How to Make a Coping Sled | Woodworking Tools

MWA Woodworks
11 followers
11 Video Views·Feb 26, 2023
Hey guys, welcome back to MWA Woodworks. My name is Matt and in this video I'm going to be showing
you how to make and use a coping sled. Actually, two coping sleds. This one that I built out of
scrap plywood and this other one that I built out of aluminum extrusions which I purchased
and assembled myself. Now making the groove in the profile cut is easy. You have the long edge
of the workpiece against the fence and make the cut nice and safe with some hold downs to keep
everything in place. But when it's time to make the coping cuts for the mating pieces you're
cutting the end of the workpiece. This is obviously a much more precarious cut because only a very
small part of the workpiece is in contact with the fence. You could use a piece of scrap to back up
the cut and give the workpiece something to ride against but there's nothing to keep it from sliding
back as you make the cut and creating an ill-fitting joint. This is what the coping sled was made for.
It consists of a base for the workpiece to ride on. There's a stationary fence on the right side
that provides a nice sturdy and square edge to ride against. There's a movable fence on the left
side to hold the workpiece laterally and a clamp to keep it held down in place. It should also have
sturdy handles for guiding the sled and a reference edge to guide the sled a fixed distance from the
fence as the sled moves across the bit. And you can see here in this demo with the workpiece backed
up by a piece of scrap to prevent blowout I can complete this cut safely and accurately. And that's
what gives you a tight fit like this. The cope cut fits perfectly over the profiled edge leaving you
with a clean joint. So for the plywood coping sled I start with a blank and use a forstner bit to
countersink holes where the t-nuts will go. I need two for the guide post, two for the stationary
fence, and two for the handles. Next I adjust my drill press table upward so that I can cut through
holes for the center of the t-nuts. These holes will allow us to attach everything but the sliding
fence. To make the sliding fence, well, slide I need to first route a groove down the center of the base.
It needs to be deep enough for the head of a hex bolt to slide below the surface.
Then I switch to a smaller bit to cut all the way through creating a groove for the sliding fence.
Next I install my t-nuts and one of my favorite ways to do this is by using a clamp. It makes
pressing them into the plywood a breeze. Oh yeah, I ended up adding counterbores to the top so that
the handles would reach the t-nuts. Those go in first nice and sturdy. Then on goes the stationary
fence with two bolts. Before I tighten them down all the way I'm going to use a square to align the
fence. Next I slide a hex bolt in the bottom of the groove and I add the sliding fence. And I'm
using a knob to tighten the fence down. Now I add two standoffs that are going to act like
guide posts. These have a male thread on one end and a female thread on the other. Okay, for the
fence guide I cut a piece of six inch polycarbonate plastic in half at the table saw and I add a
locator hole on each end and then pick the plastic swirly piece off the drill. Okay guys, one thing I
recommend on this polycarbonate shield is to go ahead and use a router to add a small chamfer
all the way around the edges. I did about a sixteenth of an inch on both sides. This stuff
is sharp as crap on the edges. As I found out the hard way, I cut myself more than once as I was
fiddling around putting this jig together. So go ahead and save yourself that trouble and add the
chamfers. So with the chamfer bit in the router table, I took my own advice and trimmed every
edge on this polycarbonate to avoid any more future cuts. And I added the guide to the guide
post securing them with two cap nuts. I left the cap nuts loose at first and tightened the guide
posts all the way down. Then I went back and tightened the cap nuts fully using a hex wrench.
And last but not least, I added the clamp and give it a test. Good news, it's clampy. All right,
that's it. Our coping sled is now complete. Now I really like this version of the sled. It's very
lightweight but sturdy and it's relatively cheap because I was able to use scraps of plywood and
only purchased the hardware for it. And if any of these fence parts get worn out, it's easy to cut
new pieces and replace those. Now what if you don't have the scrap to build this and you don't
want to buy an entire sheet of three quarter inch plywood just to build one small jig? Well, that's
where I've got you covered with version two of the coping sled. Now this uses all the same hardware
but it uses aluminum extrusions for the fences and the base. And that's going to make this a
much more sturdy stout jig. And it's also going to be more configurable because you can move things
around in the grooves of the base. It is going to cost a little bit more money for these aluminum
extrusions but you're not going to be spending as much money here as you would be if you were
buying an entire sheet of three quarter inch plywood to build this jig. I will leave a link
in the description below for all of the parts and the aluminum that I'm using to make this so if
you'd like to go this route you can purchase those yourself. Now let me show you how I built it.
Now the only real work that's needed to be done here to these parts is to drill holes in the
fences so that we can attach them to the base. I located the position of the holes with a center
Aluminum is a soft metal and you may not know this but you can cut it with regular woodworking
blades and drill bits like I'm doing here. Now you can order these parts with the holes already
drilled for you but in my opinion they charge way too much for that operation and it takes
five minutes to do it yourself. Now let the assembly fun begin. This time I need to add the
stationary fence first. Now you'll notice that I did add a small bit of half inch ply to the top
of the fence and I'll explain why later. By the way this time I'm using sliding t-nuts to go in
the grooves of the base and hold everything in place. Now like before I use a square to get the
fence lined up. Then I slide on the movable fence. Then I added the clamp. This is why I added the
scrap of wood. Now you're probably saying to yourself didn't he say I could build this sled
without any scrap plywood? Absolutely you can. You can screw this clamp directly into the aluminum
fence just using regular steel screws but I was non-committal at first about where I wanted the
placement of that clamp to be and I thought it would be easier to just add the scrap plywood
to screw into so that I could move that around easier and not make a bunch of holes in my
aluminum fence. So if you are better at making a decision and sticking to it than I am by all means
lose the scrap plywood and screw it directly into the fence and that's also going to save you from
having to use this longer bolt as well. The bolt that comes with the clamp will work perfectly fine.
Next I add the handles. Now there's several places you can put the handles which is why I like this
version of the sled. Same thing goes for the standoffs and I added a regular hex nut to these
because the thread was too long and it bottomed out in the groove before it was tight. So that
hex nut just acts as a little bit of a spacer. Then I just added the guide and tighten it in
the same order as before. Now my indecision about the clamp came back to bite me here.
You can see that the clamp head doesn't reach the workpiece because I added the ply.
So I opted to make my own longer clamp head using a t-bolt and another scrap of plywood.
I drilled out a pocket that the head of the bolt would fit into. I then mixed up some five minute
epoxy and added it to the recess and then sank the head of the bolt in there and let it dry in place.
Once it was dry I went ahead and added it to the clamp and the problem that I created that
didn't have to exist to begin with was solved. Now this sled is truly a beast. It's much more
stout and feels beefy and the nice thing about the grooves in the base of the sled is that you
can change configurations. And here you can see this sled in action. Well hey guys I really hope
you enjoyed this build and you learned something new today and if you did please leave me a thumbs
up below. I would really appreciate that and also leave a comment to let me know what you thought.
Also please hit that logo icon to subscribe to my channel. I would really love to have you on board
and also make sure that you hit the bell icon to be notified of future videos. Speaking of videos
I've got a couple other shop builds lined up here that I think you guys might enjoy as well
so please check those out and until next time have fun in the shop.
