẬT GÓC BẾP]-

NGHỆ THUẬT GÓC BẾP
45 người theo dõi
30 Lượt xem video·23 thg 10, 2023
Hello everyone, today I'm going to show you how to fold a pineapple with a non-woven fabric
This method is also different from the method in the previous video, please follow me
First, you need 2 packs of red ice cream
Today I went to the candy store, they ran out of packages, I had to buy 1kg of ice cream
You use 200g of ice cream like this for me
1 pack of green ice cream, green leaves, A4 size
This pack of ice cream is 2-sided
1 can of beef jerky
1 roll of clear tape
1 needle
This is a needle box, when you run out, you can replace it
1 wire
1 scissors
1 ruler
1 roll of 2-sided tape
This is a small size, about 8cm to 1cm
1 roll of nylon tape
Green leaves
First, you go to the candy store
This is the right side of the candy store, there is an IC symbol on the right side
You fold the top of the candy for me
Then you turn the button like this
You press here
So that these 2 buttons are on the inside of the left side of the candy
This is the right side of the candy
This button will be on the outside
It will be more beautiful when I test the bottom
It does not reveal the bottom of the needle
You do the same for the bottom of the candy
Both ends have a triangle shape
This is the left side
You look carefully
The left side of the candy will be like this
You look at the right side of the candy
I press again to show you
You fold it into a triangle like this
Next, the bottom of the candy
You fold it like this
You just fold it like that
I have marked it here
This is the top of the candy
You fold the paper like this
Here
You fold it like this
Next, you fold it in half
Like this
You tear it off
Then you cut a part
You take a part
This is the bottom of the paper
I fold it into 4, I just cut a part
I will make the top of it
Next, you roll it into a triangle like this
Like this
I do it again
Here
I roll it into a triangle
Then you take a pair of scissors
This is the length of the top of the candy
Cut it for me
Make it equal
You fold it like this
Make it equal to this leg
Here again
Alright
Now you put it on this can
I will put it to release the candy
Release the top of the candy
To make it fit
Make it beautiful
Don't put it in the can
It looks very ugly when it's small
If you put it like this, it looks very ugly
Remember to pay attention to me
Here
Put it like this
It fits perfectly
In the mouth of the can
Now you put it like this
You take a piece of tape
Here
How to make the tape fit
To create a dot
Alright
It's done
Now you will fix the dot on this fruit
I will fix it
You will fix the can for me
I will fix the can for me
Just like this
I have fixed the tape
To make the dot stick firmly like this
You stick a lot of tape to make it firm
To make it bulge
Now I will make the leaf of this pineapple
You put a piece of green tape
Then you cut it for me
10cm
Its length is 10cm
10cm like this
Then you cut into
The tip of this
To make a pineapple leaf
Like this
Here
You cut the tip like this
You cut 15 pieces
The length is 10cm
Here I have finished cutting
15 pieces like this
There
Now I will take the double-sided tape
I will wrap it around the top of the can
You from the top of the can
From the top of the can
You cut for me 1cm
You stick for me
Here
You stick this leg for me
Like this
Here
Stick like this
To make the double-sided tape clear
Clear tape
Wrap around this leg to make it firm
Here
To make it firmly fixed
Here you are
You wrap the double-sided tape
Close to the first layer
Here
Close to the edge
The edge of the leaf
You stick the double-sided tape for me
Here are 2 leaves
You stick the double-sided tape like this
Stick the double-sided tape for me
To get the first point
Next you just stick together
You take the double-sided tape
I'm sorry
I made a mistake
To make it easier for you to observe
Here you take the double-sided tape
Wrap around
Close to the edge
Close to the edge of the leaf
You peel off
You stick for me
Here is the first point
You stick the double-sided tape for me
Compared to the previous layer
You stick it
Make it close together
OK
Done
You stick the double-sided tape
This is the upper part of the leaf
The lower part of the leaf
Next I will go to the glue
To create the lower part of the leaf
You make a circle of double-sided tape
For me to film
Then you stick the glue
You put the IC
Upside down for me
Like this
Put it all up for me
Turn the red IC
Put it all up
I feel it will be more beautiful
Now you just put
The IC to keep spinning
It doesn't look eye-catching
Now I will try to stick
With a layer of double-sided tape
Like this
Next is the second
You stick the double-sided tape
Two
Like this
The distance
The glue is the first
Done
Now I will stick
The second
You put the IC
Upside down
The IC
Into the IC
It will look like this
There
Here
It will stick in there
Next
Let me do it again
You make the second turn like this
This is my second turn
You just stick
Like this
Then you use the IC
I lost the IC
There
You roll around the glue
Try your best
This is the third turn
You put the IC
The double-sided tape
I make it a little bit
Too fast
I don't understand
Some people don't like to do it slowly
But many people don't observe carefully
Always listen to me
Talk like this
Don't pay attention
I don't know where the glue is
Next
Put the IC
Here
Put the IC
There
You just stick like this
To make the middle part beautiful
You stick all the way around
The next turn is still the same
Until the bottom part
That's it
This is my last turn
I do the same
as the other turns
This tip
You put it in the middle of this slot
Next
Here
You take the double-sided tape
Try your best
Do you see my result?
Short but very beautiful
Now I will put the last layer
The double-sided tape
To stick the IC
Here
Look at this
I stick it at the bottom
I take it out
You start to stick the IC
below
Roll around and cut it
Cut it
Try it
So I finished the middle part
I put it in the middle of the slot
I made it from a straw
This is different from the previous way
You see it is very beautiful
I put it here
You put it on a round plate
Then decorate
Or put it on the altar
It looks very cool
I wish you success
in making your turntable
If you find this video
interesting
Please like, share
and subscribe to support me
Thank you very much
Thank you for watching
See you in the next video
Bye Bye
