What's up friends?
Welcome back to the cave today.
It is Thursday and we're gonna build a tillering tree
and I'm gonna show you how to do so.
If you're new to building bows,
this will be beneficial to you.
Or if you just are curious about it,
I love having you here.
On Thursdays, we're doing archery tips
and bow building tips.
We'll make them quick videos.
We'll make them informational and also entertaining.
So I hope you enjoy.
I really just have been blown away
at all of your guys' kindness
and helping me create this awesome community.
So I wanna give back to you guys.
I'm gonna give away five free two-tone tabs.
They're pretty stinking sweet tabs.
And the only way to get them is through giveaways.
We're not gonna sell these tabs.
We only wanna give these ones away to you guys.
So we're gonna give away five of them.
You can choose split finger or three under,
whatever you prefer.
But the way to get your hand on one of these tabs
is you need to do that over on Instagram.
So this post right here,
you can go check that post out on Instagram.
It'll give you instructions
on how to enter for the giveaway
so that we can get you one of these tabs.
I really just wanna say thank you so much.
In the past six months,
this YouTube channel has changed my life.
It's been so fun.
I've got to get to know so many of you guys.
And I don't know, I'm just very grateful.
Anyway, I'll stop.
Let's get back to the video.
I did a video a while ago
about everything you need to know
about tillering trees and tillering sticks
and the difference in the two.
I showed how to build this pulley system.
Most people call it tillering tree.
And then I also have a tillering stick
that I kinda refinished.
But I wanna show you,
if you're gonna build from the start,
how to build a tillering stick,
what to look out for.
There's a couple things
that will cause you some frustration
and the bow will fall off.
Also, how to do it with limited tools.
So the first thing you need is some wood.
It can be scrap pieces of wood
or you can just go buy one two-by-four
and you can do all of this with a two-by-four.
The one thing you need to make sure your wood is
is at least 30 inches long.
That will allow you to have full length of draw
on your tillering tree.
The nice thing about making a tillering stick
is that you don't really need any power tools.
You can just do this all by hand.
I'm gonna use this other piece of scrap I got
to hold the bow in place.
Hey, not all of you know this yet,
so I have to interrupt.
Power hour is something that happens
the first hour after a video is posted.
I hang out in the comments
and comment back to every single person I can.
So if you wanna talk to me right after the video,
power hour, first hour after this video is posted,
comment to me and I'll be there hanging out.
Subscribe, hit the bell notification
so that you can be notified
and watch the video in the first hour
so that we can hang out.
I'll see you in the comments.
I'm gonna go ahead and cut this
into two six-inch sections.
So I'll end with a 32-inch piece of wood
and two six-inch sections of wood.
I've now got my one 32-inch section
and my two six-inch sections.
Go ahead and mark an inch and a half down
on both six-inch sections.
Place that inch and a half mark
right where the top of the tillering stick comes
and then screw the six-inch sections
into either side of the tillering stick.
The bow handle will rest right in the slot we just created.
Now if you need a wider slot,
you can always shim it out with a piece of plywood
like I have over here on my tillering tree.
But if you wanna make it smaller,
you can always slide a little piece of plywood
on the inside here or use some kind of rubber
or leather to fill the gap.
If you're building a board bow,
this method is a really good option
to use two-by-fours or two-by-sixes.
When we build a board bow,
we often use one-by-twos as our bow building wood,
which naturally the handle's gonna fit perfectly
because it's the same width as your two-by-four.
Now that we have the slot cut,
it's time to measure our mark
to be able to cut out our notches
that we can draw the bow down.
Draw length is measured from the back of the bow.
Each bow handle is gonna have
a different level of thickness.
That's why we had these an inch and a half up.
An inch and a half is the most common thickness
of a riser section of somebody building their own bow.
Go ahead and measure out from the top all the way down,
marking every single inch.
Now all we need to do is cut out notches.
We're gonna cut out notches that look like this.
The handle is that way.
So from the handle, it cuts straight out.
If you cut these notches in backwards,
your string's not gonna hold.
You don't have to cut the notches in very far either.
Just about three widths of a bow string
is basically what I do.
In other words, I'm gonna come in about half an inch
or slightly below it.
With hand tools, I just cut horizontally onto the board
and then I would chisel out the other section.
And if you don't have chisels,
you can actually even cut at a diagonal
into the board with a hand saw.
Now, for using a hacksaw, that's not too bad.
If you have a table saw with a table saw sled,
you don't have to have a diagonal mark in there.
You could, you could do one at 90 degrees
and then do another one at 45 degrees to make that.
But you can just use a table saw sled
and just do two saw blade lengths of thickness,
about half an inch into that piece of wood.
And that's gonna be plenty for you
to get the bow string in there while you're tillering.
You may want to run a little bit of sandpaper
on the corners here so that it doesn't cut the bow string.
But I'm all about different methods.
And so another method I've seen people do
is to grab a screw, screw a screw all the way in there.
The main thing you want to make sure
is that it's a smooth shaft near the top.
If the threads go all the way up to the head of the screw,
don't use that kind of screw.
Only use the kind where the threads stop
so that you'll have a smooth area
for your bow string to go on.
With this method, there's less area
the string will be holding,
which will cause it to wear out in that specific area
a little bit faster than if you're evenly pressured
along the whole edge.
Plus, on top of that, a screw is not realistic of shooting.
If you're shooting with three fingers,
it's gonna be the same width of a board,
not the same as this.
So the tiller will be slightly different
depending on which method you choose.
But it's an option if you like that.
Another option I see people do is to pre-drill holes
and then use a wooden dowel to stick into each hole
so that they can move their dowel up and down
depending on where they want to draw their bow to.
Now there's endless mounting options for this.
You could just screw it to your workbench.
You could put it in a work vise.
You could just set it on the ground
and put two bricks against it.
Whatever you have at hand, you can use to make this hold.
And even if you have nothing else,
you don't really need it.
You don't have to have it to hold into place.
This right here will hold a bow.
You can draw a bow down, put it on there,
draw it down to the first mark, set it back,
take a look at it, see what you think,
and then take it off.
The other cool thing about something like this
is if you have a wall you can screw it to,
or maybe, like my last garage that was unfinished,
I just had two-by-four studs in there.
I could have just screwed this front board
against that two-by-four stud
and then screwed a couple screws into the stud
and literally just set the bow in the top there
and draw it down and use the stud
as actually part of the tillering tree.
So if you're getting into bow making for the first time,
this is what I would recommend building.
It just takes a few pieces of scrap wood
or a $3 two-by-four.
Once you have a tillering tree built,
one of the most difficult things
is to not have the handle wobble back and forth like that.
How you can prevent that
is either to not shape your handle so it's square
until the tiller's looking great.
You don't need to shape it at all until the very, very end
because that's the only time you hold it to shoot.
But if you've already shaped it and it's rounded
or it's not fitting well,
all you need to do is get some pieces of leather or rubber,
anything to wedge in there on the parts
that is making it wobble.
And just by wedging it in you'll get something solid
so that you can draw this back
without the bow twisting back and forth like that.
Hey guys, if you like this video,
go ahead and subscribe.
That'd mean a lot to me.
Only 10% of you are, so nine out of 10 of you aren't.
And if you don't do it soon,
you won't be able to say that you were part
of the first 100,000 subscribers.
So it really means the world to me.
Blows my mind how many of you guys are here.
Seriously, thank you so much.
Stay positive and be shatterproof.
Remember, I'm for you.
And I'll see you on the next video.
Go make a bow.
Peace.