Toyota 2007-2013 Model Door Panel Removal Instructions

TightWadDIY
899 followers
Jun 29, 2019
There are many reasons a vehicle owner may want to remove their door panel. I removed mine to replace the door lock actuator but you may also need to work on the window motor or replace your speakers. This video shows the step by step process for removing the door panel without breaking anything. These same concepts apply to most vehicles but they specific truck used in this video is a 2007 Toyota Tundra.
Order Parts:
Door Clips - https://amzn.to/2ZXYz8M
Trim Tool Kit - https://amzn.to/2IYd3j5
Door Lock Actuators - https://www.ebay.com/str/Actuators-Plus
Screw Drivers - https://amzn.to/2Xi2PD9
Welcome back guys it's the Tightwad and this video is going to show you how to
remove the door panel on a 2007 to 2013 Toyota Tundra. If you have any questions
make sure you post them in the comment section below and I will answer them as
quickly as possible. There is a little plastic cover that you remove from here
and then there's a little padding in here that you remove. I need a Phillips
head screwdriver to remove the screw inside here and I'll set this to the
side and then I need to remove a Phillips head screw right here as well.
And that's the only two screws holding this panel on. There's also a bunch of
clips but that's the only two screws. So you do need your window to stay up
during this process because you're gonna be working down behind it. And the next
thing before you start removing the door trim you need to remove this part as
well. So this part you can sometimes get your fingers in here and just pop it
off. It's just got clips in it and I just lift it up right here and it popped off
and then there's a clip on the front I want to kind of be careful with so I'm
gonna wiggle it just a little bit and it exposes the back here. So this one has a
push tab right here that I can push in with my finger and wiggle out and this
one has a push tab right here on the front as well that I'll push down and
it'll come out. So I'll just set this piece right here to the side. The first
piece of trim I'm gonna remove is this little triangle right here. It is just
held on with clips so you can just get your fingers under it and pull it off.
It's actually just this one white clip here. You'll see a bunch of these today
and then a little tension clip right here as well. The next thing I have to
remove is this little clip right here. It's the only one made this way but you
take your tip of a screwdriver or something sharp and push in on it a
little bit to release it and then you can pull it out with your fingers or a
flathead screwdriver but I actually have a trim tool that I purchased. It's a good
idea to have for this process and that helps pull it out. So you can see the
button just pushed down into it and then it popped out. If you try to pry this off
you're just gonna break it every time. And with those two things done on this
door I can start at the bottom and start popping off all of the clips that
go all the way around. You can kind of do it by feel. Some of them may break but
they're easy to buy new ones and replace them. And this whole piece is just
resting on the arm up here at the top. So I'm gonna just start here at the
bottom where I can get my fingers in and start pulling. You can kind of hear
things popping free. Now with everything released, the top, the bottom, and all the
clips released, I can lift up here. So with this off there you got to support
it because there's a few things you have to unhook in the backside here. The
first one is down here at the bottom and I'll show you after I get it unclipped.
Up here at the top you have your two actuator cables. They go into your locks
and they both pop off by lifting up and then just releasing the balls. And then
the same thing with the bottom one. Mine was white on top, green on bottom. That's
important to remember. So the cable I removed from the bottom is just a little
clip that goes in this light cylinder right here and it has a little pressure
clip. So I pushed in the pressure clip and slid it right out. The actuator clips
went here and here. So this one just simply popped out of this slot here and
then slid out of this groove right here. And then the other one pops in here and
slides into this groove. So this is clear to be set to the side for the rest
of the process. One more thing is you'll notice that some of my clips are stuck
in here. So I'm going to take my trim tool and pop these clips out because
these are actually supposed to be in the door panel instead of in the door itself.
And I see one there and one over here. So when I look at the door panel I can see
there was one that was supposed to be here so I can slide it back into place.
And then another one was supposed to be here so I'll slide it back into place
also. These can be very fragile. You can buy replacements fairly easily at an
automotive store, at your dealership, or even on eBay and bags of about a hundred
of them or Amazon. So I'm going to start reassembling the door. The first step is
I'm going to hang it on the top up here so that I can get this bottom clip put
in place for the light. And you'll know it's done correctly when the light comes
on. And now I can pull this back off. While supporting it with my knee I'm
going to reconnect my cables. And my white one was on top and the green one
was on the bottom. If your vapor barrier pulls away make sure you smooth it
back down. Then I'm going to get it resting on the door here. So now it's
time to reinstall this piece here. And you have to fish your cable ends out. And
the big one goes on the main assembly. Small one goes on the other. You can't
really do them backwards. And I'm not going to secure that yet until I get the
door pushed back into place. So I'm going to make sure that it's settled on the
top here. And then I should just be able to push all the clips back into place
with a little shove. And now I can snap this back down. Before I go any farther
and put any screws in I'm going to test my lock and unlock functions. And you can
see that everything is functioning properly. Alright now that I know that
everything is working properly I'm going to put my two screws back in here. So my
silver one went up here by the door handle. And then the black one went down
in here. Put my little piece of padding back down in here. I need to reinstall
this plate here. It just snaps into place. I can go ahead and install this one
making sure the yellow lines up with the tab right here. And it should clip into
place. And then I have this pressure sensitive screw here. I'm going to push
it up a little bit. And I'm going to pop it into place. And then the tab pushes
down flush. So you can see it should not be pushed in. If it's pushed in it's
going to fall back out. So it just pushes flush with it. I hope you found this
video helpful. If you did give me a thumbs up and subscribe to my channel. I
have several other videos for this truck posted. If you want to order any supplies
for this process check the description for the video and you'll find some links
to Amazon from there. Using these links doesn't cost you anything extra but it
does help me out as they're affiliate links. If you have any questions post them
in the comment section below and I'll reply as soon as possible. And I hope you
guys have a great day!
