Basic Electronics For KTU students--Mobile communication -Hand off, Call processing,
Oct 6, 2023
Module 6
FOR FULL CLASS: https://www.youtube.com/playlist?list=PL2UV2EJdMQmjKsQm-dKy2Dr42PWiTzx4U
Let's see what is hand off or hand over.
Consider a situation, while we are travelling from place A to place B by car or bus.
Sometimes it happens for a short period of time.
The signal strength of our mobile becomes low.
And again it increases and reaches its normal level.
This is due to the hand off of a signal.
When someone travels from base station A, he receives the signal from base station A.
That is antenna A has a strong hold on this device.
But we move towards B, the antenna strength gradually decreases.
And when we reach the boundary of cell antenna A,
at the boundary, the hold of antenna A on the device is minimum.
At that time, our mobile device is entered into cell B.
Then base station B will start to take hold on the device.
Then at the border of cell A and cell B, both the antennas have equal amount of hold to the user.
When user X crosses the border and enters into cell B,
strength of base station A will very rapidly decreases.
And the strength of base station B will increase.
So the device gets the signal from base station B.
During this procedure, the call is still on.
So base station A hand over its call to base station B without affecting the call.
This is called the hand off procedure.
So the transfer of mobile from the control of one base station to the control of another base station is called hand off or hand over.
It occurs when mobile unit crosses the boundary of one cell and enters into another cell.
There are mainly two types of hand off, hard hand off and soft hand off.
So two types of hand off, hard hand off and soft hand off.
What is hard hand off?
So what is hard hand off?
It says that when a person is moving from one cell to another cell or one base station to another base station,
the previous connection will be broken and a new connection will establish.
So at that time, the first connection will break and a new connection will establish.
So break before make.
So at that time, the mobile will be connected to only one base station.
So there will be chances for code breaking.
So we can say hard hand off as break before make.
So in hard hand off, a new communication link or new cell B is established after breaking the current communication link or old cell A.
It needs a switching frequency or time slot.
Examples of hard communication techniques used in cellular communication are FTMA and TDMA and TDMA cellular system.
FTMA means frequency division multiple access and TDMA means time division multiple access.
That we will study in the coming semester.
Next is soft hand off or soft hand over.
So in soft hand off, a person moves from one cell to another cell.
So it will establish a connection to a new base station.
After that, it will break the old one.
So in soft hand off, link will break connection old cell only after making with new communication cell.
Example, in CDMA cellular system, we are using soft hand off technique.
So next is call processing.
Here we are discussing how we can make a call in mobile phone.
There are mainly three kinds of call processing methods.
First one, fixed to mobile.
Fixed network to mobile.
Here fixed network means our land phones.
So land phone to mobile.
Then mobile to land phone.
Then mobile to mobile.
These are the three types of call processing methods.
First of all, we are discussing about fixed network to mobile call processing.
In fixed network to mobile call processing, the switching center of a cellular system receives a call through the PSTN.
Public Switched Telephone Network.
So first, the switching center of a cellular system receives a call from our land phone.
Then that switch first determines whether the mobile phone unit is available or not.
If available, switch pages the mobile phone subscriber.
Following the page response from the mobile, the switch assign an ideal channel and instruct the mobile to tune to that channel.
At that time, an audible call tone is sent causing that mobile phone to ring.
This happens in a fixed network to mobile phone communication.
Next call processing method is mobile to a fixed network or mobile to land phone.
First, the mobile subscriber enters the land phone number using the keypad and then presses the send key.
That means that call button.
At that time, which transmits the called number and mobile subscriber's identity number to the switch.
If the called number is available, the switch routes the call over that PSTN.
So switch also assigns a channel and instruct the mobile subscriber to tune that channel.
Now an audible tone is available in the mobile unit.
When the called party picked up the phone, the switch terminates the call process.
At that time, the conversation can begin.
Next procedure is mobile to mobile communication.
When the call originates from a subscriber, the switch on receiving the caller identification number and the number called.
At that time, it determines whether the called unit is busy or available.
If it is free, the switch sends a page.
Then following a page response, the switcher assigns each party in an ideal channel and instructs each party to tune into their respective channel.
So for mobile to mobile communication, first the call is originated from a subscriber.
The subscriber has to dial that mobile phone number.
And that mobile phone number sends along with the caller's identification number.
And that determines whether the called unit is busy or available.
If free, the switch sends a page.
Following the page response, the switch assigns each party an ideal channel and instructs each party to tune their respective channel.
This is the procedure for mobile to mobile communication.
Here the figure shows the various components used, various blocks used for call processing.
The blocks are Public Switching Telephone Network, Mobile Telecommunication Switching Network, Mobile Telecommunication Switching Office, MTSO, and Base Transceiver.
Next is some terminologies used in mobile communication.
First one is Base Station.
What is Base Station?
Base Station is a fixed station in a cellular system.
And it is used for radio communication with mobile stations.
Base Station consists of radio channels transmitting and receiving antennas mounted on a tower.
They are located at the center on the edge of coverage region.
We saw that a cell, cell is the range that a tower can handle.
And Base Station is at the middle point of that cell.
We have already studied.
Next is Mobile Station.
Mobile Station means nothing. Our mobile phone is a mobile station.
That is, a station in a cellular system intended for use while motion at unspecified location is called a mobile station.
Next is Mobile Switching Center.
Mobile Switching Center which connects the cellular base station and the mobiles to Public Switching Telephone Network, PSTN.
It coordinates the routing calls.
A MSC is also called Mobile Telephone Switching Office, MTSO.
That is, we saw on that block diagram.
Next is Control Channel.
Control Channel is that radio channel for transmission of call setup, call request, call initiation and other control purposes.
Next is Forward Channel.
Radio channel is for the transmission of information from base station to mobile.
And Reverse Channel is radio channel for the transmission of information from the mobile to base station is called Reverse Channel.
Next is Transceiver.
Transceiver is a device that is capable of simultaneous transmitting and receiving of radio signal.
SIM, we all know about SIM, SIM card. SIM means Subscriber Identity Module.
Let's revise the list.
First is Handoff.
What is Handoff?
When we are travelling, let's say we are travelling in a car or a bus.
Handoff is the switching process from one tower to another tower.
Even if we are on the phone, sometimes switching happens without dropping the call.
Sometimes if the call is not arranged, the call will be cut.
Handoff is that process.
We call the range of a tower as Cell.
We call that tower as Base Station.
When a person is travelling, he was told about the coverage area of a base station.
Handoff is the process of going from that coverage area to another base station.
There are two types, Soft Handoff and Hard Handoff.
Next is the difference between Hard Handoff and Soft Handoff.
Hard Handoff is when the call is switched from one base station to another.
If the call is switched from the first base station to B,
the call will be terminated.
The connection with the base station A will be cut.
The connection with the base station B will start.
Hard Handoff is the example of both FDMA and TDMA.
Soft Handoff is when the connection is established with the base station before the connection is terminated.
Hard Handoff is when the connection is established with only one base station.
Soft Handoff is when the connection is established with two base stations.
Soft Handoff is CDM.
Next are the call processing methods.
There are three ways to make a call.
You can make a call from a land phone to a mobile phone,
or from a mobile phone to a land phone,
or from a mobile phone to a mobile phone.
These are the three call processing methods in mobile communication.
The first method is to make a call from a land phone to a mobile phone.
The second method is to make a call from a land phone to a mobile phone.
The third method is to make a call from a land phone to a mobile phone.
First, the switch checks whether the mobile unit is available or not.
If it is available, the switch will follow a page for the mobile subscriber.
When the response from the page is received,
the switch will assign an ideal channel to the mobile.
At that time, an audible call tone will be sent to the mobile.
At that time, the mobile phone will start ringing.
These are the call processing methods from a land phone to a mobile phone.
Next is how to make a call from a mobile phone to a land phone.
First, the land phone number will be entered in the mobile phone.
Then the call button will be pressed.
When the call button is pressed, the number of the subscriber will also be entered.
If the number is available, the switch will connect to the PSTN.
Similarly, the switch will assign a channel to the mobile.
At that time, an audible call tone will be sent to the mobile.
Similarly, the land phone will terminate the call.
At that time, the conversation will start.
Next, let's see how mobile-to-mobile communication works.
At that time, when a subscriber makes an original call,
the switch will receive the caller's identification number and the number at which we called.
Then the switch will determine whether the channel unit is busy or not.
If the caller is free, the switch will send a page.
After receiving the page's response, the switch will assign a channel to that party.
The party will be tuned to that channel and the call will be formed.
This is a basic block diagram of mobile communication.

