We're Jennie and Davis. We love watching people grow. That includes you! Join us as we learn to build a furniture business. We want to help people dominate their fears and weaknesses. You can learn from our mistakes ;)
Welcome back friends.
Today we are going to take your suggestions and build the best charcuterie board jig on
the internet.
We're Jenny and Davis.
We fly through hurricanes for research and build furniture for fun.
A while ago we came up with a business plan to sell quality furniture which brings people
together.
Follow along as we build our business empire.
Empire?
Yes.
Jenny.
Big goals.
Okay.
We're starting an empire.
Empire.
Maybe one day it'll span beyond the garage.
A few weeks ago we were building some charcuterie boards and we built this jig to help us get
the same exact handle on every single board.
We needed something a little bit faster than the traditional method of using like a template
that you stick to each and every workpiece.
So we built a little jig with toggle clamps on each side to hold the boards down as we
ran them through the router.
So if you want to go see that video, check it out right up here.
And in that video you guys gave us a lot of good suggestions of things we could do to
improve the jig even more.
So what were your suggestions?
Well, to the whiteboard.
So you guys suggested using a CNC or a laser to make the template so that our lines would
be perfectly straight and there wouldn't be any like jagged edges on any of the handles.
So we're going to see if our laser can cut through half inch plywood and if it can, cool
we've got our solution.
If not, we're going to cut out something a little bit thinner and then we can template
route that with half inch plywood.
And then the next suggestion was to index each board using a dowel.
Basically on our first jig iteration, we were spending a lot of time lining each board up,
finding center, figuring out where the handle needed to start and stop.
And using this method, we would be able to cut out a lot of that time spent like finding
the center because it'd be easily indexed in one place every single time.
And the last suggestion that was really good was to put adhesive backed sandpaper on the
base of the jig because when we were putting that rougher wood of the board on top of that
really smooth plywood base, it was kind of sliding around a lot.
So if we had a layer of sandpaper on the bottom of the jig, it would keep that board from
sliding around as much as it did.
So our first idea was to strengthen the toggle clamps on the jig itself.
We'll talk about that a little bit later in this video.
And our second idea was to make our tracing template bigger than the actual jig that's
cutting the board out on the router table.
Basically, one person is going to trace out the size of it.
And as long as it's larger, there's a little bit more play and room for error for the person
that's cutting them out on the bandsaw.
In our previous jig, we made them both the same size, and there's very little room for
error for the person that was cutting on the bandsaw.
All right, so we wanted to show you some before and after of the boards, but with the old
jig and with the new jig.
So we left off last time, we had a bunch of burn marks in the corner.
These are pretty deep.
They took a lot of hand sanding to get rid of.
So obviously we can't have that as part of our process.
Also the handle, there's kind of a bump on this side.
So we needed to improve those things.
And then after, it's a pretty considerable difference.
Way less burning.
Again, that was another suggestion you guys have, making this radius a little bit bigger
than the router bit's radius.
And so it really, really helped with the burning there.
Also slowed the router down quite a bit.
That helped.
But yeah, it looks way better and way cleaner.
Handle is perfectly straight and parallel, as opposed to this other one.
All right, so I'll shut up and show you how we built the jig.
Here's the jig and the tracing template.
Tracing template's just a little bit wider than the handle.
Then we put it on this jig right here, indexed again with the dowel.
Clamp the board down with these toggle clamps, which are up on these pieces of plywood.
So they're up off the bottom.
So theoretically, we have a limit to the size of charcuterie board we can make, which I
think is like 10 or 11 inches.
And the toggle clamps do a really good job of holding down the workpiece.
We didn't even need to put the adhesive back sandpaper on this jig.
When you use these toggle clamps, because of science, this pushes down, but it hinges
between these plywood layers.
So the strength of the glue bond here and the strength of the plywood layers is what
gives this its strength.
So theoretically, if you ever push down too hard on this, it would peel the plywood up.
So to counteract that, we've drilled screws through the bottom, tying everything together.
So hopefully, I won't ever have to worry about how tight this toggle clamp is pushing down
on one of the boards.
And there you have it.
And I'll see you in the next video.
Bye.
So we're building more charcuterie boards today because we basically got wiped out from
Christmas orders.
Our friends and family ordered way more boards than we thought we were going to have to supply,
which is awesome.
Thank you guys so much.
But now today, we definitely have to restock.
And while we were at it, we figured it was a good time to attack the second version of
this jig.
All right.
Well, this time, instead of 20, how many did we make last time?
20?
Instead of 20 this time, we made 22.
21 boards are done.
So thank you guys for your suggestions.
It really helps speed up the process.
So how well does this jig actually work?
We were able to build 21 boards in two and a half hours.
Two and a half hours.
That's it.
The last time we tried to build this many boards with the previous jig, it took us six
hours.
Six hours just to do 20.
That's an insane amount of improvement, all thanks to this jig.
And I know muscle memory might play a small role in it because we've done it a couple
times, but not as much of a role as this jig plays.
It really made a huge difference in our productivity.
So we want to thank you guys.
Thank you so much for all of your suggestions on our last video.
Each board has less burning.
They're more consistent and they're all around easier to build.
It's been kind of a long journey for us to get to the point where we have this sort of
product.
We made a hundred charcuterie boards like a year ago and they just weren't good enough.
We were kind of lying to ourselves and telling ourselves that they were good enough and that
they would sell and it's what people wanted, but they just weren't.
Not only that, but our procedure was so random and chaotic.
There really wasn't much consistency.
So not only did the boards not look very good, they weren't very easy to make and really
didn't fit in with our whole business model of scaling.
So now we have a great product with an even better process and in the future, if we want
to change the boards or slightly tweak the product, all we have to do is change up the
jig we're using.
So now we don't really even have to focus on product production.
So now we can focus all of our brainpower on selling and that's the important part.
We'll see you guys next week.