Sharpening broadheads can be simple and easy if we pay attention to detail. You can use sandpaper to sharpen your broadhead. A file can be used as well to sharpen your broadheads. Or you can use diamond stones to sharpen your broadheads. With any of these tools, you can get the sharpest broadheads. Woodsman broadheads are nice to sharpen because you can sharpen two sides at the same time!
Shop my complete tool list: Books, Archery Equipment, & Gear!
Hey guys, I'm so glad you're here today because today I'm going to show you how to properly
sharpen woodsman broadheads.
Trevor said he couldn't make it today because he said he's on vacation so it's just me today
so you're stuck with me but that's okay because I think you're going to get some benefit out
of these tips I have for you when sharpening your woodsman broadhead or any three blade
broadhead for that matter.
We got three woodsman broadheads here that are in really bad shape but today we're going
to get them razor razor sharp.
Now I'm not the best at sharpening in the world but I have learned a couple things here
and there and I think we can get these so sharp we'll have no problem during hunting
season.
One thing Patrick taught me from empty knives when I went to his shop is what sharp actually
means.
Most people think you have a sharp knife or a sharp tool when you are able to shave hair
and he said that's nothing like that's a dull knife.
What's actually sharp is if you can cut your hairs in half without touching your arm.
I was like what?
So that is the level of sharpness we're shooting for today but tools you use are far less important
than how good you are at sharpening.
You could use little diamond stones, you can use sandpaper, you could use bigger diamond
stones.
It doesn't matter nearly as much of what kind of tools you're going to use as it does how
meticulous you are at getting the blade really sharp.
If you have the right tools it will go faster but without the right tools you can pretty
much use anything around the house.
A rock you know a stone will sharpen something.
I could probably even use this lamp base here and if I rub it long enough I'll probably
get it sharp.
So don't worry about the tools as much as focusing on actually getting the broadhead
sharp.
The basic idea when you sharpen anything is that you have your blade right there.
Blade point.
And the goal is to take off material until it rolls the tip over this way.
That's where you get the bevel on the other side.
And then you're going to take material off this edge of the blade to roll material back
and what you're doing is you're rolling it back and forth making it thinner and thinner
and thinner until that comes to an extremely thin point and that is what makes razor sharp
blade.
So we're rolling this end over, rolling this end over but if you sharpen one side and switch
one side, switch one side without making an actual bevel you're not going to be making
near as much progress on a blade.
Another tip he gave me is in order to feel bevels it's a lot easier if your hand is wet.
So just get some water, get your hands wet and you can feel that bevel a lot more.
And that's how you know when to switch to a different side of the blade when you're
just starting out either on a file or a rough stone or a low grit sandpaper.
If you want to you definitely can screw an arrow on to the broadhead so that as you sharpen
you can hold it.
The only problem with this is there's a chance that you lift up the front or the back and
don't put enough pressure on it so what you can do is grab in the center, put pressure
there and then use it to help you go back and forth.
The other option to hold the broadhead is going to be both hands on it.
It's kind of small but if you can get two fingers on it I think that's the best way
to get even pressure along the whole broadhead.
I find that to work out much better than with the arrow, less room for error and allows
you to sharpen the whole thing consistently.
The nice thing about three blade broadheads just like this one is that you can sharpen
two edges at the same time.
What that means is that your cutting angle is not going to be as steep as generally what
a two blade broadhead is.
If I do the math right we've got six sides here and 360 degrees so I think that gives
me a 60 degree bevel on each cutting surface which is a really wide angle bevel if you're
talking about sharpening knives in general.
I think that's even wider than generally a hatchet or an axe would be sharpened.
But the benefit of that is that it's going to be a lot less likely you're going to get
chips on your blade because it's a wider angle.
It's going to make that blade much stronger.
Which for broadheads I think is perfect because this, when you get it razor sharp, it's going
to have no trouble with that wider angle getting a complete pass through on any deer or elk
or anything like that.
So I like this wider angle because it allows me to sharpen my broadheads each year instead
of buying new ones.
This one I shot a deer with last year and it wedged into its shoulder but it only bent
the tip a little bit and I'll be able to sharpen that up perfectly and use it again this year.
You can use some kind of lubricant or cutting fluid if you want.
I don't think it makes that big of a difference here.
On this broadhead you can see which areas are getting shiny and those are the areas
that's touching.
So there is a little divot here in the middle section so we want to sharpen it until it's
all shiny along the whole edge.
Another way you can test that is you can grab yourself a sharpie, run your sharpie on that
cutting edge, and then as you sharpen you'll see which parts are touching your sharpening
stone or sandpaper and which parts are not.
And then when the whole thing is shiny again you can move on to the next side.
Another good option, glue sandpaper on a piece of wood and then you can use that.
And then just move from your lowest grit up to your highest grit.
It is irrelevant on the exact grit, you just want to make sure you get that bevel before
you move on.
The most common mistake in sharpening anything is moving on too soon and then you're at the
highest grit and then you never roll the bevel in the first place and so it's not sharp at
all after you're at 2000 grit and you think it should be razor sharp but it's completely
dull.
Then you get frustrated when really you were just so close to getting it really sharp.
You just need to stay low until you get that bevel and then work your way up.
Now that we've moved up all the way to 2000 grit, you can stop there and you do have a
really sharp broadhead or you can continue going.
Lots of people use different things.
What I'm going to use today is a piece of leather.
And so I've got a piece of leather here.
I do not have white mold as some people call it or jeweler's rouge or whatever you call
it.
It's that white compound.
But I did want to add something to it so I added some oil, just some mineral oil on there.
Then with the leather, you really want to put down a lot of pressure.
A lot of pressure, come back, come back, come back and this is going to get it so sharp.
It's going to be cut through anything like hot knife and butter.
You just want to do backstrokes because if you push forward, you're going to be cutting
the leather and that's no good.
You can do it 30, 50, 100 times each side.
I think it's good to do it about 50 times, nice and hard on each side.
Two hands, keep the pressure even, go hard on that and then you have a glistening sharp
broadhead.
Thank you for joining me on this video.
Go sharpen your broadheads because when I stepped outside today, I smelt it and I felt
it and it made me smile and I wanted to run and jump for joy.
And if you're anything like me, you know exactly what I'm talking about.