KTU BIOMEDICAL ENGINEERING || EC365 || MODULE 4 || LECT 20 || PACEMAKER
For the full video of this course : https://www.youtube.com/playlist?list=PL2UV2EJdMQmh3GlNha5gwN8IsIyjOKcGh
#ktubiomedical #biomedicalengineering #ktu
Hi all, today we are going to discuss about PACEMAKERS
In our normal pumping circuits,
if we take any pumping circuit,
it requires electrical potential
for its proper working.
So, what is needed for our heart?
This electrical potential is needed.
Like what?
Like a pump.
Like a pumping circuit.
So, this potential,
where does the heart get this potential from?
It is from the SA node.
The SA node is situated in the top right artery of the heart.
We had discussed this when we studied the structure of the heart.
Now, if the heart does not get these electric pulses,
the pumping ability of the heart becomes weak.
This condition is called heart block.
In this situation,
physicians use PACEMAKERS to stimulate the heart.
So, let us see what is PACEMAKER?
PACEMAKER is a device which uses electrical impulses
delivered by electrodes to maintain and regulate the heartbeat.
And the main aim of PACEMAKER is to monitor heart's rhythm.
So, PACEMAKER monitors the rhythm of the heart.
If anything goes wrong,
there will be short low voltage pulses in the heart's ventricles.
Next, let us see different pacing modes.
The first one is TRANSCUTANEOUS PACING or EXTERNAL PACING.
In this, two electrodes are placed in the chest of the patient
and the electric current is increased.
This is usually used for emergency purposes.
For long period of time application,
we do not use TRANSCUTANEOUS PACING or EXTERNAL PACING.
The second pacing mode is EPICARDIAL PACING or TEMPORARY PACING.
This method is commonly used in open heart surgery.
In this case, the electrodes are in contact with the outer wall of the ventricle.
The next method is TRANSVENOUS PACING.
This is an alternate method of TRANSCUTANEOUS or EXTERNAL PACING.
In this, the wire of the pacemaker is placed in the vein
and then passed into either right atrium or ventricle.
The pacing wire is then connected to an external pacemaker outside the body.
Next, fourth mode of pacing is PERMANENT PACING.
In this, TRANSVENOUS PACING is used.
The electrodes are placed in the heart chamber of the patient.
Transvenous placement
One or more than one electrodes are placed in the heart chamber
And here the pacemaker is a hermetically sealed device
consists of power supply, sense amplifier, computer logic for the pacemaker and the output circuitry
pacemaker is a hermetically sealed device
hermetically sealed means we are preventing the passage of air, oxygen or other gases
hermetically sealed means we are protecting
pacemaker is hermetically sealed
pacemaker consists of power supply, sense amplifier, computer logic for the pacemaker and the output circuitry
so these are the four modes of pacing
there are three types of permanent pacing
single chamber, dual chamber, rate responsive
in single chamber, one lead is placed in either atrium or ventricle
in dual chamber, one lead is placed in either atrium or ventricle
in two chambers of heart, one lead is placed in either atrium or ventricle
this is the rate responsive
rate responsive means it senses heart rate according to patient's physical activity
and automatically adjusts the pacing rate
rate responsive means it senses heart rate according to patient's physical activity
and automatically adjusts the pacing rate
so these are the three types of permanent pacing
now let's see the pacemaker's block diagram
these are the different blocks in the block diagram
let me explain all the blocks in the diagram
if you are not able to see all the blocks in the diagram, please skip this part
three blocks at the top and three blocks at the bottom
draw them like this, five blocks in the middle
draw the blocks like this
the three blocks at the top are easy to understand
reversion circuit, r-wave sensing circuit, refractory circuit
let's see the middle block
timing circuit, pulse width circuit, pace limit circuit
let's see the middle block
timing circuit, pulse width circuit, pace limit circuit
rate slowdown circuit, voltage monitor and controller, energy compensation or pulse duration controller
these are the blocks in the pacemaker
now let's see each block in detail
let's see the timing circuit first
the first one in the middle
timing circuit is used to determine the basic timing rate of the pulse generator
timing circuit is a combination of RC network and reference voltage switch
next is pulse width circuit
pulse width circuit is used to determine the pulse duration of the pulse
pulse width circuit is triggered by the output from the timing circuit
pulse width circuit is an RC circuit
pulse width circuit is triggered by the output from the timing circuit
next is pace limiting circuit
the function of pace limiting circuit is to limit pacing rate
maximum pacing rate is 120 pulses per minute
next is heart stimulator circuit
this is the output circuit
this is used to stimulate the heart
now let's see the function of heart stimulator circuit
this circuit provides a period of time following an output pulse or sensed R-Wave
next is R-Wave sensing circuit
this is used to sense the R-Wave
this is used to reset the oscillator when the pulse is not needed
next is return circuit
this is used to detect the R-Wave
if the R-Wave is not detected, the oscillator will generate the pulse at the preset rate
next is voltage monitor and controller
this is used to monitor the battery voltage
if the battery voltage is low, this will trigger the pulse duration controller
next is rate slowdown circuit
this is the rate slowdown circuit
this is a special circuit which slows down heart rate during certain conditions
these are the different blocks of a pacemaker
next is timing circuit
this determines the basic timing rate of the pulse generator
it consists of an RC network, reference voltage source, a combinator etc
next is pulse width circuit
the stimulating pulse duration is determined by pulse width circuit
it is triggered by the output from the timing circuit
the pulse width circuit is also an RC circuit as the timing circuit
the output of the pulse width circuit is fed into pace limiting circuit
next is pace limiting circuit
the function of pace limiting circuit is to limit the pacing rate
the maximum pacing rate usually selected as 120 pulses per minute
next is hertz simulator circuit
this is also called output circuit
since it provides the proper input pulses to stimulate the heart
and hence called hertz simulator circuit
next is refractory circuit
this circuit provides a period of time following an output pulse or sensed R wave
during this time the amplifier will not respond to outside signals
next is R wave sensing circuit
the function of R wave sensing circuit is to detect or sense a spontaneous R wave
and reset the oscillator when the pulse is not needed
next is reversion circuit or return circuit
it allows the amplifier to detect a spontaneous R wave
in the absence of R wave the circuit again allows the oscillator to generate pulses at its preset rate
next is voltage monitor and controller
this circuit continuously monitors the battery voltage
it has to be monitored regularly
if the battery voltage is decreased
it triggers the energy compensation and pulse duration controller circuit
next is energy compensation or pulse duration controller circuit
if the battery voltage is decreased
the energy compensation circuit increases the pulse duration
last one is rate slow down circuit
it is a special circuit which slows down the heart rate during certain conditions
the circuit slows down the rate by limiting the current to the basic timing network
so this is all about pacemaker
I hope everyone understood the topic of pacemaker
see you in the next session
thank you for watching
see you

