Making a Router Circle Jig With Material You Already Have

TightWadDIY
899 followers
11 Video Views·Feb 3, 2018
Cutting a perfect circle can be an intimidating task. Using a simple router jig can make the process very safe and easy. This video shows the process I use to cut perfect circles for my wood art business, BentonArt.
Welcome back, guys.
It's the Tightwad, and in this video, we're going to do something a little bit different.
We're going to start a woodworking series.
And I've made this.
I'll show you an example of the finished product of something that's similar to this, but this
is going to be a wooden round 36-inch circle, and a family name will go across the center.
This particular one will say the family name and then the date that they were married or
the year that they were married, so it will have the name established 2000 whatever.
So I'm going to show you today how I get from this, which is a rough cut piece of plywood
with pallet wood glued and brad nailed down to a beautiful 36-inch round circle.
So let's get started.
So the first thing we're going to talk about today is how I made, how I got to this point.
I rough cut with my jigsaw a approximately 38-inch round, and I measured out the round
by putting a hole, I drilled a hole right in the center, and put a nail inside with
a measuring tape or a yardstick.
In this case, I used a yardstick.
And I had a pencil at the other end of it for 38 inches or actually 19 inches from the
center.
And I, from the nail to the hole I drilled at 19 inches, I drew a circle, and then I
rough cut it with a jigsaw.
So that hole is key for the whole process.
Then I planed some pallet boards so that they'd have a nice smooth surface on the backside,
and I glued them down, so I laminated them to it with Titebond II and a couple of brad
nails as needed.
Since all the nails were removed from the holes, I actually shot brad nails into the
holes to hide most of them as much as I could, and most of my nail holes are in the middle
instead of on the outside.
If you don't decide to plane the boards and remove the nails, just make sure there are
none in the path that the router will hit.
So that's how we got to the point we are now.
The next step is to set up for cutting the circle.
So let me get the supplies I need, and I'll be right back.
Alright, so for this project, I'm actually going to be using a router to cut the circle,
and in order to cut completely through, I need to elevate the project.
So whatever I'm cutting, I have to elevate.
So I have some old scrap 2x4s and 2x6s, and then I can set the whole project face down
because my nail hole is in this side, and that will be used for the jig.
I'll make sure that none of my boards, my support boards, are in the cutting path, but
also that they are as far towards the edges as possible so they provide the greatest level
of support.
And then I will use quick clamps to hold it in place.
So I'll clamp it down on opposite ends.
Any kind of quick clamp will work for this.
It doesn't have to be a quick clamp even.
It can be a regular bar clamp such as this.
This is the version made by Bessie, which is a much higher quality clamp people claim,
but the quick clamps work great for this because I'm going to be releasing them.
I'll be releasing the quick clamps frequently as I make passes around my circle.
So the project is set up.
Now we have to worry about getting the router and router jigs set up.
So let's move on to that process now.
For the next part of the process, I'm going to be setting up my router.
I have an upcut spiral bit, and that is what I use to cut circles because I can easily
plunge into the piece and it clears the debris as it cuts.
So I will go ahead and get that installed in my router.
I just use the flathead screwdriver here to remove the screws in the base plate.
There are three screws in this particular model.
The next step is attaching the jig that I've made to my router, but let's talk about the
jig itself first.
It is simply a quarter inch piece of poplar board.
What I did is I matched up the holes on the base of my router where the screws are to
the board and drilled holes.
And then I also drilled a hole where the router bit will go through this board.
So the router's going to sit on top of this board and the router bit will go down through
this hole and into the project surface.
So the next step is to measure from the edge, the inside edge, which this is the center.
So this will be the inside edge of this hole to the point on the jig where you would like
to cut.
So you want the diameter of your project.
In this case, I'm cutting 36 inches.
So I have a hole right here in the center of my board and I've marked it 18 inches.
You see I have several holes here that I've used for different projects, but this is the
one that I'll be using today.
And the nail will go through the 18 inch hole and into the center hole for my project piece.
So I'm going to attach the jig to the router first, and then we'll attach the jig to the
project piece.
So now it's time to attach the jig to the router itself.
And I know this is the top, the bottom actually has some skid marks from where I've used this
several times.
And I will now attach it with some flathead beveled Phillips screws.
I like the flathead instead of the ones that come with the base plate for the router because
the ones that come with the router have a beveled head and they get in the way.
I don't have to recess these as much.
So I'll go ahead and screw these in.
Make sure you get all three in.
They don't have to be super tight, but make sure they're tight enough that they're not
going to vibrate out.
All right, so the jig is firmly secured to the router and now I can flip this upside
down or right side up.
And I'm going to take my nail and go through my 18 inch hole in my jig and put it dead
into the center hole that I pre-drilled when I was first marking out the pattern on my
project.
Since I know I have about a half inch of pallet wood on the other side, I will hammer the
nail in just a little bit to hold it securely in place.
It doesn't have to go all the way down.
One tip that I learned from doing this is the cord always gets in the way for the router.
So what I've done is I suspended a hook from my ceiling or screwed a hook into one of the
floor joists of my ceiling.
And I then plug in the router so that the cord always stays elevated over the router
and I don't have to worry about it getting in the way.
So I'll pull the slack out of this cord and get it out of our way so that we can see what
we're doing and we will go ahead and get started.
So now you can see that my cord is out of the way.
It has free range of motion to spin all the way around as many times as it want.
And then the final step is to wear your safety equipment.
So I'm going to remove my hat.
I'm going to put on my mask.
This is a 3M mask.
I'm not affiliated with any companies, but I've really found things that I like.
This is a 3M mask and this one's rated for dust.
With these filters, it can also be rated for chemical with the cartridge pink filter.
So I'm going to put this on.
These are the uvex goggles.
I like these better.
I had the Dewalt ones as well that are made similar to these, but these have a lot softer
flex in the piece that goes around your eyes and your nose.
A lot more comfortable and actually seal better.
And then I have the 3M work tunes.
These are good.
I found them at Walmart on a great deal for about 30 or $40.
I don't remember the cost.
For over the ear pieces, these are some of the best that I've most comfortable I've found.
They have a super long charge life and they also connect to your phone through Bluetooth.
I'm not going to be using that today, but I will go ahead and put on my safety gear
and we will get started.
All right.
So the process is to plunge down a little bit at a time.
About a quarter inch with this bit seems to be the magic number.
If you plunge all the way through at once, the threads on this actually aren't deep enough,
but it would also put a lot of strain on the bit and possibly break it.
So we're going to go a quarter inch at a time.
So the process, I'm going to do a dry fire here.
I'll plunge the router down.
I will lock it into place using the locking mechanism and slowly work my way around the
entire piece.
When I get back to the same spot, I will adjust my depth adjustment right here and it will
incrementally go down until we've cut the whole thing.
So let's get started.
This section of the video is sped up to be four times the original speed, so don't let
it fool you.
I go relatively slow on the first pass to make sure the groove gets cut accurately and
correctly.
You also see that I take my vacuum cleaner and clean up all the dust and check the groove
to make sure that it's exactly where I want it to be.
So now I will release my router to raise the bit, adjust my depth adjustment here, lock
it into place so it does another increment down, and I'll make another pass.
You saw that I've added a weight here.
That's to keep the back end of the jig from raising up to make my cuts inaccurate.
It's going to keep it from riding up on the nail with that just riding smoothly on the
other end.
This section of the video is actually sped up eight times the normal speed.
I just wanted you to see how many passes it took me to cut through.
I took four total passes and then a fifth clean up pass because I didn't quite have
it adjusted for some of the thicker boards.
So you'll see that I make my four passes and then I take the jigsaw to cut in from the
side to remove the circle.
I could just release the clamps and lift the whole thing up if I had made a clean cut through
on the fourth pass.
If on your fourth pass your board starts to sag a little bit, you can put some braces.
Since I used 2x4s under, I could grab another cut off of a 2x4 and stick it under the edge
to keep it from sagging and binding on the router bit as I go around.
So it's actually good that I didn't quite cut through on the fourth pass.
You can see here I'm removing all the pieces and there are a couple of boards in this section
right there where they didn't go all the way through and I just snapped them off.
They were so close to being cut through and then I made one last pass to clean everything
up right here.
So you see that once we're done we have a perfectly round circle.
There's a little bit of splintering on the edge but my second to last pass I guess wasn't
quite deep enough and it left some splintering on some of the wider or thicker boards.
But now I'll take a sander and lightly sand down the whole top to get rid of some of the
roughness of the natural pallet wood.
Always wait until I'm already done cutting and then I'll sand a little more on the edges
to get rid of all the splintering and then it's ready to apply the name.
So I hope you guys learned something.
If you have any tips or tricks that I should add to my arsenal for cutting these circles,
leave it in the comment section below please.
Anything to make it safer or easier, I'm always a fan of learning.
So newer to woodworking, I've been doing it for about two and a half years so I'd love
for more experienced people to give me tips as we go and let's learn together.
Thank you guys and hope you have a great day.
This is an example of what I'm doing with my wood rounds.
You see that I have the last name Boyle and then established in 2009.
Those are scrolled out of MDF and spray painted and then attached with wood glue to the center
part of the circle.
If you like this and wish to place an order, you can check me out on Facebook or Instagram
at BentonArt to see some of the other things I've made.
If you like this video, give me a thumbs up, subscribe to my channel and post any questions
or comments you may have down below and I hope you guys have a great day.
