Japanese woodworking - Door Rails: How to Install them

Shoyan Japanese Carpenter
89 followers
5 Video Views·Dec 24, 2022
Hello, this is Shoyan, a Japanese carpenter.
Today, I'll install door rails
in front of the lathe space I made in the last video.
The door rail of the top side is called kamoi in Japanese.
Draw the marking of mortises on the columns.
First, mark on the four corners.
Then, use a thread to mark on the center column accurately.
Next, cut out mortises on the columns to install kamoi.
There are grooves on kamoi,
so the mortises are to be the size of the whole of kamoi,
minus 15mm of grooves.
It tends to be misunderstood,
but kamoi is the door rails at the top side with steeper grooves.
The door rail at the bottom side with shallower grooves is shikii.
It has been generally said,
don't step on shikii for a long time in Japan.
So, shikii is at the bottom side.
Kamoi is at the top side.
It's often misunderstood.
Let's draw a marking of kamoi.
What I have now is called kamoi stopper.
It's called hanyaku among carpenters.
Hanyaku means half a man.
A long time ago, to support kamoi is disciples' work.
So, it's called hanyaku.
Next, draw the marking of kamoi.
To draw the marking of shikii and kamoi
is called hikaru in Japanese.
Basically, hikaru means to shine.
In this case, the word of hikaru is used to mean
to reflect the character of kamoi to make kamoi and shikii.
So, we use the word of hikaru.
Next, cut out it by fine-toothed saw.
I'm cutting out tenons.
These days, there are many carpenters
who process materials on stands,
but we are using saws with this kind of low stance.
This posture is more stable.
If the posture is not stable, I may make a mistake.
While making kamoi, put it at the position once
after cutting out it.
Then, confirm the accurate length
and modify the marking once again
based on the marking I drew first.
After the modification of marking like this,
cut out it one more time.
Chamfer the kamoi.
In the case of kamoi,
the groove portions also need to be chamfered.
OK, now processing kamoi has been completed.
Let's install it.
In this house, it's very difficult to install kamoi.
It's because this space is raised by 300 mm.
So, kamoi will be at the higher position
than usual cases.
That means there are less height above kamoi.
Columns cannot be bended easily,
so push the columns as strong as possible.
Then, install kamoi with bending it.
I pushed the columns to install kamoi.
So, pull columns back by hitting.
They are bended forcibly,
so they can return to the original position by hitting.
This is a portion of sewari,
so the center portion is sticking out.
Make it straight by hitting with a hammer.
Then, install kamoi.
Make here wider by jack as well.
Then, install kamoi.
The pitch of columns is narrow here,
but the column is thin,
so it was easy to install kamoi.
And pull the column back to the original position as well.
As soon as possible,
apply water at the damaged portion
or the portion where I did kigoroshi.
By doing like that,
the dents will become as original.
Lastly, fix it by screws from the top side.
Then, it's completed.
Next, let's install shiki.
Confirm the level and cut out mortises.
The mortise of shiki is different from that of kamoi.
It's thin, only 15mm thick.
This is because one end is fixed by mortise
and the other end is fixed by dowel.
I think you can understand after watching it.
The hole for dowel is a little deeper than the dowel itself.
It's much more difficult to cut out the mortise of shiki
than that of kamoi.
It's thin and at the lower position,
plus the space is narrow,
so it's very difficult.
The floor has been fixed until shiki portion.
So, to remove the portion of conflicts with floor,
I'm cutting out shiki at the thickness of floor.
Actually, the floor is 30mm thick,
so considering margins,
cut out at 32 to 33mm.
Without doing like that,
if the floor is curved,
there will be the force to raise shiki up.
So, it's important to consider margins.
Then, make dowels to fix shiki.
Its size is 15mm by 15mm.
Adjust the length as well as kamoi.
In the case of shiki,
I can draw marking on the floor,
so it's much easier.
Cut out tenons of shiki.
It's difficult to cut out the size of material by manual saw.
Generally, we carpenters use manual saws like this way
that the front end is lower.
But these days,
there are many carpenters
who don't use manual saw in this way.
When I was a disciple,
I was said that
if the front end of saws is lower,
it's the way of doormakers.
I don't know why.
Actually, this posture is better for me.
Generally, it's said that
it's a bad habit to step on shiki.
But it's OK to sit on it.
People often sit on shiki at verandas.
But it's said that
standing on shiki is as rude
as standing on father's head.
Adjust the dimension of dowels
that I made roughly.
Make it become tight
when installed in mortises.
Usually, I don't apply glue here.
But in this case,
I want to integrate it with box of doors.
So, apply glue this time.
Then, apply water on columns
not to damage it.
And install shiki at once.
By applying water,
damages can be prevented.
And I can install shiki by sliding it.
Adjust the position of shiki
and drive-in dowels.
This dowel is not for the strengths.
It's to fix the height and twist.
So, there are small margins at both ends.
These days, shiki is seldom changed
with new one.
But it often used to be changed.
At that time,
if there are no margins at both ends,
the dowels cannot be removed.
So, these margins are necessary.
Fix the back side of shiki just in case.
Cut out the other side as well.
Shiki and kamoi
are the parts called
uchinorimono in Japanese.
To process this kind of parts,
3 or 4 years training is necessary.
It's possible to determine skills of carpenters
through this kind of work.
It's an interesting part, actually.
I like this kind of works.
As you can see,
shiki is installed at once.
If I move it by stepping on it many times,
it will be damaged at each time.
So, it's better to step on it at once.
OK.
Now, I've completed shiki,
kamoi, and storage portion.
That's all for today.
Thank you for watching.
