How to build a portable WALL (COOL IDEA) _ DIY Creators

DIY Creators
91 followers
1 Video View·Dec 10, 2022
Right now I'm doing more video calls than ever and I know I'm not the only one
running around trying to find a place that's presentable to take these calls.
And for that reason today I'm going to show you how to make a mobile wall that you can use
as a background, room divider, or anything you need to take videos and photos on.
So in essence I'm going to take you from this boring background
to something more exciting like this.
And I'm going to show you how to build this from start to finish.
Thanks to Home Depot for sponsoring this video
and for a limited time you can take advantage of their labor day savings
happening over at homedepot.com.
I'll tell you more on that later in the video but for now let's get to it.
Now that I have all my materials I'm going to cut down a couple pieces of 1x3
to go ahead and create the frame.
A circular saw is the only saw you will need for this project so that makes it pretty doable.
I laid out the frame to get a visual of what I'm going to assemble.
Now although you don't need a pocket hole jig for this project
I just happened to have one and I felt like it made it a bit easier.
I drilled two holes on each end of the studs then I repeated that until I completed them all.
Now it's just a matter of assembling everything together.
I started with the frame and then I worked my way in.
And for the purpose of this project it's not crucial but I spaced all the studs equally apart.
Now that I have the first side complete I jump to the other end to close off the frame.
Before I secure the inner studs I check for squaring on the frame.
At this point I have some wiggle room so I can shift the frame back and forth until I get it squared.
After I square that up I can now finish off the frame.
I have my frame as square as possible so I'm going to leave it flat on the floor
and do not disturb it too much.
Then I took some wood glue and applied it along the side.
The wood glue is going to do a great job of holding on to this quarter inch sheet of plywood.
I went with the plywood because it was smooth on one side and on top of that it was also very light.
I line up the plywood to the frame and then I use a brad nailer to secure the plywood.
This is a full sheet of 4x8 plywood and because of the height I chose
I'll need four sheets of plywood for this project.
When this project is done you'll be able to use it indoors and roll it outside when you need to.
So the weight is super important and also the height of it is important.
As long as the door is below 80 inches I'll be able to roll this into any bedroom.
Unlike the first sheet of plywood I have to cut the second plywood to fit the frame.
Right where the two pieces of plywood meet that's a weak point
so I need to add some sort of backing which is what I'm doing here.
Just like the first side I'll apply wood glue to the side of the frame
then I'll lay the plywood down and nail those on.
Now that the wall is built I need to put it on wheels.
Now these are not my favorite wheels but for this project this
works because it gives me the perfect height to fit through the doorway.
Aside from the casters we'll need some lag bolts, 2x4 and some brackets.
I lined up the casters to the 2x4, marked the holes and then drilled them.
With the holes pre-drilled I can line up the casters and now install the lag bolts.
You can get by without using these metal brackets but you have to properly support this to the feet.
These brackets are pretty strong and I think it gives off the cleanest look.
Attaching the brackets to the wall seems to be the easiest way by leaving it on the floor
and clamping it.
I pre-drilled the holes, installed the lag bolts and then it was on to the other side.
Trying to figure out the order of these things can be a bit tricky but
to speed this process up I'm going to mark exactly where the bracket is going to land
on the feet.
To add the feet I need to lift this and since there's no handle a clamp works great.
One side of this wall is going to be wrapped with pallets and
I'm painting the wall so that you can't see through the pallets and possibly see the plywood.
Majority of the time when I'm painting an interior project
I'm often using a paint with primer mixed in to sort of speed up the process.
I don't spray a lot but I absolutely prefer that method and because I don't have a good
ventilation system I often see a lot of over spray.
Now I have some pallets that's been sitting in the sun for quite some time so
a lot of them do have a bit of an aged look to it which is what I was going for so I'm
very excited about that.
My only concern was do I have enough to complete this project.
When working with pallets you can find some good stuff and
often you can find some stuff that are not so great.
Before using these pallets I need to clean them up and I'm going to use a circular saw
to cut off the ends to create a straight edge so that they can all fit together.
The pallets are cut to different lengths and that should give a random look.
Once I'm done with all the cutting I separated the pallets into different piles.
Each pile was based on the width of the pallet which is
important to keep the consistent look going across.
Each row will have random pieces of pallets.
The only caveat is they need to be the same height.
The quickest way to install these is using a brad nailer and I use one inch nails for
these pallets.
Now each row needs to be the same thickness this way I keep a straight line going all
the way across.
Once the first row is complete I'll start the next.
This process is going to be pretty repetitive installing all of these pallets so I'll
continue doing that and let you in on the latest.
Labor Day is approaching and who doesn't like to save?
We all have things to do and I understand the concern of going out.
There's no better time than right now to take advantage of Home Depot Labor Day Saving
Event.
You can find all sorts of deals to tackle your home projects like this M18 cordless
drill and impact driver combo kit with two batteries.
This event covers a wide range of products including paint, paint accessories, bathroom
vanities, storage solutions and for a limited time you can save up to 40% on kitchen and
laundry room appliances.
This event ends soon so now is the time to take advantage of the Labor Day savings by
shopping exclusively at homedepot.com.
This whole process is pretty simple but it does take time.
It's sort of like putting a puzzle together.
As a way to keep going without too much interruption I work from left to right and as you see I
left the right side open so once I get to the end I can take scrap pieces and fill in
those gaps.
Doing it this way allows me to solely focus on attaching the parts.
This wall has two sides to it.
Side one is done.
Now it's time to address side two.
On this side I'll be painting it but I need to fill in the nail heads and also the plywood
joint.
Since I'm painting this I think you can go about this a number of ways whether you want
to use joint compound.
I'm actually using a wood filler and I think either one of those would work just fine.
As the wood filler is drying I'll tape off the areas that would not be painted.
After a while I'm able to sand down the wall and prepare it for paint.
This is a Behr paint which is their marquee line and it's known for the one coat application.
This color here is called Iron Mountain which I really like it.
It's a pretty thick coat and for what I'm using it for here I only use one coat and
it really looks good.
This paint also has primer built in so you can apply primer if you like but you don't
have to.
Unlike the other side I'm not going to spray it and that's because I receive a ton of
overspray.
I wasn't too thrilled about that and that's because I don't have the right setup in
here but that is going to be a project on my to do list and I will be taking care of
that sooner than later.
The wall is pretty much complete now but I want to add something to it that I feel like
is going to make it stand out even more.
I think adding an LED accent panel is going to allow you to change the look and feel of
your background.
Removing this section here will allow me to wrap the LED strip around the accent panel.
After drilling the pocket holes I can put these parts together to create a simple hook
frame.
Right now I feel these parts are going to get knocked around a lot so I'm going to
glue these together so that the joint can stay together as long as possible.
And now this frame is done so I need to create one more.
Now that these parts are fully assembled I'm going to apply wood glue to the back of these
and I'll take the cut off plywood from the previous panels and attach them to these.
The LED strip will be wrapped around this creating that background glow.
The glow is what this is all about.
You don't want to see a hard light behind you but rather a soft light.
So the plywood is going to overhang at least one inch beyond the wood.
Adding this piece to the top gives a finished look and it also stabilizes the hooks.
Originally I was going to make one panel but after looking at this one I liked the concept
so I made a second one and I made this one a bit slimmer because I used lumber I had
versus going out and picking up what I originally designed for this.
And personally I like the slimmed down version a bit more.
The overall idea for this wall is to open up possibilities.
I see the accent panels as an added benefit and this should give you a ton of inspiration
and ideas on what you can do for your background.
Being that I have a couple of these I'll experiment with different finishes.
One key thing here is keeping all the colors flat.
This way surrounding lights doesn't bounce off the paint.
For this first panel I wanted to experiment a bit using a off-white paint and some green.
Now I have a picture in my head but bringing it to life can always be a challenge.
But I'll try my luck and if I don't like it I'll switch it up.
This is a vermin green and I like the color choice it's pretty bold
but I'm just concerned about the coloring technique.
And if it doesn't work out to my liking I can always switch it up and just paint over it
or just paint the entire panel green.
Now going through the motions I do have some mixed feelings about this but
I'm going to go through regardless and I'll evaluate at the end once it's all together
and it's sitting by the wall.
If I don't like it again I'll just switch it up.
I wanted options and that's why I went with a couple different panels and
even going through this I think I'm going to create more panels just so I can
have that additional flexibility.
For the second panel I used a dark walnut danish oil.
I was a bit concerned about the amount I had left in the can
and I was trying my best to stretch this and complete the project with it.
A new container may not have the same tone
so I was scraping the can to get as much as I could out of it.
Thankfully I was able to make it to the end.
Now all I need to do is wrap it with LED strips and we'll get to see the final product.
Unlike the first panel I'll drill a hole to pass the LED through the frame.
Now I'll pass the LED strip through the bottom of the frame
and leave the end of it on the inside near the bottom.
Now that I have the LED attached to the frame I'll cut off the excess.
You can only cut these strips at a specific location so look for the copper marking.
With this setup I can set up my background pretty much anywhere
even if I want it to be in the shop.
Now I have a world of possibilities when it comes to my background
I don't have to let anybody see what my space looks like.
I can change the space and you'll think I'm in a completely different space.
I can take off some of the panels.
I can add individual panels.
I can flip the wall around and just have a blank gray wall.
Like the opportunities are just endless.
If I wanted to I can attach floating shelves to this
and just make it look like I have an office background.
And trust me I know the struggle of running around a space trying to find somewhere to
either do a video intro or an outro.
It doesn't matter if you're doing video calls,
if you're a YouTuber, if you're a photographer,
whatever you are you can have an amazing background.
So whether you're doing it for work or just a personal preference
this wall is pretty doable.
The best part about this it's done.
If you build one share it with me.
I'd love to see what you do to it.
And that pretty much wraps this one up.
Thank you to my Patreon supporters
and shout out to James for being the top supporter of the month.
If you guys are new here be sure to subscribe to the channel.
Smash that like button if you choose to do so.
And make sure you leave a comment down below.
Let me know what you think about this project.
Until next time I'll see you.
