50 | Tự Học Cắt May | Cách Cắt May Quần Baggy - Alibaba Phần 2 | PHÁT TRIỂN MẪU VIỆT HIÊN

Welcome everyone back to the Viet Hien Sample Development Channel Then today I'll show you the next part of the tutorial on Petri clouds Alibaba Then the video link for part 1 the front part I will put below the description or below the video comments After tying our front part looks like this And now I'll move on to the rear design part First I will tell a story that goes like this And then I will measure from the center front line to the edge of the cloud line on the back side Then here we measured it as 17.5 cm Then from the line that I just measured I will take it as 17.5 cm This bottom part is also 17.5 cm And then I will connect the two points of movement Then this road will be the main middle road of the back body Now I will take the front body I look good with two straight lines together And I will mark the horizontal lines : waist hip base gusset and crotch I will mark the horizontal points of the front body For the inner side we will mark the horizontal point of the package and the horizontal point of the blend On the side where we sit we will take the horizontal lines of the waist the hip the base the chest and the back And we will move the front part of the base to the back part Now I will take out the front body and reconnect the horizontal lines During the time you watch the video Then the likes and comments you leave on your channel are very valuable contributions from you And it's the motivation for me to create more good and high-quality videos From these points we will calculate 1 cm on the left 1 cm on the package 1 cm on the bottom we hope you will calculate it as 2 cm And the distance from the back will be 4.5 cm Then I will connect the points again From this point I will take it as 1 cm Then I will reattach the bone as follows I will smooth out the bone line The inner edge of the package will be cut out by 1cm The middle of the package will be cut out by 1cm Then I will connect the two points of travel From the front body'scook line we will take out 10 cm and subtract 1 cm My waist size is 94cm From this point I will take 1.5 cm as the seam allowance And I connect to the package point From the edge to the middle it will be 1.2 cm And I will sign a section like this From the center of the back measure out 2.5 cm And I will sign a section Then I will place the thread at the corner into the horizontal lines Once done it's the central main line of the body I will mark a point here And from this point I will take 5 cm And from this 5cm point I will connect to the bone point And from this point I will connect down to the base point The horizontal lines are long And I will connect the two points of movement This straight line I will divide in half and connect it inside Continue we divide this line segment into two parts Then we bend the sole This section is curved inward by 1 cm from the straight line Next I will add 1 5cm of cloud fabric to the back My back is a separate piece Add 1.5 cm of seam allowance for the top edge to make it easier to sew And the seam allowance for the bottom edge is 1 cm Then the video link part 1 The front part I will put under the description Or under the comments The inner part of the body adds 1.5 cm of cloud-like pattern The cloud road seat is 1.5 cm Let's add 1.5 cm of cloud sugar Deep human 2 And now I'll move on to the back design First you'll draw a straight line like this And from this straight line I will drive down 8 cm This is the shape of the pants' back Now I will measure the waist On the table Deep and front body It is 56.5 cm I measured this as the finished product I haven't calculated the cloud pattern yet Then this back width will be 56.5 cm And I will draw a straight line right down the middle of this It's the fold line And I'll add some cloud sugar Surrounded by 1 5cm Thank you all for watching the video See you again in the next video Remember to like share and subscribe to the channel to follow new videos