DIY #47 Trang trí phòng bằng đèn Handmade | Dzi Lê Diy

DZI LÊ DIY
51 người theo dõi
2 Lượt xem video·11 thg 10, 2023
DIY#47 Trang trí phòng bằng đèn Handmade | Dzi Lê Diy
Video này, tụi mình sẽ cùng nhau dùng những miếng Carton cũ, lọ thuỷ tinh bỏ đi để làm thành một chiếc đèn trang trí phòng thật xinh nhé.
Nguyên vật liệu:
- Giấy carton
- Lọ thủy tinh cũ
- Vải bố
- Que thủ công, thanh gỗ
- Dây thừng
- Đèn dây
- Kéo
- Dao rọc giấy
- Bút, thước
- Keo nến
Các công đoạn
00:00 Intro
00:43 Chuẩn bị lọ thuỷ tinh
00:51 Cắt giấy Carton
02:03 Cắt và dán vải bố
06:57 Dán que thủ công
09:01 Dán hoa trang trí
09:34 Dán nắp đèn
09:55 Dán dây thừng trang trí
10:31 Làm quai đèn
10:55 Bỏ dây đèn vào lọ
Hi, welcome to Sia's DIY.
In this video, we will make a 2-meter lamp to decorate the room.
From very simple materials, such as cardboard, old glass, hand-sewn, cloth, and rope,
we have a very beautiful lamp to decorate the room.
As in the previous videos, I will also list the minutes of each step in the description section.
If you are in the middle of it, you can click on that minute to continue.
Every Sunday, my channel will have a new video to guide you how to make handmade stuff.
Decorate the house, recycling, gifts too.
So please click the subscribe button below.
And remember to ring the bell to receive my earliest videos every week.
I have an old glass jar that I used up.
Now I'm going to peel this off.
I will cut a piece of cardboard 28cm in size, 14cm in width.
This piece of cardboard is a bit thick, everyone.
And I cut it in half.
So we have 2 pieces, each piece is 14cm in diameter.
You can change the size of this piece of paper, depending on your jar, whether it's big or small.
The step to cut this circle hole is very difficult for me, everyone.
Partly because my knife is blunt, it's not sharp anymore.
And in the pandemic, I couldn't buy anything.
So I've made a circle hole.
I'm going to put my jar in and see if it fits.
OK, it fits.
Like this, everyone.
Now I'm going to cut a piece of cardboard to wrap around this canton beer, everyone.
And use a glue gun to stick it in.
And I'm going to cut 4 corners like this.
Cut 4 corners like this, everyone.
I ran out of glue gun, everyone.
And because of the pandemic, no one could deliver it.
Now I don't know what to do.
I don't have any glue left.
It's so sad, is there anyone in the same situation as me?
Then glue the edges together.
I try to save glue gun as much as possible.
I try to save a lot.
Every time I apply it, I only apply enough to make it stick.
This time I learned a lot, everyone.
Glue and other types of glue will never be missing.
And this step, everyone, just stick it close to the edges.
Then cut off the excess.
I spray glue on the edges, everyone.
Then press it down on the table so it doesn't get hot.
And we will have very square edges like this, everyone.
I will do the same with the other side.
So we will have a very square edge like this.
Next, we will stick the edge that we have drawn in a circle.
First, I will fold the piece of cardboard back to ensure that it covers the entire piece of cardboard.
Then I take a pen to mark the circle.
And cut it like this.
If you find this video useful, please press the like button below.
And don't forget to press the red subscribe button.
Press the bell to receive my earliest videos.
Now we just need to use glue to stick it back.
And remember to stick it around the edge of the circle.
So that it doesn't bulge.
And I will use the same technique as before.
Glue the glue and then tilt it to put it on the table.
To make it square, everyone.
Similarly to the previous hole, I will use a pen to mark and drill that hole.
Then we just need to use glue to stick it back tightly.
If you don't have glue with you, save a little bit.
I cut off the excess parts to stick this edge in, everyone.
In order for us to share with each other about DIY, handmade, about life.
Please like my fanpage.
I will put it in the description below.
I will cut a layer and leave a layer to stick it in.
Like this.
And cut off the excess.
Ta-da! And we have a very square and very beautiful piece, right everyone?
Yay!
Now I'm going to put the hole in.
OK!
Very good, everyone.
Now I will use a wooden stick to measure the size of the piece of cardboard.
And I took the handmade sticks to put on top.
At this time, I left it a little broken, it was not very beautiful, everyone.
So I will adjust it to make it stick in a little bit like this.
And use a glue gun to fix it.
In this pandemic season, we all stay at home a lot.
And I hope that with my DIY videos, you will have more suggestions to make home decorations.
And also make our day happier.
I have finished two pieces.
Now I will measure to put it in the right position at 2 meters like this.
And use a glue gun to stick it back.
A small trick is that you do like me.
I will put it in the right position that I want to stick.
Then I will put the glue gun in and lift it up.
Then it will definitely be in the right position.
I don't need to measure again, everyone.
And I will fix it with a lot of glue gun to make it firm.
This step is not savable, everyone.
I will continue to stick it on the other two sides.
To complete this.
This step I super save glue, everyone.
Stick very little glue.
Can you see it? My glue is gone.
Now I don't know how to buy glue, everyone.
I will decorate the flower inside a little bit.
I twist its tail like this.
And stick the glue in.
And stick inside.
Because my hole is a bit short, everyone.
So there is still a lot of empty space below.
So I decorated it with dried flowers.
And if you use holes that are long.
You don't need to decorate with dried flowers.
Now I will put the hole on top.
And use a glue gun to stick it back like this.
And I will use a large wire.
Put it on top of the hole.
Like this, everyone.
At this time, I really ran out of glue.
So I have to use fire to light the candle glue.
Stick it manually like this, everyone.
Because my glue gun can only use small candle glue.
But I still have 2 large candle glue.
So I have to use fire to make it hot.
Does anyone have the same situation as me?
Comment below for me to know.
And next I will make a wire for this lamp.
I will also use a large wire.
And after tying it up.
I will pull these wires to make it fresh.
To make it smooth and soft.
And decorate it, everyone.
Besides, doing this will make it difficult to come out.
Finally, we will put the light in.
Here I use a normal candle glue.
But if you use a small wire.
It will be much more beautiful.
But I only have this candle right now.
I will wrap it like this to make it neat.
And I will put the part with the most lights outside.
I hope you have more suggestions to decorate the room with lights.
In the near future, my channel will have more videos.
Instructions for decorating.
More interesting gifts.
If you press the button to subscribe.
And remember to press the bell button to receive my latest videos.
Goodbye, I wish you success.
