Installation of Solar Module Mounts and Inverter Installation / Quarter million investment

Семен Кузнецов
75 followers
4 Video Views·Dec 11, 2022
Hello everyone friends In this video I will be mounting the solar panel brackets and installing the inverter in the right place
Have a pleasant viewing
Let's start
On this channel you will find more than 180 episodes about building a small permanent house with a summer terrace
In the previous episode I gave a brief overview of the equipment of our networked solar power plant
3150 watts Now is the time to start installation Before installing the heterostructures
We need to install reliable and high-quality mounting systems for the HEVEL solar modules on the roofs
The mounting base consists of an aluminum profile and additional mounting components such as
A U-shaped bracket with a rubber gasket and screw This bracket serves as a base for securing the profile to the roof surface
A central clamp is used to connect the two panels together For the initial and final panel attachment
The terminal clamp is used To extend and lengthen the profile a profile connector is used We will have a mounting option
e simplest flat one If you want to set the desired angle for your solar panels this one is used instead
L-shaped mounting Front and rear legs with adjustable angle
The optimal year-round angle for our region is 47 degrees From the very beginning I had planned
Mount the panels at angle like this When placing the order the managers from Volta Energy advised me that with such angle
The first row of the panel will cast a shadow on the second Also installing such supports on our metal roofing
SuperMonterey is a whole problem And when I additionally found out that the loss at our corner of 7 degrees would only be
8 percent I thought damn a 7-degree angle is quite enough for me Of course the snow will have to
Clean but winter will show Maybe in the future I will make some changes related to the panel angle Well let's assemble the scaffolding and
We proceed with the installation of the brackets
I start the installation with L-shaped brackets Each bracket comes with a stainless steel screw Its length is longer than the thickness of our
Wire mesh and lattices Approximately 1 centimeter To avoid damaging our membrane with these screws slightly grind them down with a grinder
At the end of each screw there is a kind of drill so I will leave one screw untouched I will use it to drill into the metal sheet
When tightening screws this part will get in the way so I'
ll remove the interfering parts
from all L-shaped fasteners
The first L-shaped fastener is installed Despite the fact that each fastener has a rubber pad
I also use roofing sealant to make sure everything is of high quality
I'm installing the new bracket for the sixth wave That's approximately 110 centimeters
I attach the L-shaped bracket tightly to the wave make a notch with a screwdriver
I remove the fastener and drill in the screw
Then I unscrew it apply the sealant and complete the mounting installation
I am repeating the same process across the entire roof
It's not a difficult job Here's what I would do if the angle were about 45 degrees Nothing I'd just hang from the rope
My wife asked me to hold the ever-falling tool I'll make the second row of the future profile mounting on the fourth wave
Here it all depends on the size of your panels Our Hevel panels have a length of
167 centimeters in height 100 centimeters in width and 35 millimeters in thickness
It all lines up perfectly Look
The L-shaped bracket is installed It's time to install the aluminum profile
First I secure the ends of the profile and then move to the middle I secure the profile as high as possible from the ceiling
Tighten the bolts with an Allen wrench
The first profile is locked in Moving on to the second
I make a gap between the profiles of a few millimeters The main thing is not to have them tight You never know there might be thermal expansion
Two profiles are mounted connecting them together with a connector
The first upper line is ready I am repeating the process on the remaining three
Our panel fasteners are ready The service life of such
fasteners exceeds 25 years Aluminum
Let's see Now I will mount the Safar network inverter on the wall
This inverter can be mounted indoors and outdoors
If the installation is outdoors the main thing is that it should be under a roof and in the shade I decided to install it on the summer terrace
The closest possible to the water electricity in the house I'll fix it right here Perfect
The inverter is mounted on the mounting plate I mark the positions drill the holes and screw in the anchors for the gas concrete
The dowels are in place Securing the plate
The original screws were weak I replaced them with good sewing screws
The plate is mounted Installing the inverter
There is a gap between the wall and the inverter I think the ventilation should be good
According to the instructions the inverter must be grounded Preparing the grounding for future use
I use a 6 square grounding wire
The wire will be left with about a meter The grounding cable will be in the panel next to the inverter
My grounding system is located under the terrace I installed it about two years ago If anyone is interested in how I did it you'll find a link in the description
The panel mounting is ready The inverter is on the wall You can proceed to install the HEVEL solar modules and assemble the AC and DC panels
You will see this process in the next episode It won't keep you waiting
Thank you for watching this video I wish you good luck See you soon Goodbye to everyone
