2011-2015 ford explorer oil change

C.L.S. All-IN-ONE
129 followers
19 Video Views·Dec 10, 2022
This is a 2014 Ford Explorer and we're going to change the oil on this today.
Tools needed today are going to be a set of ramps, an oil catch pan, a 15mm wrench, an
oil filter wrench, and a rag.
Our first step is going to get the vehicle onto the ramps.
You'll want to make sure you're lined up good on the ramps before you go up on them.
A shop light can come in very handy underneath the vehicle.
Also a floor creeper can be very helpful, but not necessary.
Alright so you want to go underneath your vehicle, locate your oil pan, which is right
here, and here's your oil plug.
We'll go ahead and drain the oil first.
Go ahead and loosen it up, then you should be able to take it off by hand after that.
And line up your oil pan underneath there to catch the oil.
It's going to shoot out of there pretty good.
I'm going to go ahead and grab a rag because it might get messy here.
I'm going to go ahead and bring my oil pan up closer because I don't know how far it's
going to shoot out here.
And there we go.
You'll want to make sure you keep the oil bolt here nice and clean.
If any dirt gets on that, that can mix in with the engine oil.
Once the oil is done draining, go ahead and replace the bolt and tighten it.
You should be able to hand tighten it most of the way.
And snug it up pretty good with your wrench.
Next, we want to take the old oil filter off.
And it's located right here.
You want to go ahead and get the wrench on that and get it loosened up.
And it gets a little messy, so I'm going to get my rag ready and make sure you have your
oil pan underneath to catch the oil.
Also, when you remove the oil filter, the old one, you want to make sure that the old
gasket isn't stuck up on the engine.
As you can see up here, it's not up there, so we're good to go.
When installing the new oil filter, you want to make sure to lube this ring right here,
the rubber gasket.
What I normally do is just use the old oil, stick my finger in there, and just lube that
gasket up.
That ensures that it doesn't stick next time you have to remove it.
Alright, now we want to go ahead and put the oil filter on.
And what you want to do is hand tighten it as much as you can.
And once you get it as tight as you can with your hands, you want to use a wrench and go
a quarter turn to get it just a little bit snugger.
And there we go.
Now everything should be done down below here.
We're going to go up top and add some oil.
And if you're not super tall like myself, you'll need a stool to get the oil in there.
Alright, your oil fill's right here.
It calls for 5W-20, approximately 6 quarts.
And you'll want to use a funnel so you don't make a mess.
Make sure you clean your funnel, because if you get any dirt in your engine, that's really
bad.
It calls for 6 quarts, but I'm going to add about 5 1⁄2 quarts, and then pull it off
the ramps, and check the oil, and then add as much as needed.
So we've added about 5 1⁄2 quarts, I'm going to go ahead and put the cap back on, and pull
the vehicle off the ramps.
So you want to make sure all your tools are clear before you pull the car off the ramps.
Now that our vehicle's level, we're going to check the oil.
To check your oil level, the dipstick is located to the right of the fill.
You want to wipe off your dipstick, and slide it back in, and pull it out to check the level.
So right now we're in a crosshatch, which is good, but it could use just a little bit
more.
So I'm going to add the rest of that last quart, and we should be good to go.
Alright, so we want to give that oil time to settle that we just put in there.
And go ahead and clean your dipstick off again, and recheck it.
Make sure everything looks good.
And we are at the top of the crosshatch, and we are good to go.
And I don't know if you can see or not, but on the oil dipstick, there are some crosshatch
marks right in here, and those are those marks I'm talking about.
That's what indicates where your oil level is at.
And you want to remember to put that oil cap back on, or it can make a huge mess.
Thanks for watching my video with CLSAllin1.com.
Also a tip for people with the old oil, you can take that to your local auto parts store,
and they will recycle that for free.
