4 Trò Chơi Thú Vị Ở Nông Thôn Xưa

MangoVid
88 người theo dõi
105 Lượt xem video·8 thg 10, 2023
Hello everyone, there is a toy that is sold in front of the school that most men like very much.
It is a plane with a flat wing that can fly thanks to a rubber band.
This is the kind of plane I used to play when I was a kid.
The overall design is very beautiful and looks like a plane with a fan in the early 20th century.
This plane is designed with a light wooden body.
The end of the wooden body is connected to a small horizontal wing on both sides and a standing wing in the middle.
These wings have the function of stabilizing the plane when it is in motion.
In the middle, the body of the plane will be equipped with a large, long wing, which is designed slightly curved at the front and bulging at the bottom to increase air resistance to create momentum for the whole plane.
All of these wings are made of soft foam, but they are quite solid.
All of the wings of the plane are made of soft foam and are very easy to break, so it is necessary to avoid making it stiff when playing.
In front, the body of the plane is equipped with a fan, with the end of it connected to the rubber band under the wooden body.
When the rubber band is twisted, they will make a fan and pull the plane forward.
One important thing about the design of this plane is that when you put it on a thin horizontal bar, right at the position near the back of the large wing, the plane will be balanced and will not fall forward or backward.
Because this is an uncontrolled plane, the tail wing only has the function of keeping the plane in the right direction.
Raising the plane will be carried out by the entire front wing.
That's why you can see that they are designed to be balanced at that position.
Now we will rotate the fan for the rubber band to rotate.
Place the plane forward and not slightly.
You see it flies away very beautifully.
We will take them back and continue to play.
When playing with a balanced plane, you will notice that the plane always has the direction of flying to the left, but very few cases of flying to the right.
This is also explained by the opposite direction of the fan when rotating.
Because the fan is attached to the main axis of the plane, so when the fan rotates in this direction, the plane has the direction of rotating in the opposite direction.
Therefore, while flying, the fan rotates in the same direction, which creates a force that makes the plane tilt in the opposite direction.
The tilted plane combined with the momentum of the wing has made it fly around to the left as you can see.
After playing for a while, we will take the plane to cut.
Then look for the long-tailed dragonflies.
This is a type of dragonfly number 6, with a length of about 7cm.
Now we will insert a snail into the tail to get more power.
Remember to leave it about 1cm away from the tip.
At this time, cut out a piece of paper about 5cm wide,
wrap it around the dragonfly to make it into a rectangle, then cut off the excess part.
We will glue the edge on the outside,
while using a little hot glue inside to fix it to the dragonfly.
When the glue is dry, we get a long dragonfly body with a wing,
which helps the direction of the dragonfly to follow a certain direction.
Next, we will take a toy cannon,
cut them into small balls,
then insert them into the bottom of the dragonfly.
Remember to stick it tight so that when you press it down, the ball does not fall out.
Now you find a hard surface like cement or stone,
then drop the ball down.
When it falls, the ball will hit the surface and make a loud sound.
We can make a lot of dragonflies with cannons like that to play,
and when it falls, they will make a loud sound,
like the sound of a gunshot.
When I have played all the cannons,
I will put all the dragonflies in the box,
then go to the house to find a thin board.
Now we will cut the board,
take a piece with a length of about 4 inches,
then start from one corner,
we draw down 2 slightly slanted lines as you can see,
then cut along the drawn lines.
Next, I will sand the top and round the corners
to create a box-like shape like a gun barrel.
We will create 5 more frames above,
with distances of about 1cm,
then make a grid of pieces.
I will use another piece of wood,
close it to the back of the wood to replace the handle for the gun.
Now you take a piece of hard beer,
cut out a piece with a width of about 6cm,
then roll it into the body of the wooden body
at the position of the edges,
remember to create a slightly loose circle
so that the hard beer can be easily retracted.
I will use hot glue,
press the beer back and cut off the excess,
while cutting the heart at the top corner,
then put it back into the body of the gun.
All done,
we have a pretty nice gun with a barrel.
To play it, I will use a barrel,
shoot at the front of the dragonfly,
pull it back and hook it into the edges.
Remember to install the barrel at the front of the dragonfly,
then install it several times
to the dragonfly at the nearest position.
When you have loaded the bullet,
you just have to pull this piece up,
the hard paper will lift the barrel out of the dragonfly
and shoot forward.
We will use these wide barrels
to aim.
If you see the barrel gun is not very powerful,
we will use a piece of bamboo,
cut it flat,
then cut out a section with a length of about 13cm
and round off the corners.
These 4 sections look similar.
Now we will put 2 pieces of bamboo on top of each other
like a triangle,
then put another piece on top
with one end at the corner of a barrel
and the other end in the middle of the remaining barrel.
We will take a fourth piece,
stick it in the middle of this barrel,
put the barrel in the middle and cut it into the corner of the barrel here.
At this time, you narrow them down
and cut the barrel in half.
All done,
we have a self-combined structure
like a ninja butterfly.
We will break it into many pieces,
which looks very interesting.
