Japanese woodworking - Raised Space: How to Finish it

Shoyan Japanese Carpenter
89 followers
65 Video Views·Dec 24, 2022
Hello, this is Shoyan, a Japanese carpenter.
Today, I'll finish the 300mm raised space
finished with tatami that is a Japanese floor material.
This space is as large as 4 1⁄2 pieces of tatami.
Now, there are substrate materials fixed already.
These boards were fixed at the time of flooring of the whole of this house.
I use damaged boards so that trashes don't fall into this space.
It's like the substrate materials of substrate materials.
It's been many days since I fixed these boards.
So, fix the boards by larger nails again to prevent sound and bend the floor.
I checked the level first, but I confirmed the level once again.
First of all, cut out the frame members of drawers for the storage.
This is 30mm thick cedar board of laminated wood.
Cedar is half as heavy as Japanese cypress.
Here will be 3 numbers drawers for storages.
It's narrow space.
The drawers will be made by furniture dealer.
So, I'll make the frames like boxes to install drawers.
Laminated wood tends to be curved.
So, make the curved material straight.
If it's not straight, I cannot cut it at right angle.
Cut 4 boards for partitions.
The height of drawers is only this much.
Finish 4 boards by sander at the same time to be the same lengths.
This material doesn't have nags.
To be honest, here will be invisible.
So, it's a little too expensive actually.
But it was surplus material.
So, I use this one.
Each member is fine.
So, let's install them.
Use clamps for installation so that I can drive in screws easily.
This part will be invisible.
So, fix it by screws as usual.
This material is cedar.
I think it will not tear.
But just in case, make a hole before driving in screws.
Install frames for storages at the position.
The decorated board will be installed to cover the front side.
Use Tarusen to make it good-looking.
Even through invisible portion also.
Fix the board of back side as well.
Without fixing the back side board tightly,
insects will come in.
In this house, I'm not using the materials such as
veneer, processed material, something like that.
I'm using materials that are good for healthy.
Regarding glue also, I'm not using glue that is too strong.
So, this house doesn't harm house.
Next, measure the height of the floor level.
The floor level is matching the top side of the storage.
The floor is raised by 300 mm.
This kind of raised floor is popular these days.
A long time ago,
floors of old houses used to be raised by 200 mm
that is thickness of door rails.
The raised floors of these days imitate that.
To make the storage below the floor,
300 mm is necessary to make spaces.
I'm using seepers, not joists, to fix substrate materials.
I install seepers at narrower pitches than usual.
30 mm Japanese cypress board
can be finished directly on seepers at 900 mm pitches.
It's called Lost Joist Method.
This time, I make the pitches 700 mm.
The support of plastic is easy to install.
But this time, I install wooden supports.
Of course, install the support
at the intersection of seepers and joists.
Process floor materials.
This is 30 mm thick board of Japanese cypress.
This also a little too expensive for here.
It's 30 mm, so it will be sturdy.
Start to install it from the area above storage spaces.
The first board is conflicting against the column,
so make notches at the both ends.
The substrate material of the box is 30 mm thick.
Apply glue on it and fix on the floorboard tightly.
This floor will be under tatami,
so it also will be invisible.
So actually, it's OK to drive in screws vertically.
But drive in screws diagonally as usual
to fix it more tightly than vertically.
OK, I've finished the raised floor.
In the next video,
I'll show you how to finish door rails.
Please check it.
That's all for today.
Thank you for watching.
