19th Century Half Leather Library Binding Part 3 of 4 // Adventures in Bookbinding

Sparky Deal
161 followers
4 Video Views·Jun 25, 2023
The good news, the book's finished.
The bad news, it's not finished in this video.
So unfortunately, it's going to be a four part project.
And the reason is because of corners.
So my intention for this project was to focus on two new things, and that was an introduction to working with
leather and edge pairing of leather.
Last week, we finished up having attached the split boards.
I had intended to go a little bit further, but I'd absentmindedly rounded the corners of the boards, like I'm
doing right now with the sanding block.
Now, that was not my original intention in this project.
Instead, I was going to do square corners like this, and I was going to turn in the leather over the corners just
like a cloth corner.
So I can't put the corners back on.
And last week, I hadn't made up my mind how to deal with that.
So during the week, I thought about it and decided I was just going to move forward with showing how to do both
types of corners.
So I'm going to start this video by looking at two options for doing corners, one being a very sharp corner where we
turn it in just like a cloth corner, and the other is a rounded corner where you pleat the leather.
And I'm going to go on and do the project with a pleated corner, but I would recommend that you don't round the
corners and you do the square corner instead.
So I'm going to start this video by demonstrating the two types of corners.
So we'll start with the square corner, which we'll treat just like a cloth corner.
So we put it in place so there's enough leather that it will come up about a millimeter past the top of the board.
And then we'll turn in the head, as you always turn in the head and tail first before the fore edge.
So we turn in the head.
Then the little piece of leather that extends past the board, we'll push that down so it's flush against the top of the
board. And then we'll turn up the fore edge, just like we were doing a cloth corner.
So the result is a really nice, neat corner, and it's really easy to do.
And I highly recommend that that is the corners you do on your first project.
Now I'll demonstrate a pleated corner.
So we'll put the piece of leather in position, the same as the other one, so that the leather extends about a
millimeter up past the top of the board.
And I'll get the squares even.
And then I'll bring up both the, both turn ins at the same time.
And then I'll use the tip of my bone folder to start to form pleats at the corner.
Now, leather, when it's wet and had a lot of paste put into it, is beautifully pliable and moldable.
So you just gently work away at it to form a nice, turned in, smooth corner.
The other thing is that paste, you can always wash or wipe paste off leather.
So you can use it as a bit of a lubricant.
So I'm just using a little bit of paste on the leather just to keep it nice and smooth, to try and minimize
marks that I might put on the leather by working it.
Now, this leather is smooth.
With a grained leather, you can always hide the pleats to some extent in the grain, but you'll never hide the
pleats completely on a smooth leather like this.
So here you see the results, the square corner, which looks pretty good.
And then the rounded corner.
This one's not totally dry, so that's why it's a little bit darker still, but it works out pretty good.
So we're going to start by rounding over the edges of the boards just a little bit, just to take the sharp edges
off, both inside and out.
And here is the issue, as I started to round these corners without thinking.
And once I'd done that, I was pretty much committed.
Now, because this is a library binding and we're going for absolute maximum strength, and the head and the tail or the
edges of the book is where the most wear is, and we don't want to pare the leather at these points because of that
maximum strength thing, this rounding of the edges of the board helps with the turning of the leather around the
board. I normally don't do this sanding on this bench.
I try and keep this bench quite clean.
I'd normally go out to the other room to do the sanding, but the other room isn't near as nice to film in.
So I'm going to do it here, but I'm going to clean up really well after I've finished sanding.
So it's something to keep in mind as well when you're doing this.
So we're going to extend the leather about a quarter over the book.
So I've measured from the outside of the spine to the fore edge, divided by 4, and then added 3 millimeters for where
the board cloth is going to overlap the leather.
Now, I've measured from the outside of the spine onto the board, but I always prefer to measure from the edge of the
board. So once I've found that measurement, I set it on my dividers from the edge of the board and then transfer that
down to the tail and to the other side of the book and rule the line where the leather is going to go to.
Now, I want the leather to extend diagonally the same distance in, so I can, there's a couple of ways of doing this.
So you can draw a line in diagonally, measure in the distance, and then draw in the diagonal line where the leather's
going to go. Once you've got that, you can measure how far
along the fore edge and the head that goes.
I'm just checking that it's the same and that I've got that at 45 degrees.
And then, then you can transfer that to the other corners and then draw in the diagonal line.
Now, I can't recommend this enough.
Don't do your first corners on your actual book.
Cut some practice boards and cut some practice corners out of leather, out of scraps of leather, and do at least
four corners, especially if you're wanting to do a pleated corner.
Make sure that you can do four of them in a row without a mishap before you attempt it on your book.
Now I'm going to make a template for cutting out the leather corners.
Now, the corners went in 60 millimetres on the boards, but there's also two 20 millimetre turn ins.
So I'll measure in 60 plus 2 times 20.
That's a 100 millimetres.
And then I'll mark those two 20 millimetre turn ins and mark those as well.
Once I've got that, I'll cut off the corner.
Now I want the leather to extend about a millimetre over the boards.
The boards are 3 millimetres thick, so I'll go out 4 millimetres from the corner.
I'll just judge that by eye and then cut off the corner.
Now I'm going to determine the width of the piece of leather that's going to wrap around the spine.
And I'm going to use a scrap of leather to do this.
So I'm going to force that leather down into the joints so that I've got a good feel for how much leather I'm
going to need, including the amount of leather that's going to go down into the joints.
So I'm going to measure that and then I'm going to add 2 millimetres.
So a millimetre for each side, just because I nearly always come up 2 millimetres short or a millimetre each side.
So it's 112 millimetres and the turn ends are 20 millimetres at head and tail.
So the height is going to be 250 millimetres.
The kangaroo skins that I'm going to use have lots of little blemishes.
And so I want to pick a piece that doesn't have many marks on it.
So I'm going to cut out a little jig that will help me see a piece of leather the size that I want and find a piece
that hasn't got many marks on it.
So that's the size of the piece of leather I want.
Here's the two pieces of the types of leather, the colours of leather that I'm considering.
And for some reason, I'm going to go for the dark brown.
So I got these skins off the bargain table at Packers Leather, and it's pretty obvious why they were on that table.
So this is a typical kangaroo skin.
So that's the tail at the bottom, the legs, that's the tail that I'm holding.
That's the legs and that's the neck area up towards the head.
So you can see this one's quite, quite a mess at the shoulders.
This one had a lot of marks on it.
So kangaroos, they fight and they've got sharp claws.
They get caught on barbed wire fences.
So it's difficult to find kangaroo skins without lots of marks on them.
And these obviously were heavily marked and didn't even make their third grade and had gone on to their bargain
table. Now, this one's actually quite good.
It's a lot better.
But for some reason, someone had cut out a little square from it.
I didn't do that.
That's how I bought it.
And I assume that's why it was on the table.
Now, for a piece of leather that's going to wrap around the spine of a book, I normally like to have the spine of the
animal on the spine of the book.
However, the spine on this skin is just so heavily marked that I didn't want to use it.
So I've found an area where there aren't too many marks.
There are still a few.
And I'm just going to mark the corners with a fairly sharp bone folder, and then I'll cut out the piece of leather that
I want. Now,
I'm going to look for some leather that I can use for the corners.
And once I find the general area, I'll separate that piece of leather from the main skin and then cut out the corners.
First, I'll just finish trimming up the spine piece of leather.
Now, I'm not an expert at pairing leather, and the styles or the techniques for pairing leather vary so dramatically
that there's just no correct way.
I think all you can do is develop your own style.
And so what I'm going to demonstrate is what I've developed for myself.
Now, the main thing is to have a sharp knife.
So the first thing is always to hone your knife.
Now, my technique is to put my thumb into the back of the knife and then my index finger puts downward pressure at
the leading edge, and then my other three fingers wrap around to hold the angle and height of the blade.
I position the tip of the blade about 5 millimeters away from the edge of the leather, and that slides along the top
of my pairing surface.
And I just try and keep that angle on the blade as even as I possibly can.
And the pressure and the speed, again, consistent.
Now, for this project, you don't need a edge pair that extends a long way onto the leather.
I'm only going to go maybe 8 millimeters, 10 at most.
But you still want to work your way down.
So you start with a fairly steep cut and then you come back and lower the angle of the blade slightly and go a bit
further and maybe go a third time until you've achieved the edge pair that you're after.
So once you find a technique that's working for you, you want to make sure that you can repeat it over and over again.
And that just requires lots of practice.
So don't expect to cut your spine piece and your corners and pair it straight away.
You need to practice pairing and then even practice doing some corners.
So you should cut a few extra corners, but start with just some straight strips of leather and start by practicing edge
pairing on those strips of leather.
And then once you think that you can do that repeatedly, then you can practice on your practice corners before working
on your actual corners.
Now, most tanneries will sell offcuts from some manufacturing process.
So all the tanneries in Australia will sell these 1 or even 10 kilo bags of offcuts.
And these are fantastic for practicing pairing on.
So then you can just do it for an hour.
Practice, practice, practice.
You want to get the leather thin enough at the edge that when you turn it over, you can hardly feel it through the
outside piece of leather, because we're going to turn these in at the head caps.
And if the leather's too thick at the edges, it will be quite noticeable.
It's still going to be noticeable because it's at the ends, there's still going to be two thicknesses of leather.
And you can reduce that by pairing in further with a spokes shave.
But this project's about only using an edge pairing, so I'm not going to do that.
And we'll just accept that there's going to be slightly thicker leather at the head and tail of the spine.
Corners are a bit of a pain in the neck and there's just not much to hold on to.
But with a bit of practice, it works out OK.
And a bit of relaxing music really helps as well.
Did I mention that having an extremely sharp knife is important?
I haven't shown every time I've sharpened it, but I pretty much strop it after every corner.
Because this is a completely new process for my videos, I'm not speeding it up too much.
Actually, most of it I've kept at real speed.
And when I have sped it up, such as this part, I've only sped it up slightly.
So if edge pairing is something that's not new to you, then go ahead and skip forward a couple of minutes.
Now, the last thing I want to show you is another way of using an English style pairing knife, and that's to do a
heel pair. Now, I quite like this technique, but I'm not very good at it yet.
So I don't normally use it, especially for small pieces of leather.
I just really struggle with small pieces of leather.
But for getting a zero edge, an edge that goes down to absolutely nothing, then I've found that heel pairing works
really, really well.
We're going to finish this video by putting the corners on the book.
So we're going to start working with leather.
So the first thing we're going to do is moisten the outside of the leather.
And there's a couple of reasons for doing this.
So the first one is that when you get leather wet, it normally darkens and it even once it dries out, it doesn't go
back to the original color.
So if you get a spot of water on the outside of a piece of leather, often that drop, that spot will stay.
Now, the same would happen if you put adhesive on the on the piece of leather and it soaks through to the front.
That spot, that mark from the moisture will remain.
So by wetting the leather completely, when it dries out, it'll dry out to the uniform color that it wants to go to
having been wet.
So by moistening the complete outside of the leather will stop any strikethrough marks showing up later.
Now, the other thing is that we want the leather to be soft and pliable, and wet leather is extremely moldable.
And that's a property that we want.
So what I've done is I've moistened the outside with a sponge, then I've put a layer of paste on the inside of the
leather or the leather that's going to go on the on the book.
And then I've faced the two corners together and I'll occasionally moisten the outsides because it is so dry here at
the moment that it's just drying out before I've got everything in place.
So I just want to keep it moist.
And the other nice thing about that is it gives me lots of time to work, so I don't have to rush.
Now, the leather absorbs the paste, which is what we want it to do.
So once I pull these corners apart, I'll give them yet another paste before I put them on the book.
I'll use the lines I've drawn on the boards for the initial positioning of the corner pieces.
But I'm probably going to move them around a bit, so I'm not going to press them down hard onto the board at this point.
So I'm going to open up the boards and adjust the squares or the turn ins, sorry, so that they're even and so that the
piece of leather at the corner is going to extend about a millimeter over the corner.
Notice how I'm using a couple of pressing boards to support the covers or the boards while I'm working on the
corners. So here I'm going to do this pleating technique that I showed at the start of the video.
Leather can be an enjoyable material to work with.
The moist leather and the use of paste means there's no rush.
If something's just not working out, you can actually take the leather completely off the book, repaste it and start
from the beginning again.
One of the downsides is the moist leather is very delicate.
It's very easy to accidentally push your fingernail into the leather and leave a permanent reminder of your
mistake. Or maybe it's a new feature.
But I prefer to not leave my fingernail marks on my books.
When working around the edges of the boards with the bone folder, it's very easy to get carried away and put little
dents and marks in the leather.
So it's you just have to be mindful and be gentle with the leather.
And once I've got these two corners on and turn the book over to do the other two corners, I'm always going to have a
piece of thin foam underneath the book.
I don't want the leather being dragged across the really rough surface of my workbench.
I want something under the book that so that when I rotate the book, I rotate it by rotating the material under the
book, not the book on the material.
The leather holds a lot of moisture, so you really need to put a barrier sheet in between the boards and the text
block. This is my favorite piece of foam that I've had for almost a year now that I do use for all my leather
So I'll just let it hang over the edge of a of a board so that both sides can dry evenly.
So I hope you've enjoyed today's video.
I really appreciate it when you hit the like button for my videos and let YouTube know that you've enjoyed them.
We're on the homestretch now.
If you want to be notified about my upcoming videos, please hit the subscribe button.
And until next time, cheerio.
