6 Simple Steps To Get A PERFECT BASS Mix In Your Tracks - Music Production

Born To Produce
287 followers
234 Video Views·May 29, 2023
Learn what it takes to get a perfect low end mix in your tracks. Bass mixing in music production can be a bit of a dark art. Here Jon from Born To Produce shows the 6 steps you need to be aware of in order to get the perfect bass mix in your own tracks.
If you want more info on this, then head over to https://www.borntoproduce.com/ and check out our pro tutorials on how to get better at mixing, or to learn to make specific genres of music in any DAW. Thanks for watching!
In today's lesson you're going to learn how to get the perfect low end mix every time
in six simple steps. Don't go anywhere.
Hey guys, I am Jon from born2produce.com and step one for getting the perfect low end mix is
use the right equipment. If your studio monitors don't go down to a low enough frequency
you won't be able to hear the sub and if you can't hear it then you can't mix it.
If you're on a low budget and you can't afford a decent set of monitors then a half decent set
of headphones that go down to at least 20 hertz might be your best bet. Also in most instances
the room will have an effect on the bass image unless it's acoustically treated. You can use
headphones to avoid this or you can buy acoustic panels to put in your studio space. The ready
made ones can be quite pricey but you can make your own like I've done for a lot cheaper.
Step two, pick the right sub bass. Now this is vital and just like you would spend loads of time
picking and tweaking a lead sound you need to take just as much care picking and tweaking the
sub. Take your time and make sure it fits with the rest of your track. Step three, make sure the kick
is tuned to the melody of your track. If you're using a kick that has a good bit of sub presence
then this is vital and if you get this step wrong it won't matter about getting all the other steps
right. If you're using a very short attacking kick then you might not need to worry about this so
much but six times out of ten I tune the kick. So here I've got a little kick and bass line.
Now what I'm going to do is just open up the settings and add a scope to the kick channel
and I'm going to use this to analyze the kick. So what we're looking at with the
kick frequencies is this very lowest peak right here which basically represents the sub bass
frequencies of the kick. Now this is the important bit that we need to tune. So at the moment it's
telling me that the kick sub is in C sharp okay and the actual bass line for this track, let's
just bring that up. This is in A minor, A being the tonic. So I could tune the kick to preferably A
which would be the best or I can tune it to pretty much any note in the scale which is any of the
white notes in this case. So my kick is or the analyzer is saying the sub bass part of my kick
is in C sharp okay. So I don't want it to be in C sharp. I could probably tune it to be in D or C
or I can bring it all the way down to A. So let's try that. So let's just count. So we've got C sharp
so we want to come down one, two, three, four semitones and that should tune our kick to be in A.
So let's just have a look at that. So we've got my controller for the pitch. So I'll bring it down
four semitones and there we go. We can see that the peak has moved down to A. So I know
that the sub bass of the kick is now definitely in the same key as the bass line. Step four,
sidechain. Yes that's right, another vital step to make sure the kick and sub play nice together.
If the kick is playing on its own that's fine, if the bass is playing on its own that's fine,
but when they play at the same time you get a very messy low end because of the combined sub
bass frequencies from both. That's right, to stop that disaster you have to use a sidechain
compressor to duck the volume of the bass line whenever the kick hits. So I'll stick my compressor
on the bass line, turn the attack and hold off, put the release down a bit, ratio can stay around
there and then in my kick settings I'll use a send to send a duplicate of the signal through
to the sidechain compressor. Activate the send and we're good to go. Then you can adjust the
threshold, the release and the ratio depending on how much sidechaining you want. Simples!
Step five, mono the sub bass. Now your mastering engine is going to do this anyway. Why? Because
the human ear is not great at telling the direction of sub bass and as bass frequencies
need a much higher amplitude than other frequencies due to the non-linearity of the human ear,
having it panned more to one side will create an out of balance energy distribution. That's right!
So we always mono the sub to make sure it's stable on both left and right channels which gives an
overall punchier and stable low end mix. I usually set the mono maker plugin up on the bass group
but sometimes on the individual bass elements if one of the elements has a lot of panning on the
low end. 80% of the time though it's just on the bass group and I usually choose to mono any
frequencies below between 120 hertz and 80 hertz but this will depend on the mix. Step six, make
room for the sub bass in your mix. Okay so to create a bit of space in your mix for the sub
energy of the track we're going to route the kick and bass elements that is anything with a strong
sub presence to its own group and I'm going to route that through to a bass out group that I've
already made and that'll be for the kick and the side chain bass group which is all of the bass
elements in this case. So now I have like one master fader for all of the bass elements and of
course that group also has our mono maker plugin on it and then we're going to route every single
other element in the track through a pre-outs group. Now this is a pre-made group you can just
don't have to call it pre-out you can call it whatever you want but it's important that every
other thing apart from the bass elements go through this one group. So I've already routed
pretty much everything through the drums, the leads, the vocals, everything all going through
this pre-out group so that gives us again a fader with everything minus the bass and then what I'm
going to do to create a bit of space for that sub I'm going to grab an EQ plugin. I'm going to have
a use a fairly steep cutoff filter basically 96 db is quite good but turn on linear phase so you
don't get any nasty phasing artifacts from the EQ and then we're going to use it just to filter out
any of these sub frequencies usually anything between 80 to 100 hertz and below. Now that
frequency will depend on your mix but you would not usually go much higher than 120 hertz as you'll
start taking too much low mid energy away from the rest of the mix which you definitely must
avoid. If you're not sure just keep this below 100 hertz and you should be fairly safe and all that
does is it just stops any sub frequencies in any of the drums any of the vocals anything like that
conflicting with the sub of the kick and the bass keeping it nice and clean. So there you are the
perfect low end mix in six simple steps of course that is a very brief look at how to do it if you'd
like a much more detailed look at how to get the perfect low end mix in every tune you make and a
whole load more mixing skills like how to get a massive vocal or lead sound how to create a real
sense of depth in your mixes plus an absolute ton more then visit born2produce.com and check
out our mixing masterclass course. It's basically 17 years of mixing experience boiled down into
four hours. The link is in the description thank you for watching.
