How to make a Wooden Katana from hardwood flooring // Woodworking | I Like To Make Stuff

I Like To Make Stuff
23 followers
5 Video Views·Feb 1, 2023
Hey, I'm Bob and I like to make stuff.
Today I'm going to use hardwood flooring to make a katana.
Ever since we watched Iron Fist on Netflix,
I've been wanting to make a practice katana.
And then watching Alex Steele make an actual, real katana recently
really pushed me over the edge.
I don't know anything about swords, and I don't speak Japanese,
so I'm not going to call these parts the right names or anything like that.
This is really just for fun.
And to make it even more fun, I'm going to make the whole thing out
of hardwood flooring.
While we were looking for hardwood flooring for our house,
we ended up with a bunch of different samples
of different species of wood.
I'm going to use these for different parts of the sword.
I'm going to use this one for the blade guard, these for the handle,
and then what we actually bought for the house,
I'm going to use for the blade and for some fancy inlays.
All right, let's get to it.
I only did a tiny bit of research on katana,
but I did find a reference to the length of the handle.
Usually it's about the same length as your forearm.
I made some reference marks for that, and then I
used some pinstriping masking tape to lay out the shape of the blade.
It's pretty thin, so it makes it really easy
to get a nice, consistent curve.
I went back with the measuring tape to make sure
that the blade was about the same thickness from top to bottom.
I used a bandsaw to cut this out, cutting on the outside of the tape
to make sure that I had plenty of material to cut down later.
If you don't have a bandsaw, you could also use a jigsaw for this.
It would just be a little bit more work.
I cut on the inside of the tape for the shape of the tang.
Most of the flooring that I had was 3 quarters
of an inch thick, which is, of course, way too thick for a blade of a sword.
So I drew a line down the length of the blade
and then set up the table saw to resaw it down to the right width.
When I cut out the outline of the blade,
I tried really hard to stay right on the outside of the tape,
but I didn't get it perfectly smooth.
So I used sanders to get it a nice, even curve from end to end.
If you were working a blade in steel, you would use a grinder much the same way.
This is a good way to get a nice, consistent curve
before adding the bevel on the table saw.
To safely add the bevel to the end of the sword, I used a sander.
But this time, I used my belt grinder instead,
because the sandpaper is a smaller area and it had a little bit more control.
I went back and forth from side to side, sanding it down
to try to get an even bevel right in the middle of the blade.
Also, because it's a thin piece of sandpaper,
I could make micro adjustments to the back to any areas
that were flat or needed to be evened out.
And finally, I used an orbital sander to remove the original finish
from the top side of the wood.
This makes the entire thing raw wood and ready for even finish later.
The tang was still as thick as the thickest part of the blade,
and I needed that to be thinner so that it
would fit on the inside of the handle.
So I used the table saw and the bandsaw to trim it down,
trying to make it even from side to side.
Getting an even cut on both sides of this was actually
a little bit harder than I expected, and I had to do quite a bit of trimming
and then come back with a chisel to even it up.
The outside cuts of my tang were not perfectly straight and parallel.
And since this was going to go inside the handle later,
I decided to use the sander to flatten them out.
And after those were down to size, I used a chisel
to square up the corners in between the blade and the tang.
This will make sure that it's a nice snug fit when
it goes into the suba, or the hand guard.
To make that piece, I used some calipers
to figure out the outside dimensions of my tang
and then mark those onto another piece of hardwood.
I just connected those dots with a pencil
so I had a reference point, making sure to only cut away
material on the inside of that box.
I used the drill press to hog out most of it,
and then went to the tedious work of actually clearing it out
and making it the right size.
Most of this was done with the Dremel, being really, really careful
to just go up and down and not drag it along the face.
But then eventually, I had to move past that to use a file.
The first thing I really did with the file
was trying to square off the corners to make sure that it would fit at all.
Once I got it squared off, I could get the end of the tang in place.
Then it was a matter of clearing out more material.
I went ahead and ran it through the table saw
to thin down the overall material so there was actually a lot less to sand.
This was trial and error, and every few minutes,
I got the tang to go in a little bit further and a little bit further.
And eventually, there was a really nice fit.
I traced the outline of the blade, and this was actually really important
because I needed to be able to find the center line of where the blade set
in relation to that piece of wood.
I drew a center line along those two marks
and then printed out a template of an oval that was the outside shape.
I put a center line in the template and lined it up with the marks
that I'd made so I knew the hole was right in the correct position.
I cut this piece out on the bandsaw, staying on the outside of the line
but trying to get as close as I could.
A disc sander is great for being able to sand right up to the line
and get a nice even curve.
I also used the sander to flatten out the cut side of this wood
to make sure that it was perfectly flat.
But it has such a heavy grit that I used an orbital sander
with a higher grit paper to smooth it out and get rid of any burn marks.
I did some test fits to make sure that it was right in place,
and it was starting to actually look like a sword.
Next, it was time to make the handles.
I used two different types of wood for this,
and I re-sawed them on the table saw to get them about the right thickness.
Josh has been helping me out in the shop, and he ran the CNC work for this,
making an inlay pattern.
He used the inlay generator in the program Easel
to make some pockets and some diamonds to fit inside them.
When we made the handle pieces, we also had the CNC score in the outline
of each handle piece so that the pockets were perfectly centered
when we cut the pieces out on the saw.
When you cut pieces out on the CNC, one of the problems is that
once they become loose, they fly all over the place.
So for the diamonds, we didn't cut all the way through the piece of wood
and left just a little bit on the backside.
I laid some blue tape across the front to hold all of those pieces
and then sanded off that thin layer on the backside.
This makes it nice and easy to get all the pieces out
without having to cut out tabs on each one.
I sanded off the outside edge of these and then added lots and lots of glue
to all the pockets before pressing each one of these in place.
After the glue dried on these, it was time to cut them out to their final shape.
The lines came in really handy here to line up with the saw blade
to cut each one of them out.
We intentionally left the diamonds a little bit proud of the surface
so I could use a belt sander to flatten them out
and remove all the glue squeeze out.
This actually was a little bit harder because of the type of wood,
so eventually I just ran it through the table saw
and got rid of anything that was hanging over the front face.
I set one of the handle pieces in place all the way up against the suba
and clamped it on.
It really needed to stay right in place so I could mark its placement
on the bottom of the suba and then use a marking knife
to mark the outside of the tang.
I took that one off and used the markings I'd made
When I make these projects, I intentionally don't go around
and look at other people's videos to see how they did things
so that I don't accidentally steal somebody else's ideas.
Well, last night, YouTube recommended a video to me on making a wooden katana.
I broke down and watched it, and it's from a guy named Geeks Woodshop,
and it's a great video.
And although we are doing a lot of similar things, including the handles,
he does some things I didn't even think of.
He does a really cool effect on the blade,
and you should definitely check it out.
I'll link it down in the description.
So if you like this project, be sure to go watch his.
With the inside of both pieces of the handle ready to cut out,
I used some double-sided tape to hold these pieces down to the table.
I set the depth of my router to half the thickness of the tang
so that it would only be halfway into each handle.
This took a little while, but I plunged out all of the area
on both of the handle pieces.
I stayed well on the inside of the lines
so that I could go back and clean up those lines with the chisel.
Just like with the suba before, I wanted this to be a really tight fit,
so it was a lot of very small changes and trial and error.
I laid the tang in place and found the places where it overlapped
the handle piece, marked those so I knew exactly where to cut away.
Eventually, I got a really snug fit on both sides.
Once I got the tang to fit into both sides of the handle,
I pulled both of those pieces off the table and fit them together.
The next step was to put the tang in between them,
and by doing this, I found that it actually wasn't halfway in
on either one of these.
There was a little bit of area that needed to be cut away
because of inconsistencies in the thickness of the tang itself.
After I got that cleared up, I used a router to add a roundover
to the outside edges of the handle.
My router always adds a little bit of burning, too,
so an orbital sander got rid of that pretty quickly.
The more I sanded these pieces, though, I found that there were
some small gaps from the CNC inlay that didn't quite get filled in.
To fill those in, I used the sawdust from the sander and some CA glue.
This isn't a perfect solution, but it makes it better than just having a gap there.
By using the same sawdust, it's generally the same color as the wood that you're filling.
Once that dried and I got it sanded down,
eventually the handles were just about ready to put on.
My plan was to add a kashira, or a cap, to the end of the handle,
and to do that, I had to line up the handle pieces using the top face as a reference,
taping them together, and then cutting a flat edge on the bottom with the miter saw.
Then it was finally time for the glue-up.
I added lots of glue to all of the surfaces that were going to be attached,
inside the handle, all the way to the edge,
to make sure that everything was glued together and there were as few gaps as possible.
With everything lined up and glued, I just added lots of clamps.
And since I wanted to minimize the amount of sanding I would have to do on the handle later,
I used a wet rag to wipe off all the glue squeeze-out that I could get.
Then it was time to make the cap with the kashira that went on the end of this.
I used a small piece of hickory flooring for this,
and cut out a shape that was generally like the shape of the handle.
I also used the sander to remove the relief kerfs on the bottom
that most pieces of hardwood flooring have.
I found the center of the bottom of the handle and drilled a hole
that matched up with the size of a wooden dowel that I had,
then I found the centerpiece of my kashira and drilled a matching hole.
I used lots of glue to knock these pieces together,
glue all of the surfaces, before putting the cap into the bottom of the handle.
You'll notice here too that I left the kashira bigger than the handle
so that I could shape it down to match later on.
And of course I added a couple more clamps to hold this in place while the glue dried.
The disc sander made it really easy to make this piece down to the same size as the handle.
I just used the handle as the reference, making sure not to sand any off of it as well.
Eventually I used a sander to roughly round over the corners
before clamping it to the table and using an orbital sander to really smooth it out and shape it.
Now the only piece of this sword that's not made out of hardwood flooring
is a piece called the hibaki and I made it out of bamboo veneer.
I cut two pieces, soaked them in water so they were a little flexible,
and then clamped them around the blade and let them dry.
After they dry in this position they hold the shape just enough
so they won't crack when I glue them on.
For these pieces I used CA glue and activator so they would quickly set in place
and I could keep moving.
This was a little bit messy and I wasn't super happy with the results.
I'll think a little bit more practice with the veneer,
getting it cut and shaped to fill all the gaps would make it look that much better.
I intentionally left these pieces a little bit proud as well so I had plenty of area to sand down.
I wanted all of the corners to be smooth.
I used a sanding block to round over the rough edges and try to join up these pieces as well
as I could and eventually used a popsicle stick wrapped in sandpaper to get fine adjustments.
After that it was all done and ready for finish.
And for this I used a mixture of beeswax and linseed oil.
We tested out several different finishes with this
and this combination brought out the color in the woods better than anything else.
It does stay oily for a little bit so you have to let it soak in for about 24 hours
before you want to handle it.
Check this thing out, I'm super happy with how it turned out.
Of course there are some little issues with it and problems and stuff
but I learned a whole lot putting this thing together and I love the way it looks.
It's super cool that this was made out of just flooring
and I think anybody can get access to some scrap pieces of flooring
to make something like this if you want.
I found a chart online that talked about the length of the sword blade based on your height
and according to that chart this one's about six inches too long for me
but I just love the fact that it's such a long sword.
Let me know what you think about this video down in the comments
and don't forget to go check out both the video by Geeks Woodshop
and the series by Alex Steele all about katana.
I've got lots and lots of other videos that you may be interested in.
I'll have some of those right here and don't forget to subscribe.
That's it for this one guys, thanks for watching.
I'll see you next time.
