How to Build a Greenhouse

Family Handyman
185 followers
28 Video Views·Dec 23, 2022
Hey this is Mike with Family Handyman. Over the past few weeks we have been working on this
amazing greenhouse. We placed it into this underutilized spot in this garden so that
the homeowners could start their seedlings and get a jump start on their growing season
and then transplant them only a few feet away right into their garden. We used cedar and
polycarbonate and it only took us a few weeks to build it. Let me show you how we did it.
We removed about eight inches of topsoil to make room for our base layer of rock.
We leveled and compacted the dirt, rolled out heavy landscaping fabric, then added a layer of
three-quarter inch limestone. Next we created a mini retaining wall using landscaping timbers.
We placed, leveled, and squared three sides of the retaining wall leaving the fourth side off
until most of the rock was dumped. We secured the timbers at the corners with eight inch timber
screws and fastened a pressure treated board to keep the timbers together at the seams.
When most of the rock was dumped and evenly spread we put the fourth side of the retaining
wall up. So the foundation is complete, all the rocks in, it's tamped out, and it's level.
Now we are ready to start framing up the walls. We'll begin with the sides and the back.
The front will be done a little bit differently but we'll address that when we get to it.
To build the walls we use pressure treated two by fours for the bottom plates and cedar two by
fours for the top plates. I cut them to length, spread them out, and then started attaching the
studs. Once I built the wall I added a second pressure treated bottom plate and this will make
it easier to level out the top of the wall once I get it tipped up. So then I worked on the back
and the opposite side walls which are constructed the exact same as the first wall. Once they were
braced up I fastened them at the corners making sure that the top plates are nice and flush.
So before we begin building the fourth wall we're going to spend some time and make sure the walls
we have up are nice and level across the tops. We're going to have to take some rock out in some
places and add some in underneath the walls. We've got our walls in position and locked in place with
these blocks that are screwed to the timbers. That way we level off the right portion of the rock.
Once we have that done we're going to build our fourth wall. So the front wall is built slightly
different than the back wall. The layout's the same, the studs are in the same spot, but we have
taken out these three middle studs here because we need to make room for a door. Now the walls are at
six feet tall and the door is going to be bigger than that. I wanted to build this so all the
corners are connected and all the walls are tied together so it stayed nice and rigid while we were
building the roof. So once the roof is installed that'll tie in the corners and the walls all
together and then we can come back and cut the top and bottom plates out to make room for the
door. To hold the walls to the ground we found this really cool ground anchoring system. It's by a
company called American Earth Anchors. It's a three inch bullet that gets pounded into the dirt through
the plate and then on the top end you've got this cable that you thread through this washer system
and it automatically cinches the cable and holds the plate down to the ground. Once the walls were
anchored to the ground I went to each corner and made sure they were plumbed and braced them into
position. So I just got done assembling this table that's going to help us get the rafters cut and
then assemble the trusses right on this. It's going to make this process a whole lot easier
that way we're going to have the cuts right, the lengths right, and everything is going to assemble
the same way. A lot faster when you're doing a bunch of trusses like this. I position the rafters
on the table then mark the bottoms to be cut. I then cut the rafters down put them back on the
table and assemble them with a collar tie. So since our walls are nice and level and we already have
this jig built to cut our rafters and assemble our trusses we're going to use it to also install
our gables. So I'm going to double up one of the trusses here and then add a plate to the bottom
of this so that our plates are doubled and then I can install the cripples in between. Then we place
the tails of the gable on the wall and then use a long board to tip it up and brace it in place.
Then we fasten the gable to the wall through the top plates. After we fastened the gable we added
a second top plate to the walls to fasten the trusses to. Then I cut two by four blocking to
match the spacing of each stud bay. I attached one of these blocks to the gable 36 inches down from
the peak on both sides. This will allow me to add the trusses and keep their spacing even from the
studs all the way to the peak. We used special screws for trusses to fasten them to the walls.
So now we're going to work on installing the door. Since our walls are only six feet and our door is
taller we'll have to cut out the top plate here but first we need to take some measurements from
the door, transfer those to the wall here and then start framing. We need to fit in a 36 inch
door and the framing that will hold it. So we marked out a 42 and a half inch opening in the
center of the front wall and cut it out. I cut king studs to fit from the bottom plate to the gable
truss. I plumbed them and fastened them into place. Then I added trimmer studs to fit the height of the
door and a header to finish out the framing. So I've got the door installed. Next up we're going to
install the sheathing on the lower half of the greenhouse. The only thing to note about the
sheathing is to make sure that the top is nice and level and to split any seams onto a stud so that
both ends of the sheathing can be nailed. So we've got the sheathing installed now I'm working on the
sill which is basically a way to get more water away from the greenhouse. Now if it sat flat
against here the water would pool up that's why we did a small five degree bevel on the back side
to tip the sill downward. The other thing I've got going on is this drip kerf here which will allow
the water to drip to the ground instead of wrap around the board and weep back towards the
greenhouse. Then we fastened two by four blocks between the studs to attach the sill. Then I added
some trim to the corners over the sheathing which will make installing siding much easier.
Now it's time to start sheathing the greenhouse. We had a few choices in that. First of all we could
have used tempered glass but that would have been really expensive and very hard to cut to size.
Really that's the Cadillac of this type of material here for the greenhouse. What we chose was an eight
millimeter thick twin wall polycarbonate and we chose the soft light version as opposed to the
clear version because it lets 80% of the light through and it diffuses the light really well for
nice even light inside for the plants. I cut the polycarbonate to size and fastened them to the
studs using two inch stainless steel roofing screws. At the same time we started installing
the siding. We used ring shank nails and made sure each course was level and matched up at the corners.
After the polycarbonate on the walls was up I cut a piece of one by six cedar to fit beneath the edge
of the roof for the fascia. For the roof I started by applying a strip of butyl tape down the center
of each truss. I positioned the polycarbonate then secured them with one by four battens
through each truss. After installing the roof I moved to the gable ends by installing some
freeze board. Then to seal off the ridge of the roof I attached a ridge cap. I cut it to
size and then fastened them with two inch stainless steel roofing screws. So the outside's nice and
buttoned up. We are going to work inside now focusing on a few of the features. First up this
bench from wall to wall here along this side. It's going to be used to set seed trays on and pot some
plants. Really nice feature of a greenhouse. Really simple construction two by four and cedar decking
should go fast. Let's get going. As you can see we're all wrapped up with the greenhouse. We just
finished building the benches and they offer a really great working space and a nice space to
set your seed trays. They also offer a great space to store your extra soil, mulch, watering cans,
and other items you need for the greenhouse. Looking up here we've got two circulating fans
which will simulate real wind which really strengthen up the plants like they're outside.
And then we've got our grow lights up top all the way around which will offer perfect light
24-7 for the plants. Finally we've got this really cool vent fan up here which can automatically
turn on and off based on the humidity and the temperature found in the built-in sensor. So
that's it. This thing is ready for use. For other great projects like this head to familyhandyman.com
