Wie schwer es ist, ein Tor zu schmieden | SWR Handwerkskunst

SWR Handwerkskunst
8 followers
3 Video Views·Feb 5, 2023
Art. Highest craftsmanship.
Made with precision and dedication.
The payment of my work is not my bank account.
The payment of the work is when someone comes and says,
great, looks good.
The Catholic Church in Korntwig in Westphalia.
The order, a gate forging for the interior, as a separation.
This is the job for Thomas Maria Schmidt near Pirmasenz.
Outstanding as a German blacksmith.
A great challenge in every respect.
This is where the big gate is supposed to go in.
Here we go with the measuring.
An art in itself.
What you can see is that in old buildings or old churches
the symmetry is not right.
But that can be picked up in our craft
to make the symmetry coherent again in the overall picture.
The missing symmetry can be seen particularly well on this floor plate.
The gate arch would be symmetrical
if the laser line in the middle of this pattern were.
Here 5.2 cm are missing.
The arch is measured with a laser.
Zollstock und Messlatte dienen nur noch als Orientierungshilfe.
You can measure it manually with a meter and make a template.
But that's all so cumbersome.
We measure it with a laser.
That means we make a kind of thought-out grid
on this gate or on this pointed arch
to determine the points that can be transferred to the workbench.
And with these points on the workbench
we can trace our pointed arch one-to-one.
In concrete terms, always in 10 cm steps upwards
a horizontal line is drawn between the columns with the laser.
Yes, 10 cm further.
And with another laser the width, the distance between the columns, is measured.
2.47 m
Daniel, one of the two sons of Thomas Maria Schmidt,
writes down the measured values.
The whole thing takes two hours.
We have now measured our points,
we have our guideline from the old building plans
and can now optimise it in the company on the workbench.
Now Thomas Maria Schmidt knows
how high and wide his gate can be
and can then make his sketches.
He already has the first ideas of what kind of gate it should be.
You have to know that the church is a very beautiful church.
The church is protected by a monument.
And I'm not allowed to try to incorporate my personal note
into a gate or a grid.
Instead, I add a masterpiece of the early days
and try to reduce it, to work as conservatively as possible
in order to show that a new grid has been created
that meets its needs,
but has nothing to do with the history of the church.
The next edge is 80.
In the end, only the base of the column has to be measured,
because it is wider than the arch above it.
75.
That's why the gate has to be narrower at this point later.
In the forge in Höheischweiler near Pirmasenz.
This is where Thomas Maria Schmidt works.
After the measurements in the church,
he transfers the measurement results to the computer.
Accuracy is important.
The forger recognizes that those who built the church
did not take it very precisely.
You can see from the precise transmission of the measurements on the computer
that there are also irregularities in the tip arc.
It used to be like that.
You didn't focus on 2-3 cm,
but you said that the overall picture at the end should be the composition,
should be correct.
And that is also very correct.
And these points, these small irregularities,
sometimes from 5 to 10 mm,
we have to compensate for that.
After the measurement results have been entered,
it goes to the drawings.
And the question of what the gate should look like.
I thought about the gate, of course,
and I also created a concept.
I had a task.
The task was to make a gate.
A gate means that it should separate the church space
so that unauthorized people cannot enter the church,
but can look inside.
And that's why I came up with a clear layout,
as it is in the Neocatholic church.
It is on the walls.
These are the windows.
You have practically the horizontal lines.
You have the columns.
These are the vertical lines.
And to create a necessity for a gate,
reduced to really the most necessary,
is vertical,
to block the room,
or to block the passage,
and the horizontal lines,
that is the support of the vertical lines.
That is reduced.
Of course, I could build something like that with snorkels and so on,
but then the clarity of the line would disappear.
These are the rough features of the gate.
But there are also important details.
A cross in the middle, for example,
and a special decoration at the end of each gate post.
My highlight in this gilding, so to speak,
would be the tips, the tips of the gilding.
They are supposed to represent a bud.
The bud is the beginning of a life
and should look like a flame, a candle.
That means eternal life in the sacred space.
The next day, the building steel is delivered to the forge.
It comes from the region
and is tailored to the needs for the gate construction.
Well-chosen 300 kilograms of steel.
Material price around 500 euros.
Downwards!
There are two criteria for the material.
The first is the claim to stability, the static is to be considered.
And the second, which is also important,
there is a teaching of proportions of materials.
You can't just make, for example, 40, 50 posts
and fill rods out of 10 round irons.
That bites the eye.
So you have to adhere to these proportions
so that there is a coherent picture at the end.
Round iron, thicker, narrower rods,
angular rods.
The entire gate is to be built from them later.
But what properties does the steel have to meet?
When you start building welding constructions,
you need special steels.
There are now 1,500 to 2,000 different steels
that are being processed.
This is actually the Waldwiesen steel,
which meets our requirements for gates, grids.
It is important, first of all, that there are no sagging,
that is, for non-cleaning.
Second, that the carbon content is correct,
because the weldability and forgeability
are very dependent on the carbon content.
These are actually the decisive points
that we need for our steel.
Then it goes into the forge.
Now the material can be worked on.
But before it goes to the actual forging,
the sketch of the gate has to be drawn on the workbench.
And very precisely.
First the silhouette of the gate,
more precisely, a gate arch.
When I'm done with the silhouette,
which represents the outer frame,
I will then do my gluing.
This is the horizontal and vertical gluing.
First I will draw a vertical rod, a grid rod,
shift it, pay attention to the proportions,
that it is balanced.
And then draw the cross rod,
the holding rod of the vertical rod.
And you would have to draw little things.
For example, we have a cross in the middle of the gate.
We have buds, which I then try to draw one by one.
But why draw everything again?
There is already a precise sketch.
Drawing on the workbench is an old craft,
and that's why it's important
that you can check a one-to-one drawing.
You look for a position, for example on a ladder,
and look at the final drawing on a one-to-one scale
and check again its proportions,
whether it is bright and whether the gluing is correct.
What is important when drawing,
you should take your time,
you should not underestimate the drawing
and smear it on the table or on a piece of paper in 10 minutes.
Paper is patient.
In the end, nothing is right.
So the control before I start cutting material,
determining material,
the A and O is the one-to-one drawing.
After a few hours of work,
now comes a tricky part,
the upper part of the gate,
the arc that was measured with the laser.
It is known to be crooked.
That is precisely why nothing can go wrong
when transferring the measuring values.
We have already drawn half of the gate,
a gate wing.
Now it's about
fixing the upper end of the gate wing.
Now I fix the points
that we measured in the church.
These are the individual layers
that we measured from the arc.
And now I have a middle axis,
the middle axis of a wing of the gate.
And next to a measure,
I mark them with these points.
And when I connect these points together,
we have exactly the tip of the church on the workbench.
First the rough raster,
now comes the detail work.
The knobs are drawn
according to a sketch and a prototype.
The cross is also drawn.
On each of the two gate wings
one half of the cross should sit,
the end of the gate.
Finally, the drawing is finished.
Now is the point where I take a ladder,
choose a high spot
and look at the drawing,
let it affect me
and possibly change my gut feelings.
You say, yes,
you could move that a little bit.
The gate wing from above,
three meters high and 1.20 meters wide,
it should be analogous to the second wing.
All in all, I am very satisfied.
I like the layout very much.
When we cut and lay the material,
we see a little more.
But when the material is forged
and the crossbars are inserted during the assembly,
then you see that the child comes into the world
and then you really see what has grown out of it.
The last step before the actual forging.
Your task is to cut these crossbars
from the material 30 x 20,
as I have already written,
and the length 1.10 meters.
The supplied construction steel is cut.
Stephen helps,
the other son of Thomas Maria Schmidt.
Everything must be brought to the right length before forging.
It is noticeable
that such a gate is made of quite a few parts.
We have to cut the individual parts for the whole gate.
This starts with the crossbars,
the vertical bars,
the hinge parts,
the round iron that holds the knobs.
It goes over the frame.
It's all individual parts.
I have to count,
but I estimate that per gate wing
there are about 100 individual parts.
Again, many hours of work.
After the cut,
the sharp edges are sanded smooth.
Then Thomas Maria Schmidt
puts all the parts on the workbench,
on the drawing.
In this way, he first gets an impression
of what the gate will look like later.
I'm going to cut now.
78 centimeters.
Now we have cut the parts,
which are necessary for a gate wing.
The other parts we have cut in parallel
and put aside.
What do you see now?
Now you can see the basic structure
of the gate wing.
You can see the proportions,
the square flat iron
playing with the round iron,
the round iron playing with the ball,
which later gives the knobs.
You can already see the beginning
of the composition of the song,
of the piece that we produce.
In the end, it's a vocal part.
Now comes the main part,
which is actually the blacksmith.
The blacksmith will take some time,
because blacksmithing is still a manual work,
at least for us,
and in the end the gate lives from it
through its manual work,
through its blacksmithing.
That's where it starts now.
The coal is heated
to 1400 degrees Celsius.
First, the so-called holes are forged.
They are important for riveting,
i.e. for connecting the individual parts together.
They are also important for the hinges.
This is a difficult task,
because it's about millimeter accuracy.
Drilling such holes
is a level of difficulty
on a scale of 1 to 10,
at least at 8 or 9.
But there are even more difficulties
when forging these holes.
The difficulty lies in the fact
that you have to start the hole
from two sides.
You start by cutting the material from above
and turn it and cut from below.
And then the accuracy of the cutting
is what creates a degree in the middle.
This means that if I hit the hole chisel
exactly on the other side
with my chisel,
that's the difficulty.
If you don't hit it together,
the hole will be crooked
and you can't save it,
you can throw it away.
In other words,
you have to have a lot of experience
to be able to hit the right spot.
And there are other reasons
why the forging of holes,
i.e. the holes,
is a great craftsmanship.
When I take a drill and drill a hole,
I cut material out
and leave the surrounding material
of the hole alone.
Nothing happens.
If I make a hole
through a drill,
a split and a drill,
I move the whole material,
I don't take material away,
but a hole is created.
Where does the material go?
It pushes out in all directions,
so it shifts the holes.
It takes five minutes
to forge such a hole.
About 120 of these holes
have to be made,
60 for each gate wing.
After a whole day of work,
the holes for the hinges
and the various brackets
are largely finished.
You could just do it
like we actually work today,
that you cut a rod,
take the welding machine
and weld it together.
But that's not craftsmanship.
We want to represent our craftsmanship,
we want to represent our pride.
That means we want to build a gate
that also has the class
of being able to be built
in a church like Konzig.
It should be seen
as a craftsmanship gate
and not a hardware store gate.
It's fun to work
when you see the result
and see such great holes
that it worked so wonderfully
with such a wonderful stopper,
which is very important.
The half-width is the stopper
and I'm proud
that it worked so well.
But the forging of the hole
is not yet finished.
The holes are also visually shaped
and aligned as hinges
and brackets.
After the holes
the brackets are made
and that is very small-scale.
It all starts
with a spreader
of long round irons,
which will later be used
to make the longitudinal rods of the gate.
We stuff one end of the rod.
That means it is heated
in a forge fire
and then stuffed
on the metal floor plate
to spread the end pieces
and increase the cross-section
to create a basis
for the stopper.
The reason is
that the stopper sits on top
on the stuffed end
of the longitudinal rod
like a flower
that sits on a stem.
Forging is hard work,
although the steel,
at least in hot condition,
is fortunately rather soft.
In the fire
we get a doughy state
of the steel
and can actually shape it
like a baker's cake,
his pretzels.
We can poke, stuff, push, punch.
After about three minutes
a stuffing is finished.
In the end
16 have to be made
because on each wing of the gate
there are eight of these longitudinal rods
with the studs.
The next step would be
to clamp the rod
on the workbench
and drill a 12 mm hole
in the middle of the front side.
This 12 mm hole
has a depth of about
15 to 20 mm.
The holes have to be
very precise.
The studs come later
and they have to sit precisely.
Next, steel balls
have to be welded on rods.
The studs have to be forged
from the balls.
In this case, the rods
only serve to hold the balls
in the hot forge fire.
When the studs
are made later,
the brackets are cut off again.
Then it starts
with forging the studs.
The ball on the rod
comes into the forge fire
and is heated to forge temperature
between 800 and 1200 degrees.
It is then forged
chronically under the air hammer.
This means
that it gets its
conical shape.
Chronically means
that it is forged from a thick,
wider cross-section
to a pointed tip.
But the air hammer
does not do all the work.
The shaping of round studs
is part of the high art of forging.
The ball is shaped
into a knob.
It requires a bit of skill
and skill.
16 of these knobs
are needed by Thomas Maria Schmidt
for his two gate wings.
After forging,
the knobs are separated
from the rods,
i.e. sawed off.
Below the knob
is a shaft,
which is exactly the length
and diameter
that it fits perfectly
into the holes
that Thomas Maria Schmidt
and his sons
initially drilled
into the stuffed round rods.
The knobs are placed
on their rods
and, in turn,
later become the length rods
of the gate.
However, the knobs
still have to be attached
to the rods.
For this, hard lead is filled
into the rods.
Then the whole thing
is heated with a burner
to 800 ° C.
Then the lead becomes liquid
and the knob slides
gently into the hole.
At the shaft of the knob
a so-called capillary effect
occurs.
The lead pulls up
on the flanks,
connects both the shaft
and the lead.
Then you have the result
from the ball,
the knob forged.
With the rod,
one unit is one lance,
one vertical joint
of our gate.
But that's not all.
The knobs on the length rods
are finished,
but the rods also have to be
brought to length.
In the end, they have to be
up to three meters long,
because that's how high
the gate is.
To achieve this length,
the rods are welded
to other rods with the knobs.
Now comes the highlight.
The cross is forged.
A central view of the gate.
Since it's a
ornament-free gate,
I wanted to put
an ornamental element on it.
It's close to the church,
like the cross.
I started to think
about putting a cross
in the center of the gate,
the symbol of Christianity.
Forging the cross
takes a good hour.
The steel has to be
put into the fire
so that it's hot enough
to be forged.
The important step
is the bending process
in the current state.
First at 90 degrees,
then at 180 degrees.
At the 180-degree bend
a beautiful wool is formed.
I'd like to keep this wool
or forge it out a little
and embellish it.
The intensive processing
of the 1.5 meter long steel rod
is hard work
for Thomas Maria Schmidt
and his son Steven.
A lot of work in the forge
can only be done in pairs.
This is craftsmanship
in the truest sense of the word,
unlike in many other places
in modern times.
It's complicated,
but nowadays
iron is cut to size.
The computer programs
are already set up.
I insert a railing, a gate, a grid
and I get the finished lengths
to cut and weld together.
But that's not craftsmanship for me.
The cross for the gate
consists of two halves.
That makes it even more demanding.
I make it out of two parts
because it stands on two
gate wings.
And then I will
adjust one cross
to the other cross
by laying it down.
The difficulty with the cross
is the alignment.
The two parts are mirrored
and you have to lay them down
and shape them
to make a small difference
even if it's 5 or 10 millimeters.
Otherwise the whole cross
would look a bit strange
And the alignment is difficult.
Controls again and again.
In the end, the hand press
is used.
The lower part of the cross
has to be bent
so that it can be better
attached to the gate.
The boss is satisfied
and remains modest.
What you see on the cross
makes it nice for me.
It's fun to work with
little work, but you get
nice effects.
After the cross,
it's time for the castle.
To be more precise,
the two locks for the gate.
Filigree technology is required here.
A task for Thomas Maria Schmid's
son Daniel.
I had Daniel do the lock
because he is our fine motorist
who I would say is married
to the mason.
He can work precisely.
And to design the castle itself,
we sat down and thought about
what we would do, how we would do it.
He then built it up,
marked it on the workbench
and then worked it out.
The two have also developed
the locking mechanism.
It is the heart of the castle.
And for this locking mechanism
a suitable cylinder lock
is necessary.
This, on the other hand,
has to be in a suitable format
that is elaborately drilled,
sawed and filed.
As long as
the cylinder lock fits in
and sits perfectly.
However, the format
for the cylinder lock is only part of the work.
The construction of a castle
takes several hours.
Most of it is self-made.
To build a castle for this gate
is actually quite
complicated work.
Because such locks
as finishing modules
are not available for purchase.
What we can buy for it
is a profile cylinder,
which is in every house door,
which also gives security
when closing.
Our task is to make the gate
lockable, to provide the gate
with a lock, a lock,
which also fits optically to this gate.
I can't just buy a normal handle
or a lock
and install it.
That would not be
optically sound.
And this is the bar,
which later comes into the lockbox
and together with the cylinder lock
forms the locking mechanism.
As elaborate as the locks are built,
future break-ins will probably
have a hard time
getting into the church without permission.
It is not unusual
that a blacksmith in such special cases
as this one also perceives
the work of a locksmith.
Everything else would be even more elaborate.
After many hours of work
the two locks are finished.
Only at the very end,
when the gate is completely assembled,
the lock is inserted into the gate.
The assembly is the next point.
And that takes time.
More than one working day
is needed to put all parts
on the workbench,
on the drawing,
connected and aligned.
That is the goal.
Aligning is very important,
because if I had a grid gate
with a lot of wrinkles,
no one would see
if somewhere 5 mm
or 1 cm or 1.5 cm
would be missing.
And with this
well-aligned
line, division,
it is important,
because everyone can see
if some angles are wrong,
if the parallelism is wrong,
and so on.
And when assembling,
you quickly notice
if something does not fit exactly,
like here.
Then it has to be done
appropriately.
We have 120 holes
and if one of the 120 holes
is shifted by 2 mm
or 3 mm,
like in this case,
it is artificial.
But there are possibilities.
We drill a little bit,
make the hole a little bigger
and then it fits.
So that's quite normal.
Gradually, the gate wing
takes shape.
So that everything is accurate
and can be properly attached,
all parts are attached
with large clamps on the workbench.
Then it goes
to the final assembly.
We have aligned the frame
in the right angle,
have created the parallelism
of the lower joint,
have created the vertical left outside
and have thus practically
fixed the frame.
Now the rods come in,
the vertical rods into the frame
and that these rods
no longer slip, they are also fixed
with a welding seam at a point
where you no longer see it later.
Then everything fits.
But even when welding,
something can still go wrong.
Everything is much more difficult
than it already looks.
You should take your time,
because it's not easy.
It also requires a lot of experience,
because even when welding,
a delay occurs,
where there is a thermal impact,
a delay always occurs.
If I were to weld all the rods
right, right, right, right,
the whole grid would move.
That's why you need a welding sequence.
You have to weld right, left, left, right.
When the framework of the gate
is ready, the hinges come in.
They have to be retracted
and screwed.
At these points,
the two gate wings are anchored
in the wall of the church.
They have to hold a weight
of 110 kg per gate wing later.
Then,
after almost three days of assembly,
the two finished gate wings
are first laid next to each other
to see if everything is right.
And the master likes it.
The gate is now here
and I am very satisfied.
There are still a few little things
to do before we load it up
and go to the assembly.
I like the composition.
It's done.
The clear joinery is done.
The craftsmanship is done.
I would say
the welding was worth it.
But before
the installation,
the castle that Daniel's son built
has to be checked.
The castle box,
which has already been screwed on,
is opened again.
The big question is,
does the castle grip
smoothly in both gate wings?
And?
Yes, it fits.
The cross in the middle
also looks symmetrical.
The next day,
the gate wings are loaded.
Almost no problem for the three of us.
Loaded.
The welding is done.
Now it goes to the construction site
for the final assembly.
We hope that the final assembly
will run as smoothly
as the construction of the gate.
Then we will have
a nice evening
and can look forward
to the new gate in the church.
Let's go to Condwig.
The Catholic church
is about 20 minutes away.
The construction of the two gate wings
took two weeks in total.
The installation takes
a whole working day again.
And that's not easy either.
Here, too,
the laser is used again,
but this time not to measure.
We are looking for a lathe
to install the individual
gate wings.
Because the gate wings
have to fit together
in the lathe.
And if I rely on the columns
of the church,
which are an old building material,
then I am mostly left out.
Control is important.
Pull a lathe,
align the gate wings
so that they close in the middle
so that they do not jam.
But it is not only important
that the gate wings fit together
They also have to be
attached to both sides
at the same height.
That means that the holes
also have to be drilled.
Only then does the symmetry remain.
The brackets and hinges
of the gate wings
should not go wrong.
When drilling holes,
you have to be careful.
We must not drill wrong.
We have everything
measured and aligned
with our laser.
Actually, it is
dangerous if you drill wrong.
If it should happen,
then the emergency plan
would take effect.
That means we have another craftsman,
Steinmetz.
Steinmetz would have to
close the hole again.
They have techniques.
They can close holes
so that they are no longer
visible at the end.
That would not be a problem.
But we'd rather not do that.
Until now,
everything has worked.
Next, the special glue
comes into the hole.
It becomes stone hard
within a few minutes.
So it has to be done
very quickly.
Glue and the brackets
of the gates.
The glue is so strong
that it can hold a heavy gate
effortlessly.
It only takes half an hour
to harden.
Then the gate wings
can be screwed on.
For the first time,
Father Johannes Müller
is with us.
Thomas-Maria Schmidt
gives everything.
It's a gate
where everyone thinks it's a simple gate.
It's not much.
A few sticks are built together.
The composition of the gate,
the golden cut,
the symmetry of the cross and
the longitudinal links,
that's important.
If you measure,
you see that the lower distance
is not the same as the middle
and the upper distance.
But it all makes sense.
It all plays a part
in the harmony of the gate.
One, two, fits great.
We're already in progress.
But we still have
the possibility
to adjust the wings.
We can still adjust the individual wings
to compensate
for any difficulties
later when closing.
And the priest,
how does he find his gate?
It's not just
a functional fence
where you can't get any further.
There's a slender
decoration on it,
which fits this new Gothic.
This elongated,
leading to the top,
and that comes
very nicely to the expression
in this gate.
I really think it's great.
Yes, it's really successful.
You don't even imagine
if you've never had
anything to do with metal
how it works.
It just seems to be there
and I'm really satisfied
and I'm sure everyone else
will be too.
The castle also works
and fits exactly.
So everything is done right
when drilling.
Later, the sides
next to the gate have to be
attached so that the church
is actually protected
from burglars and thieves.
But that's only the next step.
Most of the work was the gate
and Thomas Maria Schmidt
also likes it.
It took me two or three minutes
to take a look at the
harmony of the gate
and how it fits into the church.
I'm actually more than
satisfied, I have to say.
I have a very clear
link and this link
also plays with the ribcage
in the church.
First of all,
it's a barrier,
a passage barrier
that you can't enter,
but still it's not a prison.
It's something open,
it's something uplifting,
it's something gothic.
It has life
in the buds,
it has the symbolism of our religion
in the cross, and that was important to me.
And the harmony of the proportions
of the cross, of the
vagrant joints, I'm satisfied.
The gate is finished,
it just needs to be painted.
Craftsmanship
of the finest.
Thomas Maria Schmidt shows
that blacksmithing is still
a demanded, valuable craft.
He sees for himself
and his sons a good chance
to preserve the tradition,
a tradition with a future.
I explained to him,
even if the money is devalued,
if bankers
and so on
realize that their notes,
on which numbers are written, are worthless.
You always have your hands,
that's your money, with those hands
you can create something.
You can make a nail for everyone
and you can live from it.
