Japanese woodworking - Straight Staircase Installation

Shoyan Japanese Carpenter
89 followers
14 Video Views·Dec 24, 2022
Hello, this is Shoyan, a Japanese carpenter.
Today, I'd like to install straight staircases
above and under the spiral staircase
that I installed in the last video.
First, draw the marking of stringers.
Stringers are the long boards
on the both sides of staircases,
the support step boards.
Measure the dimension of step boards by square scale
and draw the marking one by one by scale
whose angle is adjustable.
The height of this staircase
can be divided by 200mm
and the width of step boards is 210mm
so the slope is 210 by 200.
Draw the marking of the front side of step boards
by this tool called KB key.
This KB key can copy the same dimension
to the other materials.
This kind of work used to be done marking ink before
but ink will be a problem at the time of finishing by plane
and some mistakes can happen by marking with a square scale
so KB key is the best for this kind of job.
OK, now marking is done.
Let's cut the both sides of the stringers
and install them at sight.
When I use a circular saw,
if I try to cut a timber at once,
the blade will be caught by the timber
then kickback can happen.
Regarding materials,
this stringer is made of cross grain timber.
At the time I cut cross grain timber,
if I slide the blade of the circular saw only from one side,
the blade is often caught at the middle of material
and the blade will be stopped
or kickback will happen.
For prevention of such a situation,
cut the back side first
then cut it from the front side slowly.
This is a safe way to cut timbers by circular saw.
This staircase has 14 steps.
By the way,
13 steps of staircases have been hated for a long time.
It's been said that the staircase of gallows has 13 steps.
I don't know it's a real story
but it's a reason why it's better to avoid
to make 13 steps of staircases.
Finish the both sides of the stringer and install it.
It's difficult to fix it at once
so adjust the angle and height a little bit
then install it.
Cut out the opposite side as well.
When I cut out the stringers of both sides,
if the marking is wrong,
the whole works will be useless
and should be redone.
So, before cutting out it,
confirm there is no mistake by comparing them.
Then, cut out grooves.
The stringer of this side is touching the spiral steps
that I've installed in the last video.
So, trace the slope of spiral one
then shape up the end of the stringer.
I can shape the end portion diagonally like this
because it is made of pines this time.
Cedars and cypresses cannot be made this sharp shape.
Fit the stringer at side like this for trial.
OK.
Confirmation of both stringers has been completed.
Let's cut out the grooves for stepboards.
First, make guidelines along the marking.
Using a cutter,
make guidelines of the outlines of grooves.
Next, decide the depth of grooves
and cut out them by groove cutter.
Now, I'm cutting out the groove
by freehand without scales.
It's a little lazy way
but it's faster to cut out all grooves by freehand
than to making a scale.
So for me, it's a better way.
When I cut out grooves,
the edge of the grooves will be turned off.
The purpose of the guideline that I've done before
is to prevent this problem.
Grooves can be cut out roughly with machine
but finishing has to be done by manual chisel.
Thanks to the guideline,
I can cut out the edges accurately.
So that guideline enables me
to finish this kind of job easily.
OK.
Grooves for steps have been completed.
Shape up the edge portion
where wall boards will come.
Next, plane stringers.
The stand is not stable.
I should have fixed more tightly.
I have to plane only visible portion of the stringer
so it's not a big shock.
But this stringer is hard to plane actually.
If I use an old plane and my fingers slip off,
my fingers will be caught at grooves and get injured.
So I should be careful to plane
this kind of difficult materials.
Now I'm choosing step boards.
Decide the order of the materials
to use better one from the bottom side of the staircase
and number them.
Next, make grooves to fix rise boards
on the bottom side of step boards by roof gutter.
Measure the length of step boards
and mark on a bar to use it for reference of dimension.
This is called baka-bo.
Baka means stupid in Japanese.
Even stupid one can do exact marking easily by this bar.
So it's called baka-bo.
Cut step boards using baka-bo.
Materials are little longer
so check the cracks at the end of materials
then cut the boards as well as I showed you.
This time also, cut the back side first
then cut the board from the front side.
The rise boards are the same length as the step boards
so cut them to be same lengths.
Next, finish the step boards.
Seen in the video, step boards seems to be short
but it's as long as standard staircases.
Plane the back side of step boards a little diagonally.
This is the portion where rise boards will attach.
By planing step boards diagonally like this,
rise boards will be fixed easily.
Chamfer the corner of the back side.
Here rise boards will come
so make bigger chamfers.
This is a step board.
Make bigger chamfers on step boards as well.
Now I'm doing kigoroshi.
Kigoroshi is to dent timbers by hitting with a hammer.
The grooves of stingers are cut out
based on the dimension of dented step boards.
So it's more narrow by 2mm
than the original thickness of step boards.
After the installation of step boards,
apply water on them.
So that the boards expand until the original thickness
and become tight.
Lastly, make grooves for slip prevention.
OK, processing the materials has been completed.
Let's install them.
First, fix them by longer screws.
To fix the stringers, I can use screws
as the groove set will be hidden lastly.
So use many screws to fix it tightly.
Fix the step boards that I did kigoroshi.
Even after kigoroshi,
it's a little hard to install.
It's a good adjustment of dimensions this time.
Then, apply water on the step boards
to expand them as original.
They don't expand at once
but gradually become as original.
Thanks to this work,
they will get tight and stable.
Fix the step boards by screw
from back side towards the front side
and drive in 3 more screws
from the bottom side to make it sturdy.
There is a misalign between
the surface of step boards
and the grooves for rise boards.
So adjust the misalign.
When I install the rise boards,
apply plenty wood glue on the top side.
And this time, fix them by 15mm screws.
For the top side,
15mm is too long.
So use 45mm screws.
Make holes on the sides by sick drill
and drive in screws as well.
Rise boards are easy to be cracked.
So the portion where screws are driven in
should be taken care soon.
I'm applying wood glue.
It's enough for prevention of cracks.
Lastly, I apply 20mm thick wood glue once again
on all end portions
not to be cracked immediately.
Fix the top side tightly
from stringers as well.
Regarding the last rise board,
here is a horizontal member.
So I cannot fix it from the back side.
So this time, make a hole by drill.
Drive in a dowel
instead of screws from the back side.
At this location,
the rise board is fixed only by wood glue.
So make sure to apply the glue
in the hole using my finger.
Then, apply wood glue on the rise boards as well
and install the last rise board.
After installation of the rise board,
fix the dowel by screws.
This supports the board from the back side.
Now all of the staircase has been completed.
This is a staircase made of red lines.
It looks splendid.
That's all for today.
Thank you for watching.
