19th Century Half Leather Library Binding Part 4 of 4 // Adventures in Bookbinding

Sparky Deal
161 followers
24 Video Views·Jul 3, 2023
Today, we're going to finish the half leather library binding.
Last week, we left off having done the corners, and today we're going to pick up at the spine.
This book doesn't have headbands or end bands, either machine made and stuck on or sewn on.
Instead, we're going to insert some cord into the turn ins at the head and tail of the spine and form a nice
head cap.
The square of this book is 3 millimetres, the square being the distance the boards protrude past the text block.
The leather's a bit under a millimetre thick, so I'm using a cotton cord that's about 2 millimetres thick.
So that will fill in the distance or equivalent of the square.
So I've just cut two pieces to fit along the top of the spine.
So we'll put the leather on the spine now, and we'll do the usual thing of moistening the outside of the leather.
It was extremely hot the day I did this and very dry as well, so I was really struggling just to keep the leather
moist. We'll give the leather one coat of paste, and then we'll let that paste soak in for a while.
And I'll go do it, get my tools ready for later jobs.
While that soaks in, I'll face it while it's soaking in so that it doesn't dry out.
Facing being folding the leather over on itself, but without forming a crease.
I don't want to crease the leather.
I just want to stop, reduce the evaporation and stop the paste from drying or setting.
Whenever the leather starts to dry out, I'll just give it a bit of a light sponge.
I'll prepare the cord for the head caps by giving them a thorough soaking in paste.
While using paste and keeping the leather moist gives me plenty of time to work, I don't want to muck around too much.
So I'm going to get my tools ready.
A couple of 4 millimeter knitting needles, my sharpened bone folder for pushing the turn ends in, a piece of cord
with a slipknot for setting the head caps, my bone folder that's really quite rounded for pushing in the joint.
So I've got everything ready.
So we'll put the leather on the spine now.
We'll give it another paste out.
I'll also paste up the spine of the book and onto the boards a little bit.
Make sure I get some paste down into the joint, but only where the the tab is that goes into the split board.
I don't want to get the paste down onto the inside of the book like I did just then.
Now, when I'm positioning the book on the spine leather, I normally put my head right over the top to make sure that I've got
the turn ends even at the head and the tail and the right amount of leather on either side of the book.
It was a bit hard to do because of the where the camera is, but I got it reasonably close.
I think I got a little bit more leather at one end of the book than the other.
But that's not the end of the world.
Once that's in position, you can flip it over and then pull the leather down onto the side of the book.
Always being careful not to dig your fingernails in and to pull it evenly.
Now, push the leather down with the rather wide bone folder into the joint.
The leather will continue to move around a little bit as we're working.
It'll come off the line a bit.
And that's fine because it's paste.
We've got plenty of time to make small adjustments later.
But we want to get the turn ends done and everything in its final configuration before we start making any final small
adjustments. So we'll start by doing one of the turn ends.
Now, I normally work on the edge of the bench.
So this board is just to simulate the edge of the bench.
So we'll put that cord in at the head cap.
Now, the hardest part I find is to stop pushing that cord down into the spine.
Once that's in position, we'll turn the leather over a little bit.
We'll just hook it underneath the top of the spine, just enough so that it stays there.
And then we'll put some paste in on that side of the leather that doesn't have any paste in on it at the moment.
There is paste on the spine, but we want to make sure that there's sufficient paste for that to stick to the spine.
So we'll add some extra now.
And once that's done, we'll push that over the piece of cord and then down under the spine.
And then we'll start to bring the turn ends over the boards as well and push those down into that gap that we left
between the boards and the tab that was inserted into the split boards.
Soon realize that the cord has gone too down, too far down the spine.
And that's fine. So we can just turn the, pull the turn in back out and start again.
We've got plenty of time to do this and get it right.
I'll just put a bit more paste on it because it's starting to dry out.
And I'll use the bone folder to push that leather down.
The only thing with doing that is you will push the paste off the leather as well.
So if you do that, then you might want to go back and add a little bit of paste.
But once you're happy with it, spin the book around and do the other end exactly the same.
Now, I'm very sorry about the soft focus that's going to come up for a while.
I just assume it was the heat.
I don't know why the camera was playing up this day, but I know the heat was definitely getting to me.
So I'm not surprised that the camera was a bit unhappy as well.
Now, before I form the head caps, I want to make sure the leather's pretty much in its final position on the spine.
And to be sure of that, I want to force the leather down into the joint.
So I'm just going to nip the book sort of gently, but firmly at the same time with the knitting needles, the 4 millimeter
knitting needles in the joints.
So I'm just going to put that in the press for about 5 minutes.
I'm going to do it for 5 minutes.
I don't want to leave it too long because I don't want the head caps to dry out.
So once the joint, the leather is in the joint well, I'll put the piece of cord around the book in the spine
groove. And I'll pull that reasonably tight because I want it to hold the leather in at the head and the tail when I
tease out the head cap.
Johnson suggests two shapes for the head cap, and I'm going to go for the one on the right.
So that sort of slopes into the book.
So I'll start by pulling the leather outwards to pull the cord down onto the text block.
And so once the leather is pulled out to the sides, then I'll start to shape the head cap.
Once you're happy with the head cap, flip it over and do the other end.
In the hot weather, I normally have a fan going and I normally turn it off when I'm filming.
But I forgot to turn it off while I was doing the head cap, so that's the background noise.
I've tried to turn it down without getting rid of the background noise completely.
But that harm is the fan in the background.
Once you've formed the head caps, then take the cord off.
And then I like to just give it one last press with the knitting needles in place, just to make sure that the
joint grooves are nicely set.
I'm only going to do this for about 5 minutes.
Put fences or barrier sheets in between the boards and the text block.
So after 5 minutes, I'll take the bricks and the boards off and then I'll just put the book on the edge of the
board and then let it dry overnight.
OK, now we have an option of filling in the side panel.
So I've just got a piece of manila card there and I've put it in and tested to see if what that feels like.
So Johnson shows this in example 2 here.
He actually pairs the edge of the card to go over the leather.
I don't go to that extent, but I do like filling in the sides.
So I'm going to do that.
And that also means that if the leather was a little bit uneven in that maybe it extended a little bit further on
one side of the book than the other, I can adjust that by just having the cloth go over the one side more than the
other. And if I've filled in the boards, then you won't notice it.
If I don't fill in the boards, I need to trim the leather up.
So I just like filling in the boards.
I think it looks nice.
And it also means that a lot of the wear goes onto the cloth rather than the leather, if the book's going to go in and
out of the shelves a lot.
So I, to cut the manila to the right size, I flipped it over onto a couple of boards and used my knife to mark it.
I cut it out to the size, the height and the width, and then I made a slight adjustment here.
And then I will transfer the corners and then cut the corners off.
It wouldn't be the first time that I've cut too much material off on the corners, but that's OK.
Then I just have a really good template to get it right on my second try.
And because I'm about to cover up my front and back marks, I'll transfer those marks to the manila card.
Now, if the leather at the spine or on the corners isn't really straight, you can make small adjustments.
Just trim the leather where it's sticking out a little bit.
Hopefully it's not too much.
If it's a lot, then you want to trim it at a bit of a bevel so that it matches the bevel on the pairing.
Now, from experience, I know that using this manila card with PVA means that I'm going to have almost no stretch.
That's something you probably want to test for yourself with your materials and your adhesive.
And if you do have a bit of stretch, then you want to trim the card accordingly to just give a maybe a half millimeter gap.
I couldn't imagine a card stretching too much.
Now, if you make a small mistake, like the card extends past the board, you can just trim it.
And if it's a little bit short, that's fine, too, because we're going to ease the corners with a little bit of sandpaper.
And if it was a fraction of a millimeter short, then that rounding over of the edge with the sandpaper is probably going to
hide that as well.
So I just use a piece of sandpaper to take the very hard corner off the edge of the boards.
Now I'm going to mark how much I want the board cloth to overlap the leather.
Now, I want that overlap to be about 3 millimeters or an eighth of an inch, but I want the corners to look nice and even.
So I've worked out how far that is in from the corners, which is about 60 millimeters.
So I'm going to mark that all the way around 60 millimeters in from the corners.
And then for the spine, I'm going to work out where I want it.
And then I'm going to mark that in from the joint groove.
Now, it's not perfectly vertical or parallel.
So at a couple of points, it's about 2 millimeters, but generally it's about 3 millimeters.
And I'm going to put that cloth so that it just covers those little marks, though they usually swell and disappear
anyway. I'm just measuring the side size of the cloth for the to cover the boards.
And I'll cut two pieces of cloth to size.
I'm using 20 millimeter turn ins, the same as I used for the leather.
And I like to crease the one turn in as my starting reference line.
So I'll put that turn in crease right on the edge of the book, and then I'll position the cloth along the spine.
I always like to put little pencil marks on my cloth.
Just I just like to have redundancy in my reference marks.
And then I'll fold the corners over to the prick marks in the leather.
Something I forgot to do was to break the cloth over the edges of the boards at the fore edge and the other end.
I'll demonstrate that on the next one.
And I'll do that before I paste out the cloth.
It just gives you a line to paste to when you're putting the adhesive on the cloth.
I'll cut both pieces of cloth so I can do all the gluing out at the same time.
And here I'm breaking the cloth over the edge of the boards, which is just putting a crease at the edge of the boards,
which just lets me know where I have to glue to.
The hardest part for applying the board cloth, I found, was not sweating on the book.
I did end up with one major drop of sweat landing on the leather.
And for the rest of its life, the book's going to have a little dark patch from from because of my hot weather.
The first time you open the boards after putting the spine leather on, the boards are going to be, the opening's going to
be very stiff. So just open it gently.
After it's been opened once, it'll open up fine.
Now, with all this opening and closing of the book, I'm worried about getting a crease in the spine.
So I'm going to open the book like you should open a book for the first time.
So just go through opening a few pages at a time and pushing them down firmly and work your way to the center of
the book. I probably should have done this or could have done this earlier, maybe even before putting on the board
cloth. But I'll do it now just because I was starting to get a bit nervous about that.
And I'll do it once again after the book is completely finished.
So I'm just trimming the endpapers up about a half a millimeter, because I know these are going to stretch a little
bit and I don't want them to extend past the text block.
I don't want to be able to see the paste down when the book's closed.
Now, you could also fill in on the inside of the boards.
I'm just going to trim up a little bit, but I'm not going to fill them in.
If you do want to, it's pretty much the same as filling in the outside of the boards.
So for this book, we put down the endpapers are closed.
So glue out the endpaper.
And I like to hold the endpaper, put a little bit of tension on it and try and roll the board down onto it.
And that usually avoids any creases.
What always avoids creases, I've found.
Plus, this endpaper is a made endpaper, so it's quite stiff.
So it's not prone to creasing anyway.
And that's why I've used straight PVA.
If I was worried about creases, then I'd use mix.
Put in a fence. And if you're going to open it up and just check for creases, turn the book over so that the side
that you've pasted is down.
And do the same for the other side.
Now put in barrier sheets or fences between the paste downs and the text block.
And I'm going to let that dry overnight under a bit of light weight.
I put the knitting needles in for good measure, just so that the leather is well forced into the joints either side
of the tab that went into the split boards.
Now, we should really do a label for this book, but I'm going to leave that for another day.
So it does look pretty plain.
So I was thinking about doing a little bit of blind tooling just with a sharp bone folder.
So I found my sample corners and hopefully you've done a sample test corner as well.
So you can use that to just try this out with the sharp bone folder.
Just put a blind line in, maybe 3 millimeters or a bit more in from the cloth.
And if you're happy with that, you can do it on the book as well.
That's the half leather library binding done.
I hope you've had a chance to make one of your own and that it's worked out well for you.
If you have, I'd love to see the photos.
The next couple of videos will be technique videos, and then we'll get back into another project.
If you want to be notified of my future videos, please hit the subscribe button.
I really appreciate the feedback.
So if you've enjoyed these videos on the library binding, please hit the like button.
I also enjoy reading the comments.
And so if you've got any questions or comments, please put them below.
So until next time, cheerio.
