Harbor Freight 34706 Woodturning Lathe Review || 12 x 33 wood lathe (2022)

Motivation Monday
96 followers
27 Video Views·Feb 24, 2023
What is up YouTube tooltubers of the world my name is Brad. Welcome to the workbench and today we're
going to look at the old girl that really kind of took my life in a whole new direction and that's
the central machinery wood lathe. I've used this lathe for over two years. I actually just broke
it. I'll show you quick details of that so I'm gonna have to upgrade. But in this video I'm
going to show you a lathe that was pushed to its absolute limits, the good things about it,
the major design flaws it has, and maybe let you decide if this is going to be the right lathe
to start doing wood burning. So let me get behind the camera so you don't have to look at my ugly
mug the whole time and we can actually concentrate on the features and perils of this wood lathe.
All right I just want to kind of take a step back and this is as far
and this is as far back as I can get in my little tiny shop here and give you a kind
of an overview. As you can see this is highly modified. I made that shelf there and the
shelf for two things to add storage because I'm in a tiny shop. It also adds weight to the entire
frame of it. If you come down here you'll see real close I had to lift it up. That's about
four inches of lift I put on there and some rubber on the bottom and I'm about 6'2", 6'3"-ish.
So if you're around 5'10", 5'11", this lathe should probably come at the height you need.
Any taller or any shorter you might have to make some adjustments. Now this is listed as a 12 by
33 and a half or something inch lathe which is saying that you have 12 inches of swing.
That's the diameter of a bowl you could turn and 33 and a half inches of travel. I actually haven't
maxed that out and the footprint you'll need basically the amount of space it truly takes up
is approximately 5 foot by 24 inches deep and of course whatever we're talking that's usually not
an issue in most shops and that's if you add this little outboard extension here which is really
nothing more than a nice little table because I definitely wouldn't trust spinning this thing
around. I actually tried to once and it was just a ---- show. Take a quick look at the stats of it.
So your speeds, this is a Reeves drive which means there's two pulleys that can get bigger
and smaller inside. I'll take this cover off and kind of give you a better look at it later
but just know that your lowest speed you can go is 600 which is pretty fast for most bowls
and the fastest speed you can go is 2400. So great spindle lathe or great for spindle work.
Not ideal for bowl turning but doable. Doable. The base they gave you here is just regular old
cheap stamped steel. It works. It's flimsy. You need to beefing it up a little bit in my opinion.
Adding shelves like this definitely adds some rigidity to it but of course this isn't
a high dollar tool. This is a budget tool. This is something that you would get if you're starting
out which I was. I purchased this lathe for $300 approximately about two years ago only because
I had a 25% off coupon and you're really not going to see that. I think nowadays or at the
timing of this video this lathe is selling for about $430 without any coupons or anything like
that. So I think it's going to be best to start out by telling you the things I do like about
this lathe because that list is a lot shorter than the things I want to warn you about before
you buy it. First thing is the price. You cannot deny that this price is a killer price. When you
start looking at wood lathes in this size range you're looking at about $800 to $1,000 average
I'd say in this size range. You know have that full length bed. Now you can get some smaller
lathes that may be better to start out but those motors are so small if you want to do any kind of
bowl turning you really need something a little bigger than the mini lathes they have out there
because even the motor on this one here still struggles quite a bit at least with the bowls
I was turning. Some other features I like is that it does have a 1x8 TPI spindle with a Morse taper
number two if you want to insert a live center into there and also Morse taper number two
on the tailstock. The tool post is one inch. I did have to take some sandpaper in there and kind of
ream it out just a little bit when I bought these because they wouldn't quite fit. Now I don't know
if this is oversized or this is undersized. I didn't put calipers on it. I just needed to make
the ---- fit right. Now the reason I like that is because that allows you to use a lot of the tools
and the chucks we'll get to in a minute on your next lathe when you finally decide you want to
move up. A lot of the lathes that get bigger than this are still going to have Morse taper number
two for the head and tailstock and if they don't have a one inch 8 TPI spindle thread they're inch
and a quarter typically and that's very easy to buy an adapter and unless you're getting into
turning really really big stuff a one inch spindle is still pretty damn sturdy. And so one other thing
I do like that they didn't have on their small Harbor Freight lathe is the self-ejecting tailstock
so you don't actually have to put a bar in there to hammer that out like you have to on the
headstock. You can just back it up and it eventually hits a point so easy enough to take that in and
out. And the last thing I will say is I will recommend this lathe before I'll ever recommend
one of the dual pipe lathes or even worse the single pipe lathes. You saw a lot of them made
in the 80s and 90s. A lot of them are on the used market right now. This will blow one of those out
of the water. All right so my complaints and there's quite a bit so we're just going to kind
of rapid fire them through the list. If you got questions on them leave a comment I'll give you
further detail in the comment section. But centers they don't line up and they've never lined up. I've
never been able to get them lined up. So let me show you what I have to do. All right spur dry we
will bring the tailstock up lock it in. All right so I put a block of wood back there so you can see
how off that is that is terrible that's a probably over an eighth of an inch and that's looking at
from the side we can look at it from above we can see we're also off in that direction about an
eighth of an inch. So I've tried shimming the legs I've reached out to more experienced turners
especially when I was first starting out to figure out what I could do to remedy this and and I
basically found nothing that worked or nothing that at least lasted long term. Even if I shimmed
up the legs to get this to line up you know eventually I hit a wobbly bowl a bowl that you
puts a lot of vibration or rattle into this thing and it would just all go to hell. So what I did
that I found to be the best is I bought the little shim kit from harper crate and I have a little
drawing on here that tells me what I need under each corner to get it lined up pretty damn close.
I'll tighten it up and here we are with the shims now that's still off but that's a hell of a lot
better if you wanted to be more patient and keep working with them shims I'm sure you could get it
even closer but since I broke this lathe I've only been turning bottle stoppers because that's
about the only light duty turning handle so I haven't really worried about this lately because
I don't need a tail stock for what I'm doing but like I said you keep adding these shims under here
and you can eventually find out how to get them lined up almost dead perfect but again you're
always going to have to be checking this to see how they line up you can also clean out your
morse tapers but it's a wood lathe they're going to get dirty you know there's only so much you
can do all right so I've got the board we're using as a background lined up between centers
to show you the next major issue I hate with this machine and as you can see we're we're relatively
at 90 degrees and right here you can see the problem is and you are so close to coming in
right here and hitting this motor and it's shrouding probably about a quarter inch maybe
a little less just eyeballing it and you're going to say well that's not a big deal you're close but
you're not hitting it but I can't tell you how many bowls I started out that I wanted to start
out turning between centers because they were going to be a live edge bowl so I wanted to balance
and move and I had pieces of the bowl coming past here and of course they were hitting that and so
the big issue you have there is you have you know less than four inches before you start hitting
that so if you want to do a live edge bowl that extends past here you're kind of limited to eight
inches or less because of this damn shrouding I hate this design so the best solution I found
to fix this issue is you turn you a nice spacer and you can turn this to variety lengths use a
chuck that'll take a drive center and this still gave me problems on certain pieces because on
on a really wonky piece or something then your chuck starts getting in the way but it does get
you out away from that motor at least by a couple inches so it's just a problem that you get tired
of having to deal with after a while and speaking of little things that just kind of irritate you
after a while is all the little handles this little pot metal plastic stuff they all they all
end up breaking you know because especially you really got to bear down sometimes to get a nice
hold on your tool rest this is my second one actually snag this out of the piece that was
the little extension piece that goes on there if you want to do some outboard turning which I really
highly don't suggest but this would go in there and then that adds some versatility to your lathe
let me show you one other thing I really hate is that there's no handwheel and that really becomes
an issue if you need to thread a project on a spindle like this it would be nice to have a
handwheel back here rather than trying to clutch it up here and that's all you really got and also
when you're applying finish you know you got to sit here and turn the chuck rather than just a
nice handwheel on the back when you're applying finish because your lathe doesn't go slow enough
to really actually apply finish so hand wheel would be killer let's take this cover off I'll
show you the reeves drive how it connects in here oh yeah see because even that one broke
and some other things I hate about this damn lathe in case you've never seen this is how
reeves drive works right here as I change the speed of this spindle watch these pulleys back
here it's pretty cool I've seen uh I've seen videos where people have an issue with these
pulleys not changing size but you know you keep keep it well maintained keep it flowing out keep
lubed up what needs to be lubed up with a dry lube not wd-40 and uh no issues at all out of this
reeves drive my only complaint about it is it doesn't go slower than 600 but that's all of
these so I guess that's just kind of a handicap of this kind of speed control system all right
so hopefully you can see down here because I'm not removing this whole thing I just I don't I
don't like y'all that much uh this ring right here is like a dovetail and it's shaped like that
and it's a ring so it's a dovetail ring I mean there's no other way to say it so there's a clamp
like this on this side and the other side and that's the only thing holding your headstock to
this lathe is basically there's a p there's a rod with the threads that you can put nuts on that go
through there and then it clamps down to that ring that's the only thing keeping it and if you go back
to my uh one of my first woodturning videos this actually loosened up on me over time and just
started going ******* crazy but uh if you wanted to if you really want to you can loosen this up
and then you can remove this pin and it's got a few different angles that you can hit at so you can
see the crack right here this is the clamp on the other side and there is a crack so it's probably
my fault I probably put a little too much pressure on there and broke it or I had too much pressure
on there and then you know I was turning a wonkity piece of wood that was causing a lot of vibration
and a crack during that either way it's because I put too much pressure on it but there's a reason
I put too much pressure on it because it's not a good I don't think it's a good clamping system
at all there's not enough points of contact I would never buy another lathe that had this kind
of clamping system so that can be repaired you could braze that if you have that sort of skill
I myself I'm not gonna worry about it I've been saving up to get a new lathe for a long time now
and I'm gonna do that so let me just break it down to you like this if you're gonna use this
few and far between or for light duty stuff go for it it's gonna it's worth the money it'll do
its job and I've never had a customer ask me what kind of tool or what brand of tool I use to make
any kind of product don't be ashamed that this is what you can afford to get you started and makes
you money that's all that matters if you're gonna be turning bowls and especially odd shaped bowls
or big bowls or uh just just odd shaped objects and you're gonna have to be fighting a lot of
vibrations and stuff you're gonna outgrow this lathe very very quickly like I did I basically
outgrew it within probably six to eight months and I've just had to make it work since then
because I didn't have the money to buy a new one once the crack came along whether it was my fault
or not doesn't matter it's there I need a new lathe I'm gonna go ahead and upgrade since I can
now so I hope all that information helps you in your buying decision either way I think woodturning
is a beautiful hobby if you have any ounce of artistic fiber in your body it might be worth
giving woodturning a try it's good for the soul man it's good for the soul anyways until next time
hit that like button hit that subscribe button we'll holler at you next time
