Japanese Woodworking - Floor of Cypress Without Knots [Season 2 - Part 4]

Shoyan Japanese Carpenter
89 followers
13 Video Views·Dec 19, 2022
Hello, Shun here.
I'm a Japanese carpenter.
Last time, I installed the joists.
I'm going to install the floorboards this time.
First, measure and mark the joint position
on the end of the flooring material
before installing it.
These boards are basically two cans.
Therefore, shift the boards one can at a time
and install them using the Ranko-Bari method.
Even the dimensions are not the same,
you can find the center of the joist
and match the lengths.
Measure and mark the position of the joint
on the floorboard's side as well.
To determine the joint's position on the side,
divide the width of the entire house
by the width of the board
and make sure that it doesn't become narrow at one end.
There is a round pillar in the middle of this site.
I'll also measure and mark from the joint.
On one side of the room,
there is a sliding glass door with an angle,
so I'll start installing from this side.
As I have a hard time remembering things,
I'll be sure to write down the actual dimensions.
Now, cut the floorboards.
The floorboard is Japanese cypress.
It measures 30mm thick, 105mm wide,
and 2 cans long.
Each color is different,
so I will find a match for each board
to make it as close as possible.
When you cut the joint,
you'll need to leave a little bit of clearance
on the back side.
It means cutting at a slight angle.
This angle will help the top side to install tighter.
Instead of cutting each board
and installing it one at a time,
I'll temporarily lay out half the room.
That way,
I can see the color and grain balance of the entire room,
not just the spacing of the joints.
Truthfully,
it's hard to work temporarily laying out the boards.
Stack the temporarily arranged boards in order.
With this number of temporary arrangements,
it takes 3 hours.
Now, install the boards.
Measure the first board's front side.
I measure the board's width
by checking it in several places with a string
to avoid overlapping.
Then, calculating backward
from the first board's dimensions,
I'll measure the board's width
to the bottom angle of the sash.
I'm using the Cypress material,
Joukou Muji.
There are grades.
If the wood is full of knots,
it's called Itto.
The next grade is called Joukou,
which has fewer knots or curves in the grain.
And the top grade is called Muji,
a beautiful board without knots.
Joukou Muji is a board
with a mixture of Joukou and Muji.
I'll install the boards
hiding as many of the knots as possible.
And try to make Joukou looks like Muji.
Secure it in place with non-toxic glue
and 65mm screws.
The glue bottle is refillable,
so I can squeeze it out
and use it until the end.
There are many pros and cons to the glue,
but it will stick well
depending on how you use it.
Now, install the floorboards
from the bottom of the sash angle.
The angle part of the sash can easily shift.
As the sash shifts,
the first floorboard will shift.
As a result,
the entire flooring can move.
Make sure to thoroughly check
the length of the floorboard
as you carefully install the first floorboard.
Install the second floorboard.
After jointing the first and second floorboards,
check the entire length of the floorboard again.
The first floorboard
is the most important when installing.
If the floorboard is not straight,
the joint will not match
the floorboard's right angle.
Even if it appears straight,
it can gradually move.
If it's moving when you start,
it won't fit at the end.
But the good thing about solid boards
is that they can be adjusted
even if they shift in the middle of the board.
It's just a matter of
cutting off the protruding parts
little by little.
Now that I've installed some flooring,
I'll move the cutting area.
To install a new floor section,
I have to move to another place in the middle.
Process the log pillar
in the center of the room.
I'll chisel off the bottom
so that the floor can fit in.
It's called kubikiri.
In Japanese, it's the same as restructuring.
If the pillar is round,
I can trace and chisel it neatly.
If I chisel off the part,
gaps will not appear
even when the pillar dries out and shrinks.
For that reason,
I'll chisel 15 to 20 mm into the pillar
and insert the floorboard.
That is called kubikiri.
No matter how often I do kubikiri,
it's always a difficult job,
especially with the stance involved.
I can still work between the joists
to lower my hands and eyes.
If the plywood panels for the base
had been in place,
this would be much more difficult.
It looks easy, but it's a tricky job.
I may appear to be cutting off a lot,
but this pillar isn't holding much weight.
The design of the house
is for the structure to remain strong without it,
so there's no problem.
I was able to position the joint of the board
at the corner of the pillar as planned.
Therefore,
I don't have to do any troublesome yabio-kuri.
Insert the board firmly until it sits tight.
Insert the board properly
to fill the kubikiri area that is chiseled.
I managed to make it beautiful.
It looks like a cedar log has grown out of a cypress board.
Do the kubikiri on this thick pillar as well.
The design is for the thick pillar
to look like a central pillar.
It doesn't penetrate to the second floor,
but it deserves to be a splendid central pillar
on the first floor.
This floorboard's joint section
also fits the core of the pillar.
As before,
I can install the floorboard from both sides.
Since one of the floorboards will be at the end,
I cut off and angled the floorboard
to install it easily.
The pillar could be damaged
when installing the floorboard from the side.
Use a piece of wood positioned above
to hold and guide the floorboard
when installing it from the side.
The board in front of the entrance valve is short.
I shaved down the edges of the wood one by one
and installed them.
This site comes equipped with a wood stove.
I used a curing board to make a paper pattern
for the cell where I will lay the tiles.
Use the paper pattern to outline the protruding floor.
Then, cut it out with a circular saw.
The three sections will cut easily,
but the corner part is more difficult to cut
with a circular saw.
To remove the end-tubes of the jet saw
using tin scissors.
If you do it this way,
you can cut corners easily.
Some joists are low and some are high,
so cut out the parts that you don't need.
Then, chisel off the top edge
of the protruding higher joists to match the lower.
If I cut them out,
I'll need to install more supports and sleepers.
For that reason,
I chiseled off the top edge
to make the joists the same thickness.
It's much stronger this way.
Install the plywood panel as a foundation
for the wood stove floor.
I don't want to use a plywood panel,
but according to the fire service law for a wood stove,
the floor should be covered
with a 12mm plywood panel,
12mm calcium silicate board,
and tiles.
Therefore,
I have no choice
but to use a plywood panel in such cases.
I'll install the stile of the wood stove
after the plywood panel is in place.
I can't bear from the side of the stile
after installing the calcium silicate board.
I also use Japanese cypress for the stile.
The top side will be straight green.
I was able to make all the pieces
with 1mm lumber.
In their cut order,
connect the pieces starting from the corner.
Make sure that the straight
and cross grain are aligned.
The corner's 45 degrees milter joint
is a bit tricky,
but nowadays,
I use a siding milter saw to cut it,
so it fits at once
if I set the angle correctly.
Glue the stile firmly
and screw it at small intervals.
Lastly,
plane the stile to level it
and correct any misalignment.
The stile is now in place.
After this,
I install the double layer
of calcium silicate board.
I've been installing the floor
for three days.
This board is a mixture
of Muji and Joco,
but I managed to install
the main floor without knots.
To see Japanese cypress without knots
is very beautiful.
I'll keep working hard
to install the rest.
That's all for today.
Thanks for watching.
