White Resin Serving Board—DIY Charcuterie Boards—How to Woodworking

Blacktail Studio
97 followers
6 Video Views·Jan 9, 2023
Hey this is Cam with Blackdale Studio and today I'm going to show you how I did these DIY
resin serving boards. I really liked this project because it didn't cost me anything.
These were some walnut burl slices I had laying around along with this walnut slab
and I turned them into this white epoxy resin serving boards that I was pretty happy with how
they turned out. So here's the process. I started off with my crosscut sled here. I usually prefer
this to the miter saw if I can help it and I was just roughing these out to get them approximately
the same size. If you don't have a jointer you can actually make a little jointer jig for your
table saw but since I have one I'm going to run it through a couple times just to get one good
clean straight edge and now I can take it over to my table saw to get it to the size that I wanted
since this slab was a little bigger than I wanted it to be. Also dirt is much worse on your blades
than wood so I try to get all the dirt off before I run it through my planer. If you're curious about
these quick clamps I'm using I made each one cost me about five bucks a piece which is a little
cheaper than the $40 Festool ones. I'll include a link above if you want to see how I made those.
And once it's clamped down I can clean up the edge with my porter cable restorer and the nylon wheel.
If you've watched any of my other river table builds the form building is essentially exactly
the same only this one's going to be a little bit easier. I just cut I believe there are two
inch strips for the sides, assembled them, and I didn't use any nails or screws. I just used this
fast dry caulk to assemble it all and that way it would come apart a little bit easier.
I like to use this type of mold release when I can. I've also used the spray stuff but that
stuff stays airborne for so long that I'm a little worried about it contaminating the wood or getting
on other objects. So this stuff you just brush on it's kind of expensive but it goes on very nice
and releases very easily. You heard me say at the start that this project didn't cost me anything
which isn't entirely true. I was making a larger round resin table that I'll include a link to
also and I always make a little bit more than I need and so for this one I was planning on using
these serving boards as the overflow. Anyway I'm using a polymer technologies chill 2 epoxy. It's
a great super hard curing epoxy and this is eco epoxy liquid dye just the regular white and here's
the bigger table that I'm building simultaneously but after I've topped that off I'm going to use
the rest to fill in for these serving boards. You'll see I did the painter's tape on the 2x4s
here to keep these from floating. I've since discovered a better way is using packing tape
and then putting a little bit of that mold release on the packing tape on the 2x4 pieces
so that way they'll just come right off and you'll see the problem here shortly with the painter's
tape. The sides came off pretty easily it's actually just the caulk holding them on the
epoxy doesn't stick at all with that mold release on there. Driving some wedges in don't want to
break the epoxy so trying to go pretty evenly you can see that bottom came right off and that's
because of the mold release. I hit these pretty good with the mount and they would not come so I
ended up having to cut the 2x4 completely off which obviously isn't ideal and these obviously
aren't too big to go through my planner but I was taking five or six projects into creative
woodworking in Portland so I figured I might as well dull their blades instead of dulling my blades.
Once I got these back home I just had to square them up on the table saw
and then I decided to put a couple small bevels on there just for looks.
I went with a 22 degree bevel here not for any particular reason just thought it looked a little
more interesting than a 45 and if you follow my videos with any regularity you've probably
seen this tool already it's the Festool vacuum clamp. For projects like this I absolutely love
it, it doesn't leave any marks. If you clamp this down to a table you always run the risk of damaging
the wood or imprinting the wood and this rotates, tilts, makes it really really easy to sand.
I got a Festool sander too and what I did is I took these up to 400 grit and the finish I'm
going to use allows to go that high and it gives a really nice natural sheen without getting too
polished. Even though these are just a side project definitely take your time run through
all the grits properly 100 grit, 120, 150, 180, 220, 320, 400. Now that you're ready to finish I'm using
Odie's oil and the reason I'm using this specifically on this one is it's the best food safe finish I've
found. You can apply several coats if you want to really step the sheen up and you just buff it in
with one of these non-woven pads people also call them a scotch-ripe pad but you can get these at a
woodworking store probably even Home Depot. Just kind of buff it in fairly aggressively you don't
want to scratch it up too much but they'll really help even out the sheen as you're buffing that in
and only use these terry towels to wipe it off but make sure you get every last bit of it off
you'll run into problems if you don't get all of it off. Odie's oil dries pretty fast you can use
it just a few hours afterwards but three weeks to full cure if you're going to really be spilling
a lot of hot coffee and things like that on it. Okay that's the whole project I'd love to hear
your thoughts on this project if you liked the white if you hated the white if you had any other
colors that you think would look a little better because like I said before this was essentially
a free project so most likely I'll be doing quite a few more of these types of projects in the future
and if you enjoyed this video please subscribe for more just like it. Thanks again!
