How to make a Rustic wooden American flag shaped like the USA . Projects that sell. Unique and easy

The Next Fixit
86 followers
2 Video Views·Mar 17, 2023
Hi.
Today, we're going to build a wooden rustic American flag cut into the shape of the United
States.
This is one of my best-selling flags, and today we're going to show you how to build
it step-by-step.
So, now we're going to set up our saw so we can cut our boards, and we want to set it
up for 35 1⁄2 inches.
So I have my stop set up, and I'm going to use my tape measure, 35 1⁄2 inches.
So every time I put a board up to that stop, it's going to be 35 1⁄2 inches.
We're going to take these 1 by 2s, they're six feet long, so we should get two out of
each of them.
I'm going to cut two boards at a time.
Push it up to the stop, hold it tight, there's two, and we need 13 of them.
So now I've got a nice smooth edge here, we'll put this on down here, pop it on again, that's
four.
Okay, so now we've cut our boards, we need 13 of them.
And now we're going to take our torch, and we're going to burn the wood, and it's going
to make the grain turn dark.
We're going to burn the face of it, and I like to burn the edges also, that way when
you put the board together, if there's a little gap or anything in it, you won't see the white
wood on the inside.
Now we're going to burn and texture it.
Okay, so now we're going to take this small torch, I use map gas because it gets a little
hotter, I like that.
You can pick this up at any of your neighborhood Ace Hardware stores, it works really great,
it lasts a long time.
So to burn the face, we're just going to move it along slowly, and you'll see it, get the
edge.
Okay, so now we've burnt all of our wood, and now I've made a little jig on my table.
I've got one by here and one by here, and I have them set at a 90 degree angle.
So when I put my boards in here, I just push them up tight, and it gets them all even.
And when I clamp it, it'll pull it down to it.
So now we're going to lay out our union, which is the blue background for the stars.
And we know it's seven stripes, and it's going to be 14 and a half inches in.
So we're going to measure in on our seventh stripe, 14 and a half inches.
And on the top, measure it, 14 and a half inches.
Alright, so now we know this is going to be our union.
Make sure they're all up even.
This is going to be our straight edge.
Line up our marks.
So this is going to be our union.
So now we're ready to stain.
So what we're going to do is we're going to take these blades, and we're going to lay
it on the line, like so, and just tap it in.
So we can stain this blue and then this red, and that's going to keep our stain from bleeding
into each other.
It's a very simple, easy way to do it.
Okay, now we've put our utility knife blades on the line, and this is what's going to keep
our stain from bleeding into each other.
So now we're going to do the blue for our union.
Let's take a little bit of stain here.
I always stain the edges.
And get right up to that blade and drag it back.
I always do the sides.
That way if the wood comes apart, you won't see the blonde wood behind it, you'll just
see the blue.
It doesn't take a lot.
This is a water-based stain.
This is called Denim Blue.
Make sure we get all the way up to the blade.
We don't have to do the edges because we're going to be routing this out and the edges
will be gone.
If we were just making a standard flag, then I would stain the ends of it.
Okay, so now we've done our union.
Now we're going to do our red stripes.
So every other stripe is going to be red.
So I kind of laid them out so I know which one's not the stain.
So we're going to get right up to our blade.
There's no need to wipe this off because once it dries, it's done.
It stains really well.
Make sure we do our edges.
This is called Crimson Red.
You can put two coats on if you like, if you like it darker or not.
Okay, now we have them all stained.
Now we're just going to take our blades out.
And you see it's a nice straight line.
No bleed through.
I've tried tape and a few other techniques, but this seems to work best.
And now we'll let this dry for a little while and then we'll glue it together.
Okay, so while we're waiting on our stain to dry,
I'm going to go ahead and get the stars painted.
I buy these wooden one-inch stars off Amazon.
They're really inexpensive and you can buy them by the thousand or a hundred,
whichever one you prefer.
I'm just going to lay them out and I'm going to use my Ace Hardware gloss white paint
and I'm going to paint them.
I'll start out painting the sides, each angle,
try to get the sides of the star, and then we'll come across the top.
It takes about three coats.
Just put it on light.
Alright, we'll let that dry and we'll come back and put another coat on it.
Okay, now that our stain is dry, we're going to glue it up and clamp it.
And then as soon as that glue dries, we'll be able to take it and route it
and cut it in the shape of the United States.
So we're just going to put some glue down the side.
Snug it up.
So once I get a little bit of pressure on it,
now I'm going to tap it down.
I want to make sure our union is straight.
A little pressure.
Too much pressure and it'll bow up.
As we clamp it, you'll see some of the glue start to ooze out.
So we'll just take a damp rag.
You don't have to get it all because this glue dries clear.
But I like to wipe it off just in case.
So now we're going to try to get our boards a little even.
You can just tap them down.
Sometimes they want to bow up on the end,
so I'll just take another clamp right here and just lay it on the end.
Hold it down with just a little bit of weight.
Also want to note, we put wax paper underneath our flag
so it won't glue itself to the table because it's got to sit for a couple hours.
I usually let it sit overnight.
Okay, now we've let it sit.
The glue is dry.
We unclamped it.
Now we're ready to put our stencil on here and trace out the United States.
And then we'll take our router and cut it out.
Okay, so now I have it just halfway on my table and I have it clamped down.
You have to keep it nice and sturdy or your router will jump around and it could break the bit.
I'm going to use a quarter inch router bit
and we're just going to walk around and follow this black line all the way around.
When I get here, I'll stop and move it and clamp it again.
Okay, so now we've got it all trimmed out.
And you can still see a little bit of the ink around the edges, which is fine.
I'm going to take a piece of sandpaper and we're just going to soften up the edge a little bit
and it will take that ink right off.
And get rid of this rough on the bottom too.
I've gone back and sanded the edges.
And it's okay if you still see a little bit of the black marker
because we're going to go back and burn these edges.
But in order to give it a good three-dimensional look,
I'm going to go back and paint these edges.
Where the red, red, red, I'll paint on these lines.
I'll just do it by this brush.
And once I get the red done, I'm going to do the union on this side
and then we're going to go back and burn it.
So I'm going to do that now.
Okay, so we've gone and used a little brush
and I filled in where every stripe is.
I did the blue on the side of the union.
It gives it that real thick, dimensional look.
It makes it look like they wrap around.
So now I'm going to take the torch and we're going to burn these edges
and give it that real rustic, burnt look on the sides.
I've got to burnt all the edges.
It really gives it a real rustic look.
And now I'm going to clear it.
I'm using the One Coat Polyurethane Water-Based Clear.
Just don't put it on too thick.
One Coat does it.
I'm going to do the edges first and then I'll coat on the top.
Alright, now we've let our clear dry overnight.
So now it's time to lay out our stars.
I have this simple stencil that I bought off Amazon.
I think it came in a pack of three.
This size, a few smaller sizes for like $12.
We just pretty much line it up on our union.
It's already made to the right size.
We'll tape it down.
Then we take a magic marker and we're just going to mark where the tips of the stars go.
Where the tips go past the flag,
we'll just mark the bottom of the star so we know where to put it.
And then on the rest of them we just mark the very tips.
This star here, it isn't enough to be on the flag so we won't bother with it.
Okay, I know it might be a little hard to see,
but at the right angle you can see the little black tips
wherever the star is going to go.
So we're going to take some clear Gorilla Glue
and we just put a little bit of glue on the star
and we'll just manually put it on there by hand.
It's pretty easy to do.
Put a little bit on the star.
Line it up on the spot.
And you can use the line and the board as a gauge to keep it level.
It makes it real simple.
We'll just put some glue on these.
All you've got to do is look for the spot on the star.
And this stuff dries clear.
So if a little bit oozes out the side it doesn't really matter.
And once this dries we're going to come back and cut the tips off these stars that are sticking out.
So I'll go down the line and just keep adding the stars.
Okay, now that we've let the glue dry
and you see all our stars are on our union
we still have a few stars that stick out just a little bit past the flag.
So I'm just going to take a grinder and just gently grind off that edge.
Gently.
So I'll just grind off just the tip of it.
And then I'm going to take a little white paint and just touch up the tips.
Alright, so now I've ground off the tips of the little stars here
so you see it's just a plain wood
so I just take a little bit of white paint
and I'm just going to touch the end of the star a little bit
just to make it white.
And this one over here
there's a little bit on that end that I take off.
And so here we have our finished product.
I think it turned out great.
I hope you enjoyed this video.
If you did, please hit the subscribe and like button
and follow us for more projects.
Thanks.
