Lecure 05 Module 1

IIT Kanpur July 201
20 followers
Oct 22, 2023
This is lecture 5. So, in the previous lecture, in lecture 4, we discussed mostly about how
to take a non-linear circuit or rather how to take a non-linear element and do a linearization
of that element. Why do you want to do a linearization of the element? Because we saw that using
using the magic of Taylor series, we could break the incremental, we could break the incremental
voltages of the currents through the non-linear element into linear and non-linear terms.
And under the condition that the non-linear terms are much much smaller than the linear term,
we could neglect the higher order terms and we could essentially say that a whatever non-linear
element we have to deal with under certain operating conditions, we can linearize it.
And what is the, what is so holy about this method of linearization? It will, the beauty
about the of this method is the fact that it will help us to do a linear circuit analysis,
because all our all our knowledge of handling circuits, all our knowledge of handling circuits
work efficiently as long as we can transform them into some sort of linear equations.
So, and in the road to doing that, what did we do? We took an example of an arbitrary
non-linearity and we said that if the voltage across this is V n, the current through this
is f of V n right, this is V i, this is R l. And what did we say? What were the steps?
The step 1 was to find out the quiescent, the quiescent currents and voltages that is,
that is we do a numerical simulation or we do the numerical analysis or we do a graphical analysis
to find out the find quiescent currents and voltages. And let us say after doing some
numerical or graphical methods, we could find that for a certain value of V i, the current
through this network was I sub n and the voltage across this device was V sub n,
which means the voltage across R l is V i minus V sub n, which is nothing, but I n times R l right.
So, we do a numerical analysis to to find these values right. So, perform a numerical
slash graphical analysis to find I n and V n ok. So, now that we have found, what was the next
thing? Next thing that we said was, if if my input was let us say V i plus delta V i, where delta V i
is a small increment right, then I could in principle find out the relationship between the
current that the incremental current and the incremental voltage, let me use a different
color here. So, let us say I had plus delta V i, then obviously there will be an incremental
voltage across a non-linear element. And the current that was I n to start off
will now change to I n plus delta I n. And now the whole whole focus shifts to finding out
this delta V, finding out delta V n and delta I n given we have delta V i right.
So, now the focus shifts there and in order to in order to figure figure it out, what should we do?
So, let me move this here. In order to do that, in order to find out the relationship of the
incremental quantities, what we do? We replace we replace the non-linear element with a resistor.
What is the value of the resistor? The value of the resistor is 1 1 over del f 1 over
del f del V around the operating point V n. What happens to the resistor R L? This R L
remains R L. What happens to the input? Note that since we are since we are concerned about
concerned about the delta V i, the input effectively becomes delta V i correct.
So, this current that we will have after solving solving for this network will be delta I n and
this resistor then the voltage drop that I will get across the linearized version of the non-linear
element will be delta V n right. So, this essentially was the crux of the entire lecture 4
right ok. So, now now that we have delta V n and delta I n. So, let me write down this step also.
So, this step was the second step the second step as in replace all elements in the network
with their incremental equivalent right. So, this network here is the incremental
network right. So, now that we have got now that we have gotten
the quiescent and the incremental. So, what is the final step? The final step is to find out the
total final step is to find out the total I n V right not only the increment.
So, essentially what are we after? We are after if the input is V i plus delta V i
and the and the network consists of an actual non-linear element right. So, this is V n
plus delta V n right and this current is I n plus delta I n. So, what is the what is the final
solution? The final solution will be to find total voltages and currents for input V i plus
delta V i we need to add up the responses from the quiescent and the incremental right.
So, essentially we have found V n and I n right from operating conditions and we have found
small delta V n or rather delta V n and delta I n from the incremental conditions right. We have
found capital V n capital I n from this network, we have found capital V n capital I n from this
network and we have found delta V n and delta I n from this network right. So, once we have found
these two what we need to do in order to find the total we simply need to add them up right.
I did not I missed a step here I did not evaluate delta I n what is delta I n? So, I know that
delta I n is delta V i by R L plus R L plus this incremental resistance right.
What is that incremental resistance? That is 1 over del f del V evaluated at V n right.
So, once I know that this is del delta I n what is my total current? Total current is equal to
I n plus delta V i by R L plus 1 over del f del V n evaluated ok great.
So, again at the cost of repeating myself what did we do? What did we do in order to figure out
the solution of of this network? This becomes a 3 3 step process. One find out the quiescent
currents and voltages or the operating currents and the voltages using graphical or numerical
methods. Step 2 linearize the circuit right sketch the incremental network. What is the
incremental network? The incremental network is nothing, but the linearized version of the
non-linear it is the same network where the non-linear element has been has been replaced
with their linearized version and and all the sources have been replaced with their
incremental equivalent and then you then you find the the incremental currents and the voltages
from the incremental network right and it is easy to find because this incremental network is
fully linear. So, essentially now you are now you end up having two quantities one is the
quiescent or the operating currents and voltages another is the incremental current and voltages.
In order to find out the total you just simply add them up and what is so great about this?
The great thing about it this is that now if V i if delta V i changes right if delta V i changes
if delta V i is let us say 1 millivolt I just simply replace 1 millivolt instead of delta V i
if delta V i becomes 10 millivolts right I I replace 10 millivolts instead of delta V i
if delta V i is 100 millivolts I replace 100 millivolts in place of delta V i and I do the
incremental analysis again. So, you have to do the quiescent analysis once and at the cost of
doing the quiescent analysis once you are able to do all the incremental analysis in a linearized
fashion right. So, that is the power and the strength of this of this method, but note that
you have to be slightly careful you will not you cannot you cannot do this for any values of delta
V i why? Because this incremental this linearized version of incremental equivalent is only valid
when you can neglect the higher order terms and if delta V i keeps on increasing the higher order
terms for the Taylor series will be will be will be non-negligible. So, in a sense there is a there
is a maximum limit of delta V i right beyond which this incremental linearized models are valid
right and that and in this course we will we will not reach that limit, but it is it is it
is always instructive to keep that at the back of your mind and there is one more one more jargon
that is used to that is used to refer to this incremental linearized model right.
So, that is called a small signal model right and what by definition what is small signal?
So, when when the higher order terms of a Taylor series or not a of the Taylor series
of the non-linear element can be neglected with respect to the linear term right we call
the linearized model a small signal equivalent or small signal right. So, from here on in we
will use this term small signal linear or linearized incremental model interchangeably
okay. So, if you if you open up textbooks you will see that this term of small signal model
is used ubiquitously. So, we will also refer to this as a small signal model.
Now before moving forward it is make sense to understand what is the small signal equivalent of
all the elements that we know of right. For example for example a resistor right
say we have this resistor. So, what is the small signal equivalent of a resistor?
So, let me call write this as this is the element and this is the small signal model right. So,
what is the small signal model of a resistor? How will you how will you get the small signal
model of a resistor? Note that how did we get the small signal model in the first place
we needed to characterize the element. So, how do you characterize the resistor? A resistor
is characterized by if I have a voltage V across this element and you have a current
I that is flowing in the small signal the relationship between I and V right the relationship
between I and V is I is equal to 1 over R. So, what will be the small signal equivalent
of this? So, note that the I V characteristics of a resistor straight line and what is the
small signal equivalent? The small signal equivalent whatever this element might be
this is equal to 1 over del I del V which is nothing, but correct. So, the small signal
equivalent of a resistor is a resistor itself and it makes sense because my resistor is a
perfectly linear element. What about a capacitor? What about a capacitor?
So, when you see a circuit element that is a capacitor what is the governing relationship
between of this capacitor? Primary governing relationship is between the charge stored
across the in the blades of the capacitor and the voltage across the capacitor right.
So, the governing relationship is Q equal to C times V right. So, like the resistor
the governing relationship for a capacitor is again a straight line right. So, what is the
slope of this straight line? So, this slope is equal to 1 over R. What is the slope of this
straight line? The slope of this straight line is C right. So, the slope is C anywhere on this
curve. So, essentially this capacitor gets replaced by a capacitor with a value C.
Similarly, if you have an inductor which has a current I going through it, what is the governing
relationship of an inductor? The governing relationship is phi is equal to L I where
phi is the flux I is the current that is going through it. So, essentially if I sketch I here
and phi flux here again I get a straight line. What is the slope? Slope is 1 over L right.
So, again this is a linear relationship. So, inductor remains an inductor no change.
What about a voltage source? What about a constant voltage source? What is its linearized equivalent?
What is this small signal equivalent? So, again let us go back to our I-V characteristics.
What is the V dc? So, what is the I-V characteristics of a voltage source?
So, voltage remains constant regardless of the current. So, this is a straight line
perpendicular to the x axis. So, what is the slope? Slope equal to infinity. So, if I have
to replace this with this incremental equivalent what do I do? I replace it with an element
which is 1 over the slope. So, what is this element? If slope is infinity this is equal to 0
which means the impedance given by this element is 0 which means this is a short circuit right.
So, this is a short circuit. What is it if I have a constant current source say I dc? So, again
let us go back to our I-V characteristics correct. So, this is V dc here.
We go back to our I-V characteristics. What is I-V characteristics of a constant current source?
Again this is a flat line parallel to the V axis. So, what is the slope? Slope equal to
0 which means 1 over slope is equal to infinity. So, you have to replace this I dc with an element
right whose del I del V is or del V del I is infinity right. So, let me slope. So,
this is nothing but del I del V right. This is again del I del V. So, since del I del V is 0
in other words del V del I is infinity which means its incremental resistance is infinity.
So, you replace it with the open circuit right. So, this is this A this is B becomes A open
circuit and in general if we have a non-linear element which has a current voltage relationship
of I equal to f of V I equal to f of V you have to replace this non-linear element
with this incremental equivalent which I mean if all the terms are real right and all the
derivatives are real then we will replace this non-linear equivalent with a resistor of value
1 over del f del f del V right around some operating point V n or I can simply write
in the form of I del I del V around some operating point V n ok. Does it make sense?
