TRANSISTOR BIASING - INTRODUCTION || ECT202 ANALOG CIRCUITS || EC205 || ECT 281 ELECTRONIC CIRCUITS
This video contains Need for biasing, operating point, concept of DC load line, Stability factors
This topic is also in the syllabus for
1. ECT202 ANALOG CIRCUITS:https://youtube.com/playlist?list=PL2UV2EJdMQmhbgPiP-dnVeRNTF0Pcfmpk
2. EC205 Electronic Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmiePALNs84TJUONtzApG9pp
3. CS 207 Electronic Devices and Circuits: https://youtube.com/playlist?list=PL2UV2EJdMQmh9Royg7s7B78IiWpou-lE0
4.ECT 281 Electronic Circuits ( Minor): https://youtube.com/playlist?list=PL2UV2EJdMQmiduKsGRgNFuu_MqB__HVpN
#circuits #ktu #ece #electroniccircuits
Hi all, today we are discussing about biasing in BJT
The last topic in the first module is biasing
What is biasing? Why we are using biasing?
What are the needs for biasing?
We are going to discuss all these today
So, what do you mean by biasing?
What is biasing?
Biasing is to operate a transistor in its required region
We are providing biasing
Biasing ensures that the device operates in a required region of operation
and also stabilizes the circuit against external variation
Why do we use biasing?
Biasing ensures that the device operates in a required region
and also stabilizes the circuit against external variation
That is why we are providing biasing
Now, let us consider the biasing of a transistor
What are the regions of operation of a transistor?
There are 4 regions of operation of a transistor
Active region, active region, cut-off region, saturation region, and inversion region
Active region is the region in which the transistor operates
Linear region is the region in which the transistor operates
The activity region is also called linear region
The second region is cut-off region
Both are reverse biased
In this way, we can operate transistors in different regions of operation, we can operate
transistors in different regions.
Why do we need to operate transistors in different regions of operation?
We can operate transistors in different regions of operation.
We must fix the operating point
in the region that says we should fix it.
That is the need of biasing.
This next problem is DC Load Line or Q point.
I am considering a fixed biased circuit.
Fixed bias circuit has a constant voltage coming to the base of the transistor.
Vcc is the voltage coming to the base of the transistor through a resistor called RB.
This is called a fixed bias circuit.
Let us plot the output characteristics of a transistor to draw the DC load line.
The output characteristics of a transistor is the relation between the output voltage and the output current.
The output is taken from the collector and the ground is connected to the ground.
This is how we take the output.
This is the output.
The output is taken from the collector and the ground.
This point is the emitter.
This is VCE.
What is the output current?
It is the collector current.
This collector current is the relation between the IC and the VCE.
It is called the output characteristics.
We have studied this in the first year.
If you take the output characteristics of a transistor,
we can draw like this.
We have studied that if we take the output characteristics of a transistor,
we will get something like this.
This is the region.
This is the cut-off region.
This is the active region.
This is the saturation region.
The region below the cut-off region is called the inversion region.
This is how we mark the different regions.
Active region, saturation region, cut-off region and inversion region.
The different regions we operate the transistor.
Active region, cut-off region, inversion region, saturation region.
We can fix the cut-off region or saturation region wherever we want.
If we want to operate the transistor as a switch or an amplifier,
we have to fix the active region.
To fix the transistor in these regions,
we have to draw a line.
That is the DC load line.
Let us see how to draw the DC load line in this.
I am taking the output characteristics.
In the output characteristics, we are going to draw the DC load line.
Let us draw the output equation for the output characteristics.
The output will be taken from here.
The Vout will be taken from here.
Otherwise, Vout is the same as Vc.
If we apply KVL on the output side,
the total voltage is Vcc.
The voltage from here to here is Vcc.
The total voltage is Vcc.
The total voltage Vcc is equal to the total voltage Vcc.
That is the total Vcc.
We apply KVL on the output loop.
That is the output loop.
The total voltage Vcc is equal to the total voltage Vcc.
is equal to Vcc is equal to Icrc plus Vce, total voltage Vcc is equal to Ic into Rc plus
Vce.
Vce is equal to Icrc plus Vce into Rc plus Vce is equal to Icrc plus Vce into Rc plus
Vce.
In this example, we are going to find out what is the X value and what is the Y value
in the graph.
In this example, we are going to find out what is the X value and what is the Y value
in the graph.
In this example, we are going to find out what is the X value and what is the Y value.
In this example, we are going to find out what is the Y value and what is the Y value
in the graph.
In this example, we are going to find out what is the Y value and what is the Y value
in the graph.
In this example, we are going to find out what is the Y value and what is the Y value
in the graph.
in the table here.
Find the point on the y-axis. To find the point on the y-axis, we need to zero the x-axis.
To zero the x-axis, we need to zero the vce.
When we zero the vce equation, we get vcc is equal to icrc.
From this we get, ic is equal to vcc by rc.
y-axis point is Vcc by Rc
we get two points here
y-axis point is Vcc by Rc
and x-axis point is Vcc
we can draw a straight line
connecting these two points
we can draw a straight line
this straight line is called
DC load line
this is called DC load line
if we want to work as an amplifier
the Q point should be here
in the active region
the middle point of the DC load line
is the active region
is the middle point of the DC load line
if we want to operate a transistor
is the middle point of the DC load line
we can fix the Q point at the exact middle point
of the AC load line
and use it as an amplifier
the output equation is given
we have to search for IC and VC
y-axis and x-axis should be 0
Vcc should be equal to Vcc
Ic is equal to Vcc by Rc . These two points can be joined together to form a straight
line known as DC load line and we can fix the Q point . We can fix the operating point
on DC load line . If the load resistance is infinity we must keep the operating point
at the center of DC load line to get maximum output sink . Otherwise Q point may be fixed
depending on the output sink requirement , load requirement , gain requirement , frequency
response , supply voltage , distortion allowable , noise figure . We can fix the Q point on
DC load line depending on the output sink , load requirement , gain requirement , frequency
response . We can fix the Q point on DC load line depending on the output sink , load
requirement , gain requirement , frequency response .
It should remain constant irrespective of internal or external variation . It should
remain constant irrespective of internal or external variation .
Any variation in Q point may deviate from its designed region of operation and to distort
output waveform . Any variation in Q point may deviate from its designed region of operation
and to distort output waveform . Variations in temperature fluctuations in power supply
, aging of components and replacement of active elements as BJT , FET etc . These are the
main parameters responsible for variations in Q point .
The next important parameter is stabilization factor . Stabilization factor is a change in
We said that the temperature change, power supply change, aging of component, active element replacement will be due to the Q-point variation.
What we consider the most is that the temperature changes should not affect the circuit.
Because the power supply variation can affect the circuit.
Power supply is provided by institutions like KCB.
There can be a variation in the voltage.
Also, the components we buy can age.
That can happen.
Also, if an active element is damaged, it can be replaced.
Temperature is a parameter that can cause variation.
So, we have to consider, highly consider, that temperature won't affect our equipment or our circuit.
Temperature variations should not affect the circuit.
Let's see how temperature variations affect the stability of the circuit.
Due to temperature changes, there will be variations in various parameters of the transistor.
For example, ICO is the leakage current.
Beta is the gain of the transistor.
VBE is the variation of these three parameters.
The change in temperature causes ICO, Beta and VBE of the transistor to change.
Let's see how each parameter changes.
First, ICO.
ICO is doubled.
It is 2 times ICO.
When?
For every 10 degree rise in temperature.
ICO is doubled.
Next, VBE.
VBE is the base emitter voltage of a transistor.
Base emitter voltage is reduced by 2.5 millivolts for every degree rise.
VBE reduces.
VBE is reduced by 2.5 millivolts for every degree rise in temperature.
For example, if the transistor is biased at 0.7 volts,
VBE reduces by 0.7 volts minus 2.5 millivolts for every degree rise in temperature.
VBE is reduced by 0.7 volts minus 2.5 millivolts for every degree rise in temperature.
Due to the variation of these two parameters, there will be variations in Beta.
Beta is the current gain.
In the case of common emitter, Beta is the current gain.
Beta will also vary with temperature.
Due to the variation of temperature, there will be variations in Beta.
Stabilization is the stabilization of collector current against temperature variation.
Stabilization of collector current against temperature variation.
The variation of collector current with variations in these transistor parameters are expressed by different stabilization factors.
The first one is the stability factor, denoted by S. The second one is the variation of the
collector current, denoted by Ic. The third one is the stability factor, denoted by Vb.
The fourth one is the stability factor, denoted by Vc. The fifth one is the stability factor,
denoted by Vc. The sixth one is the stability factor, denoted by Vc. The seventh one is
the variation of the collector current, denoted by Ic.
S dash is equal to dou Ic divided by dou Ic divided by dou Ic.
S dash is equal to dou Ic divided by dou Vb.
That we will discuss in next class. So today, we are discussed about biasing the BJT.
What do you mean by biasing? Biasing is used to operate devices in a required region of operation.
Also, it will stabilize the circuit against external variation.
In a transistor, in different regions of operation we will discuss active region, cut-off region,
Cut-off region, saturation region and inversion region.
To work as an amplifier, it will operate in linear region or active region.
To work as a switch, it will operate in saturation or cut-off region.
Next, we learned about the DC load line and Q-point.
To find the DC load line, we drew the output characteristics of the output transistor.
In that, we took a fixed bias and applied KVL in the output loop.
In the equation of KVL, we found the parameters of X-axis and Y-axis.
We got a straight line. That straight line is called DC load line.
We drew the DC load line and found the Q-point.
To fix the Q-point, we learned about the variations of the Q-point.
We learned about the temperature variation, power supply variation,
gauging of components, replacement of active elements.
We learned about the variations of the Q-point.
Next, we learned about the stabilization factors.
What are the different stabilization factors?
The temperature changes the variation of the collector current.
The temperature changes the variation of the parameters of the transistor.
We learned about the variation of the collector current.
We learned about the variation of the total collector current.
That's all for today.
In the next class, we will learn about the different biasing techniques of BJT.
Hope everyone understood.
See you in the next class.

