Prüfen von Strom- und Spannungswandlern mit dem OMICRON CPC

OMICRONenergy
9 followers
13 Video Views·Oct 21, 2023
Bei einer Anlageninbetriebnahme werden Strom- und Spannungswandler geprüft, um Fabrikationsmängel oder Transportschäden festzustellen. Weiters wird die richtige Verdrahtung überprüft und die sekundäre Bürde gemessen. Wenn im Betrieb einer Anlage Probleme auftreten, dienen weitere Prüfungen zur Eingrenzung der Fehlerursache. Das CPC 100 vereint viele dieser elektrischen Prüfungen in einem Gerät und reduziert so den Material- und Arbeitsaufwand beim Wandlerprüfen.
Weitere Informationen über CPC 100: https://www.omicronenergy.com/de/produkte/cpc-100/
Interessiert am Prüfen von Messwandlern? – Sehen Sie sich alle Videos zu diesem Thema an: https://youtube.com/playlist?list=PLzmbZeI1bhu-90-fevudkdEDvy1HyTq9u
When an installation is put into operation, electricity and voltage converters are checked to identify manufacturing defects or transport damage.
Furthermore, the correct wiring is checked and the secondary barrier is measured.
If there are problems in the operation of an installation, further checks are carried out to limit the cause of the error.
The CPC-100 combines many of these electrical tests in one device and thus reduces the material and labor costs when checking converters.
The CPC-100 can be operated on a normal 230 V power supply and generates up to 800 A alternating current or up to 2000 V alternating voltage.
In the case of power converters, translation and polarity are usually checked, as well as the magnetization curve and barrier are measured.
The accuracy limit factor or the overcurrent limit factor is calculated based on these values to ensure the correct function of the converter in protection or measurement circuits.
To feed in, the high-voltage cables of the CPC are connected to the primary connections of the converter.
The secondary current is connected from the converter clamps to the CPC's power measurement input.
If a user does not want to open the secondary wiring of the converter, the secondary current can also be measured using a power pliers.
Within seconds, the CPC shows the conversion ratio and accuracy of the converter.
By measuring the phase situation of primary and secondary current, the polarity of the power converter is checked.
The secondary barrier can also be measured in units and phases.
In conjunction with a power amplifier, the CPC can generate even higher currents, up to 2000 A.
This power amplifier is supplied by the CPC with a 20 m long thin cable and placed in the immediate vicinity of the power converter, which shortens the high-voltage cables.
To evaluate whether a converter core is laid out according to its barrier, the magnetization curve can be measured with the CPC.
In an automatic test run, the CPC measures the magnetization curve and shows knee-point tension and current.
In conjunction with the measurement results for wind resistance and barrier, the accuracy limit factor for protective circuits or the overcurrent limit factor for measuring circuits can be calculated.
After the test, the CPC automatically demagnetizes the core and generates a test protocol with all measurement results.
In addition to the test of conventional power converters, the CPC can also be used for the test of non-conventional converters in systems with IEC 61850 process buses.
For voltage converters, the translation and polarity as well as the barrier must be correct.
With the CPC 100, alternating voltages up to 2000 V can be applied primarily to check the translation of voltage converters.
In the translation measurement, the CPC also checks the polarity of the voltage converter.
In addition, it measures the phase angle of the primary and secondary signals.
The high-voltage output is measured internally.
The measurement is carried out secondarily via a voltage measurement input.
The secondary converter voltage can be difficult to measure, especially at low values or when scattering through neighboring components.
By using a non-network-frequent test voltage and frequency-selective measurement, such disturbances can be filtered out.
The CPC can also be used to check whether the barrier lies in the specified area of the voltage converter, as a prerequisite for accurate and secure operation.
In addition, the CPC measures the voltage at the converter secondary circuit and the amplitude and phase of the load current.
According to legal or internal guidelines, the capacity and loss factor of the main insulation of converters is also measured in some voltage levels.
This can be achieved by acceptance or as part of a maintenance program.
In addition to the CPTD1, with a test voltage of up to 12 kV, the CPC enables capacity and loss factor measurements to assess the state of the current or voltage converter insulation.
A CPC replaces a number of devices and can be used for numerous tests of current and voltage converters, as well as the test of power transformers, power switches, grounding systems and numerous other electrical components.
