3 Awesome Life Hacks with DC Motor

The Professor
37 followers
9 Video Views·Dec 9, 2022
Next Level
Hi guys, this is a bike starter motor.
Now the starter motors are designed to operate at 12-24V
although the current rating is very high.
Like the minimum rated starter motor is at 160W
which means that it will draw a minimum amount of current
that is going to be 13.33A at free running state, not at loaded state.
You can imagine the quantity of current flow with the thickness of the wires
like this is a complete bolt and this wire is so very thick.
Now here what I have is a 15V 3A power supply from a laptop charger.
So is it going to be enough to start this motor?
Let's find out.
So these are the two terminals.
You can see guys that there is sparking
but the shaft is not even moving from its position.
No movement.
That is because the current being fed to this motor
is not enough to even start it a little bit.
So high current is required.
Now to run high current motors like these
we need a high current power supply.
This is a 40A center tap transformer.
This black wire is the tapping point
while these two red wires are the side wires.
So this set is going to be the primary
and this is going to be the secondary.
This black wire which is thicker
and this is going to carry the high current
and produce low voltage output
for running high current DC motors such as these.
Now you might also be familiar with these two circuits
that I used in my previous inverter video.
This was the oscillation circuit
and this was the switching circuit.
So I did a few modifications
and I am not going to use this oscillation circuit
and this circuit is going to operate without this.
So let's remove this one.
Now all I am left with are 6 transistors
2 13009 and 1 CDC1351
and same for this set.
Now I am going to connect this transformer to this circuit.
Okay, so let's do that.
This is the collector terminal
common collector of this set.
So it will be connected over here.
The collector terminal of this set
has been connected to this wire.
Now the second collector terminal
from this set will be connected to this wire.
Okay, now that is done too.
All I am left with is the center tap wire
this one
and the common emitter
for this switching circuit.
Now the changes that I did to replace the oscillation circuit
I will show you.
What I did was I just used
these two 1 kilo ohm 5 watt resistors
and they have to be 5 watts
because they are going to heat a lot.
So it will be
each of these will be connected
to the base and collector
of the 1351 transistor set.
So this is your clip
that will be connected to the base
of one of the CDC1351 transistors
and connect
one of the resistor terminal
to the base.
Okay, one is connected.
Now the second part.
Now the collector of the other set
will be connected to this terminal.
Okay.
So one resistor has been successfully connected.
Now to the left of two wires
this resistor will be connected.
Okay.
Which is the first one is
your collector terminal.
The middle one is the collector terminal of CDC1351.
To that terminal this resistor
will be connected and
to the base of this
CDC1351
the other terminal will be connected.
Okay.
So now this circuit is going to be both
switching circuit as well as
the oscillation circuit.
Now to power up this circuit
I will use two printer adapters.
Okay, so this is from a printer.
You can see here it is
32 volts DC supply
at 940 milliamps.
So it is close to 1 ampere
and I have another one at
a little bit lower rating.
Yeah, this one.
This is from an HP printer.
Okay.
32 volts at 625 milliamps.
So together it is going to make
around 1.5 amps
and 32 volts in parallel.
So this is what I am going to use
to feed this circuit.
Okay, so these are the two wires
coming out from the printer adapters.
You can see that it is showing
31.5 volts,
31.6 which is almost
32 volts.
So this black tape
indicates the negative terminal
which will be connected to the
common emitter of this
switching and oscillation circuit.
Now all I am left with
is this center tap point
of this transformer and
the positive terminal
from the printer adapters.
Okay.
So this sound indicates that
the system is performing good
as expected.
Now, even though everything
seems fine,
still this setup is producing
alternating current, AC.
So I have to convert it into DC
by connecting a rectifier.
Okay, so guys, this is
a 32 amperes bridge rectifier.
Yeah, KBPC3510 Wanco.
So I will connect this
to the transformer.
The positive.
The AC, you can see here
the AC sign.
Yeah, that will be connected.
This one is AC, this one is AC.
That will be connected to these two wires.
Okay.
Okay, so the first thing is
connecting the terminal.
The second thing is
connecting this wire.
Now the voltage is very low
so it is not dangerous
except for the current
that can burn you
because the current is going to be
very high of course.
Yeah.
So as you can see guys
that it is running now.
Such a high ampere self-start
motor is running with
the printer chargers because
I have stepped up the current value
from 1 ampere to whatever
it is requiring at present
for starting up.
Yeah, let's check if it is really hot or not.
Yeah, it is really
really hot.
The transformer is very hot.
The bridge rectifier is also
burning up.
That is because it has the
maximum current dissipation capability
of 32 amperes.
It was really loaded at this time.
Let's see the
windings.
Yeah, the secondary is also burning
because it is carrying large amount of current.
And since I am using really thin
secondary which is not designed
to carry such high amperes
it could burn after
continuous usage.
Yeah, it is very hot.
So, let's do this
one more time.
So, connecting this
terminal.
Now, this one.
Yeah.
Hey guys, I have another
large PMDC motor.
You can see here.
Yeah, it is really big.
And it has 1.5
horsepower, 4000 RPM
clockwise permanent
magnet. Okay.
So, I am going to
test if this motor
is going to run with this circuit
that I have just made.
Okay. So, let's
test this one as well.
Okay, so guys I have connected
this DC motor
here to the rectifier of this setup.
So, let's test
if this system is capable of
driving this heavy duty
1.5 HP
PMDC motor. Okay.
So, let's go.
You can see that it is running very
slowly but this circuit is
obviously capable enough to
start up this motor.
Yeah, you can see that
the speed is
not very high but still
this circuit being capable enough
to drive up this motor
is a success in itself. Okay, so guys
I hope you like this video. Thank you so
much for watching it. Please hit like
and don't forget to share and subscribe.
Thank you.
